Instructions

8
1. Introduction
2. Install the App
Download the App ‘DIY Smart’ from ‘Google Play Store’ or ‘App Store’, and install on
mobile phone.
!
NOTIC E:
NOTICE:
Connect your mobile phone to the same router with the camera to register a user ID.
Special Notice: When open the app, you will receive a tip. Please click ‘OK’ to
allow the notifications, otherwise, you cannot receive any notification.
1 2 6
7
Special Notice: If 2 mobile phones use the same account ID to login at the same time, only 1
mobile phone can receive the push notification alarm ring. So if use 2 mobile phones to
connect the device, user should register 2 different account IDs for the 2 mobile phones.
F o r t h e f i r s t t i m e
i n s t a l l a t i o n , p l e a s e t a p
‘ A l l o w ’ . O t h e r w i s e yo u
c a n ’ t r e c e i v e a n y
notification.
9
10
12 13
11
14 15 16
Special Notice: Device don’t support 5Ghz WiFi router, user should use 2.4Ghz WiFi to
connect.
Quick Guide
LW180315-2
4
3 5
Special Notice: Make sure your router had open DHCP function, or you can’t set up the
device.
2. Input your
email and create
password for
your account.
3. Setup device by 'Smartlink' Setup.
After registered, there are 3 ways to setup, 'Smartlink' setup, 'AP connection' and 'Wired
connection' setup.
3. Click to register
Insert memory card and fix antenna, connect power supply. It takes 30 seconds to start device.
1. Click ‘Register’
button
11.
' 1 2 3 ' , t h e n cl i c k 'S a v e '
button to finish setup. (For
d e v i c e e m p t y pa s s w o r d
p l e a s e c r e a t a n e w
password for the device)
Input default password
10. Input
y o u r
d e v i c e
name
9. You
will hear
a sound
‘DING’
from the
device.
15. Delete Device
In ‘ ’for IOS app slide left the device picture and click 'Delete' button and
click 'Confirmed' button to detele the device. For Android app long press the device
picture and click 'Delete' button and click 'Confirmed' button to detele the device.
All devices
2.Click Delete.
3.Click confirmed
1.For IOS app slide left.
For Android app long press
1, Reduce th e co m p u t e r s / s m a r t p hones
quantity connected in the same network.
2, Chang e to u se a bi g ger ba ndwi d t h
network.
Upload bandwidth≥512KBit/s
<512KBit/s or too many
computers/smartphones in the
same network.
Delay or can't work.
Solutions
1, User can connect device to 5 smartphones
to in case 1-2 smartphones are in poor signal
area, other smartphones can still ring and
view.
2, User better to connect smartphone to WiFi
when there is WiFi available.
Warning: Before you use the device, make
sure device is worked in below
environment, or it can't work properly.
Change to use 2.4GHz WiFi.
Environment Support
3G/4G signal ≥75%
2.4GHz WiFi.
All i Pho n e, i P ad , An dr o id
S m a r t p h o n e s a n d m o s t
Android tablets can receive
push notification.
O n l y u s e i P h o n e , i P a d , A n d r o i d
Smartphones and most Android tablets
to receive push notification.
iPone/iPad will not receive
push notification when 3G/4G
netwo rk is t urned off and
battery is low.
i P h o n e / i P a d c a n a l w a y s
receive push notification when
3G/4G network is turn on.
iPhone/iPad user should always turn on
3G/4G network to be able to receive
push notification all the time
3G/4G signal ≤50%,
long delay or can't view video.
Don't support
5GHz WiFi.
Device can't connect.
Few Android tablets can not
receive push notification.
!
NOTI CE:
NOTICE:
By tapping this icon, you
can delete the ID which
no ne ed a l ar m pu s h.
One device ca n push
alarm to maximun 5 IDs.
Pic.12
Pic.13
Pic.14
11. Smartphone Push Notification Ring
5. Setup device by ‘Wired connetion’ .
Insert TF memory card (if you have connect power supply Plug in a network cable
to the device and the LAN port of router. It takes 30 seconds to start the device.
), ,
Step 1:
Special Notice: Mobile phone and camera must be connected to the same router. Otherwise
you can not find camera.
Step2: Add device .by 'wired connection'.
1. Input email and password
2. Click to login
3. Click ‘+’
5. Choose ‘Wired
connection’.
4. Choose ‘Add new
device’ .
Tamper swi tch
Reset
Thread h ole
CDS Senso r
LENs
Speaker
Ring Butt on
Microph one
IR LED ligh t
Power adapter
Antenna
Step 3: Lead the wires through the hole in the
wall , an d pu t th e d e vice int o th e ba c k
housing. Tighten the screw in the bottom.
Step 5: Connect the wires of power supply, antenna, etc. in other side of the wall. If you
use the existing old doorbell's power, you need to remove existing old indoor unit and
connect the power wires to be able to supplier power to the WiFi doorbell.
Step 2:
Fix the back housing on the wall with two screws
St e p 4 : C o n n e c t t h e an t e n n a , r e m o v e
antannea's sticker and stick antenna on the
wall.
Step 1:
Drill a hole for the wires to go through the wall, use the hexagonal screw driver
in the box to remove the rain cover screw at the bottom of the device. Remove
the rain cover sticker and stick the ring cover on the wall.
Please confirm the correct Wi-Fi setting and insure the position with good Wi-Fi
signal before mounting on the wall. Otherwise, it needs to relocate the router or
the antenna direction to receive the good Wi-Fi signal. If the Wi-Fi signal is still
not strong enough, please add the Wi-Fi repeater or use the network
cable.Make a mounting hole similar size as the back housing of the device. Drill
a hole for the wires to go through the wall.
Remark:
Notice: The wifi antenna should be installed inside the house to have better
signal.
16. Mount on the Wall
14. Reset the device
All devices → → ’, choose ‘Admin password’ to modify device’s password.security settings
13. Modify device’s password
Tap ‘Security Setting’
Input old password and the new
password, then tap ‘Save’. New
p a s s w o r d m u s t b e 6 - 3 0
c h a r a c t e r s i n c l u d i n g b o t h
alphabetic and numbers.
Tap ‘Admin password’
Press and hold the reset button
for 3 seconds until you hear a
‘ D E E ’ s o u n d . A f t e r r e s e t
succeed, wait the device restart
and have ‘Du.Du.Du...’sound.
Model Specification
Image Sensor
Compression
Resolution
Memory
Lens
Sensitivity
IR LED
Night vision distance
IR-CUT
WiFi Antenna
Size
Power Supply
Working temperature
Working humidity
IP level
Indoor door chime specification
Power input
Wireless frequency
Wireless distance
Installation height
Open lock box specification
Working Power
Wireless frequency
Wireless distance
Max. load power
Max. load voltage
1/4" Color CMOS Sensor
H.264
HD：1280*720；S D：640*360；LD：320*180
Optional, Max. 128G.
Fixed 2.5mm 122°
0Lux ( IR ON ) / 0.5Lux ( Normal )
4 × Ф4
Max. 2 meters
Optional
10DB
L55xW40xH129mm
DC/AC 8-24V, optional adapter DC 12V500mA
-20 ~ 50
10% ~ 80% no condensation
Ip65
3×
℃ ℃
1.5V AA battery
433MHz
<50 meters open air
Suggest >1.5meters
DC 12V
433MHz
<50 meters open air
800W
14VDC / 120VAC
A:
Q10. Why I can't open the lock?
Possiblely your connection to the lock is wrong, pls check the lock's required signal.
How can I updated my app if I face problem?
How can I updated my device if I face problem?
Pls get in the app and go to ' ->Settings' and click ‘ ' to update to
newest version.
Go to AppleStore and GooglePlay to check app update version to update to newest version.
Firmware update
A:
Q11.
A:
Q12.
Why my Android tablet can not receive push notification?
Device don't support few Android tablets, pls change to use iPhone, iPad, Android
Smartphones and most other Android tablets to receive push notification.
Why I can't send alarm emails?
Maybe you haven't set 'Enable POP/SMTP for mail' in your email's settings. Pls set 'Enable
POP/SMTP for mail' in your email's settings to be able to send alarm
A:
Q13.
Q14.
A:1,
Why I can't receive push notification ring on my phone?
Q4.
A:
Make sure app's ‘Device->Settings ->Alarm Settings->Receive alarm prompt’is enable.
Make sure the app is running at phone's background, and you haven't force stopped the app
in phone's appliction manager.
Make sure you had chosen ‘OK’to allow app to send you notification when you first install the
app. Or check your phone's notification center to enable receiving app's notification.
If 2 mobile phones use the same account ID to login at the same time, only 1 mobile phone
can receive the push notification alarm ring. So if use 2 mobile phones to connect the
device, user should register 2 different account IDs for the 2 mobile phones.
1,
2,
3,
4,
5,
Maybe you are using iPhone, but you have turn off 3G/4G signal. iPhone's WiFi
connection will intermittently disconnected, if 3G/4G is also turn off user can not receive
push notification. So user should keep iPhone's 3G/4G signal always connected to
received push notification all the time.
Why Video and voice delay when I mount the doorphone on the villa fencing or far outside?
Possiblely because the distance and thickness of blocks exceeds the transmitting ability of
antenna. User can choose to use a 16DB fixed direction antenna to improve the wireless
signal.
A:
Q7.
When people press the call button of the device or trigger the alarm, there will be a
notification received on the mobile phone screen. For Android, press ‘check’ to view. For
iphone, slide and press ‘→’ to view.
Slide to enter app
Alarm picture
will only appear
when memory
card is put.
!
NOTICE:
Notice:
force stop the Android app in phone's application manager, otherwise phone can't
receive any push notification.
User must keep the Android app running at phone's background, user can't
!
NOTICE:
Notice:
to receivd push notification all the time. Otherwise iPhone can not receive push
n o t i f i c a t i o n w h e n W i F i i s i n t e r m i t t e n t l y d i s c o n n e c t e d o r i P h o n e i s
low battery.
If user use iPhone, user should keep iPhone's 3G/4G signal always connected
Special Notice: Device don’t support 5Ghz WiFi router, user should use 2.4Ghz WiFi to connect.
Special Notice: Make sure your router had open DHCP function, or you can’t set up the device.
Special Notice: Do not connect the network cable, otherwise, the device cannot set the
WiFi by ‘Smartlink’.
1. Input email and password
2. Click to login
6.Input WiFi password
and tap ‘Next step’.
3. Click ‘+’
7 . W h e n y o u h e a r
‘ D u . D u . D u . ’ s o u n d
f r o m d ev i c e , c l i c k
8.Turn up the volume of mobile phone and
close to device and click Next Step button.
4. Choose ‘Add
new device’
5. Choose ‘Smartlink’
Smartlink to set Wifi can be done only once. If user need to add device to other mobile
phones, user don’t need to Smartlink again. User should press the button in the ‘All
devices’ choose"Add online device" to enter "Add online device"interface,input device
ID,name and password to add device.
6. Add device to another mobile phones.
Step 4:
Unplug the netwrok cable.
Special Notice: Make sure not to select ‘WiFi’ box in the ‘Network Type’ area,
the WiFi list will automatically show up.
A:
Why can’t hear the voice clearly, picture delay, voice delay, halt or no sound.
Possiblely because network not good and stable. try to change a better bandwidth network.
Possible there are too many other devices like computers on the same router, pls close
these devices or change to a bigger bandwith network.
Maybe the device is too far away from your router, pls put it closer to your router or change a
stronger signal router or add a WiFi repeater in between.
Q6
1,
2,
3,
Maybe the device is too far away from your router, pls put it closer to your router or change a
stronger signal router or add a WiFi repeater in between.
Mayb e your ne t wor k up loa d bandw i dth is to o s m all <5 12KB i t /s o r t oo m any
c o m p u t e r s / s m a r t p h o n e s i n t h e s a m e n e t w o r k . U s e r s h o u l d r e d u c e t h e
computers/smartphones quantity connected in the same network or change to use a bigger
bandwidth network.
2,
3,
Why does the device cannot connect to router through WIFI?
Input wrong WIFI password. Please connect the network cable and input the correct
password.
You may use 5Ghz WIFI. The device doesn't support 5Ghz WIFI. User should use 2.4Ghz
WIFI to connect.
Maybe device is too far away from the router. Pls put device close to router.
Maybe your router’s WiFi have special settings, pls reset your router.
Maybe your router haven't open DHCP. Pls open DHCP in your router.
1,
2,
3,
4,
5,
Q2.
A:
Why my device is offline after I setup to All devices?
There is delay in showing the state, pls slide down on the All devices to refresh to online
state.
Maybe you haven’t setup the device or had changed the device to another place with a new
WiFi, you need to reset the device, press the reset button for 5 seconds until hear
‘DEE’sound and do Smartlink Setup or Cable Setup again.
1,
2,
Q3.
A:
FAQ
1,
2,
3,
4,
5,
6,
Q1.
A:
Why I can’t add device by Smartlink or AP WiFi’ setup?
Maybe you are using 5Ghz WiFi router, device don’t support 5Ghz WIFI, user should
use 2.4GHz WIiFi router to connect.
If device is connected with net cable, it can not do Smartlink or AP WiFi, user should
remove net cable and do Smartlink or AP WiFi setup.
Device should have ‘Du. Du. Du. Du. .... ’ sound to notice user to do Smartlink or AP
WiFi setup if device have no 'Du. Du. Du. ... . ' sound means the device is not normal.
User should press the reset button for 5 seconds until hear ‘ DEE’ and do Smartlink
or AP after hearing the 'Du.Du. Du. ... . 'notice sound.
Device is designed not able to do Smartlink or AP WiFi setup for 2 times. If want to
change Wifi in another place, user should press the reset button for 5 seconds until
hear ‘ DEE’ and do Smartlink or AP after hearing the ' Du. Du.Du.... .' notice sound.
Maybe device is too far away from the router. Pls put device close to router.
Maybe your router haven't open DHCP. Pls open DHCP in your router.
‘
Why some times it takes too long time to connect to video, or fail to connect to video, video
delay, video not fluent or video stop?
It is possibly because your mobile phone is using 3G network and at that place the 3G
network signal is not good enough and percentage is only 25% or 50%. If 3G network
percent is below 75%, it is not good enough to transfer video file, user should change to
other place for better mobile 3G signal or change to use WIFI signal. Moreover, 1 device can
send push notification ring to max. 5 mobile phones at the same time, user should set more
mobile phones to receive the push notification ring to avoid this 3G signal not good at some
places problem.
Q5.
A:
1,
Choose
your WiFi
name
Input WiFi
Passwerd
Step 3: Set wifi. In
in the wifi list.
‘All devices→Device→ →Network setting’ Choose your wifi name
6 . C l i c k
device ID
7. Input your
device name
8.
' 1 2 3 ' , t h e n cl i c k ' S a v e '
button to finish setup. (For
d e v i c e e m p t y pa s s w o r d
p l e a s e c r e a t a n e w
password for the device)
Input default password
email from device.
Maybe your email had switch on '2-Step Verfication'. You should switch off '2-Step
Verification' in your email's settings to be able to send alarm email from device.
2,
1.Choose ‘Alarm
Record’ to record
w h e n a l a r m
triggered or visitor
press ring button.
Device will have 'Du.Du. Du. ... .' sound noticing user to do Smartlink.
Special Notice: If device have no ' Du.Du.Du.... .' sound, User should
press the reset button for 5 seconds until hear ‘ DEE’ and do smartlink
after hearing the ' Du.Du.Du.... .' notice sound.
Insert memory card and fix antenna, connect power supply. It takes 20 seconds to
start device, then device will have ' Du. Du. Du.. . . . ' sound noticing user to setup.
Special Notice: Do not connect the network cable, otherwise, the device
cannot set the WiFi by ‘AP connection’.
If can't setup device by 'Smartlink', you can choose ‘AP connection’ as below.
4. Setup device by ‘AP connection’
Special Notice: Device don’t support 5Ghz WiFi router, user should use 2.4Ghz
WiFi to connect.
Special Notice: Make sure your router had open DHCP function, or you can’t set
up the device.
1. Input email and password
2. Click to login
3. Click ‘+’
4. Choose ‘Add
new device’
5. Choose AP connection
6. Input WiFi password
and device password
and click Next.
7. When you hear ‘Du.
Du . D u … ’ sound from
device, click ‘Hear a beep
for connection’ button.
If can't setup device by 'AP connection', you can choose wired connection as below.
9 . F o r I O S , e n t e r
iPhone’s ‘Settings->WiFi’
and connect to network
‘GW_AP_xxxxxxx’
10. Click the push notice
to return to APP.
11. After here a ‘ng’
sound from device,
click here to finish setup.
Note: Device ID Can be found at the device label or in ‘All devices->Device->Edit’ as below.
7. Date and Time
In"All devices device Time settings- - - ”, choose your
network time automatically and check if the new time is right or not.
Time Zone,press save to get
Remark:
Time zone example: China UTC+8
Germany/France/Spain/Poland/Italy/Netherlands/Norway/Sweden UTC+1
UK/Portugal/Ireland UTC+0 Turkey/Romania/Finland UTC+2
Mexico UTC-6 Colombia/Ecuador/Peru UTC-5
Venezuela/Chile/Manaus UTC-4 Agentina/Uruguay UTC-3
12. Video Record and Playback
Step 1:
Turn off power and insert memory card and turn on power. (DO NOT insert or
remove memory card when device is power on).
Enter"All devices-device- -recorng settings"to click"format SD card"
and click confirmed to format ;
Enter"All devices-device- -recorng settings"choose"record mode"
and"record length"to record
Step 2:
Step 3:
17. Tamper Alarm
When the thief open the device, it will have siren alarm, and your phone will receive alarm too.
(The tamper alarm will be last for 1 min.)
10. Open lock box connection and pairing
Connect open lock box to your electric lock according to different type of locks.
Paring:
Open app and press key button, choose lock number to pair and see confirm to unlock interface,
Delay time setting:
User can long press the open lock box’s pairing button for 7 seconds until LED light stop
flashing to remove paired unit.
Delay setting button
Pairing button
LED indicator light
1, Press key button
4, Click Confirm button
2, Choose lock number
to pair
3, Press open lock box
pair button LED light off
5, LED light
flash 3 time
finish paring
3. Press Delay
setting button and
LED flash to finish
delay time setting.
Why I hear a shrill sound, too small sound or can't hear sound from the doorphone on my
Android phone?
Different phone model have different volume. User can adjust the volume of the phone to
have better sound.
Why the device have noise and echo.
Possiblely because the mobile phone is too closed to the device, move the phone far away
and try.
iPhones, iPad and most Android phone's sound is good engouh. Only few special Android
phone models sound is not good, in this case user can press the 'Talk' Button to hear
only and press again to talk.
A:
Q8.
Q9.
1,
2,
A:
Why the indoor door chime do not ring when I press the outdoor doorbell’s button?
Maybe you haven’t paired well, please pair again.
Maybe the battery is low power, please change battery.
Q15.
A:1,
2,
1.Press Delay setting button and LED off.
2.Press pairing button 1 time for 1 second delay,
press pairing button 2 times for 2 second delay,
press pairing button 3 times for 3 second delay,
……
Maximum 99 seconds delay.
1, For 12V DC lock.
Delay setting button
Pairing button
2, For other locks.
+V = Power supply DC 12V +
GND = Power supply DC 12V -
V+ = Lock Power input DC 12V +
GND = Lock Power input DC 12V -
NO = Lock Power input DC -
COM = Lock Power input DC +
Notice there is a wire between COM and +v
GND
NO
Pic.12
Pic.13
9. Paring indoor door chime
Long press indoor door chimes’ paring button for 3 seconds and hold and long press the
outdoor doorbell’s ring button for 4 seconds. Then release both buttons at the same
time to finished paring.
8. View Interface
Mute
Snapshot
Vertical
Screen
Day and Time
Resolution
HD 1080*720
S D 640*480
LD 320*180
Transfer Speed
Arm/Disarm
Talk
App record
Unlock
Slide on the
screen to
enlarge the
picture
Date
and Time
Transfer Speed
Resolution
HD 1080*720
S D 640*480
LD 320*180
Vertical Screen
Device
setting
Unlock
Device Name
Talk
Snapshot
Mute
App record
User can remove paired additional indoor doorchimes. Fistly take out the battery from indoor
doorchime and wait 10 seconds. Secondly put the battery back in. And within the 2 seconds
while you put batttery back in, long press the indoor doorchime's pair button for 3 seconds and
hold and long press the outdoor doorbell's ring button for 4 seconds. Then release both buttons
at the same time to finish removing all the other paired indoor doorchimes except this one.
2. Click to save
3. Check time
is right or not
1. Set Time Zone
Volume and p airing b utton
Rington e select ion
Special Notice: If device have no ' Du. Du. Du. . . . . ' sound, User should press the reset button
for 5 seconds until hear ‘DEE’and setup after hearing the ' Du. Du. Du. . . . . ' notice sound.
8. For Android click ‘Go
to set WiFi’ button.
1,Long press indoor
door chimes’ paring
button for 3 seconds
and hold
2 , l o n g p r e s s t h e
ou td oo r d o o r b el l’ s
r i n g b u t t o n fo r 4
s e c o n d s . T h e n
release both buttons
at the same time to
finished paring.
Power in (Red) DC /AC 8~24V+
Power in (Black) DC /AC 8~24V-
Doorchime&Lock Antenna Port Female( )
Flat WiFi Antenna port(Male)
Net RJ45(Orange&White)
Net RJ45(Orange)
2
1
3
5
4
6
8
7
Power in (Red) DC /AC 8~24V+
Power in (Black) DC /AC 8~24V-
Doorchime&Lock Antenna Port Female( )
Flat WiFi Antenna port(Male)
Net RJ45(Orange&White)
Net RJ45(Orange)
2
1
3
5
4
6
8
7
IR LED lig ht
Indoor D oorc hime