Instructions
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1763870-2_1826264-6_v1_0918_02_dh_m(3)_en
Preparation for Mounting
Before installation, switch the electricity supply and
corresponding circuit breaker and/or automatic fuse
OFF.
Secure against unauthorized restart, e.g. by installing
a warning sign.
Check the power circuit for any remaining voltage
using an appropriate measuring device.
OFF
• Pay attention to the “Safety instructions” section.
• The light must be protected with a 10/16A fuse at the sub-distribution. An earth leakage circuit
breaker must be installed before this.
• Isolate all poles of the mains cable from the mains supply by removing the electric circuit fuse
or switching off the automatic fuse. Then turn off the earth leakage circuit breaker.
• Prepare the surface for installation. It should be dry, clean, at, stable and free from debris.
• Use the holes on the mounting plate as a template to mark where to place the wall plugs.
Determine the mounting direction before drilling the holes.
Mounting and Connection
a) Drill Holes / Insert Wall Plugs
• Use a 6 mm diameter drill bit to drill the holes.
• Check if the included screws and wall plugs are
suitable for the wall material. If in doubt contact a
specialist.
ø 6 mm
b) Open Terminal Compartment
• Use a plus head screwdriver to remove all four cover retaining screws.
• Keep the screws in a safe place.
c) Connect Power Supply Leads
• Remove the outer insulation on the wires to a
maximum length of about 16 mm.
• Strip the insulation on each of the wires on the mains
cable to a length of about 6 mm.
10 mm
6 mm
• When connecting power supply leads, match colours
as indicated. Brown (L), Blue (N). Length of stripped
wire must not be greater than 8mm.
• Make sure that all screw connections on both sides of
the terminal block are sufciently tight.
• Check that the cables are not squeezed, bent or
damaged in any other way.
N N
N
L L
L
IP65 Ingress protection warning. Check that the rubber gasket around the power
supply lead forms a good seal. This will stop moisture from entering the cable inlet
and damaging components in the terminal compartment.
• Use the retainer to secure the power supply leads.
Rubber gasket
d) Close Terminal Compartment / Replace Lamp Cover
IP65 Ingress protection warning. Make sure
the rubber gasket around the around the
covers are in place and form a good seal.
Do not over tighten screws as this may
damage the case.
Make sure the device is securely fastened
and rmly held in place before letting go
e) Switch Electricity Supply ON
• Turn the corresponding circuit breaker and/or automatic fuse back ON.
• If the lamp does not light up, turn OFF power to the circuit immediately.
• Turn OFF the circuit breaker and/or automatic fuse.
• Check the connection to the power circuit.
Care and Cleaning
• Turn off mains voltage to the light (or disconnect it from the mains) and let it cool down
sufciently.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product. To remove stubborn dirt, moisten the cloth
slightly with water.
• Never direct a garden hose or pressure washer etc. at the product.
• Do not wear metallic or conductive jewelry such as necklaces, bracelets or rings when
carrying out maintenance work on the product (including cleaning).
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines. You thus fulll your statutory obligations and
contribute to the protection of the environment.
Technical Data
a) Item Specic
Item No. 1763870 1763871 1763872 1826264 1826265 1826266
Colour Black Black Black White White White
Power 9 W 7 W 5 W 9 W 5 W 7 W
Lumens 630 lm 490 lm 350 lm 720 lm 400 lm 560 lm
Weight 540 g 531 g 520 g 540 g 520 g 531 g
b) General
Input voltage / current ................... 180 - 265 V/AC, 50/60 Hz
Colour temperature ....................... 4000 K
LED beam coverage ..................... 120°
Dimmable ..................................... No
Ingress protection rating ............... IP 65 (protection from low pressure water jets and dust)
Operating conditions ..................... -20 to +40 °C, 0 – 100 % relative humidity
Storage conditions ........................ -20 to +40 °C, 0 – 100 % relative humidity
Dimensions (W x H x D) ............... 212 x 1118 x 90 mm