User manual
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE. 1434331_V1_0616_02_VTP_m_en
Technical Data
Power supply (operation) ..................... by the permanently installed Li-Ion rechargeable
battery
Battery ................................................. rechargeable Li-Ion battery, 3.7 V/DC, 300 mAh
Power supply (recharging) ................... via the micro USB cable; 5 V/DC
Current consumption (charging) .......... max. 1 A
Charging .............................................. via the enclosed micro USB cable; duration approx. 20
to 45 minutes; 300 to 500 charge cycles
Heating time ........................................ to 160 °C in 3 seconds; maximum heating time 30 se-
conds
Sealing ................................................. max. 10000 seals; max. 100 seals per full charge
Supported materials ............................ PP, PVC, PE, OPP & PET bags; non-woven bags,
bags from shrink-wrapped foil (PVC, POF)
Dimensions (L x W x H) ....................... approx. 97 x 30 x 28 mm
Weight ................................................. approx. 73 g
Operating and storage conditions ........ -10 °C to +60 °C; 0% to 90% relative humidity
d) Sealing a bag from thicker lm or aluminium foil
• Hold again rmly one end of the sack and set the handheld lm sealing unit in position (-
gure 4, arrow 1). At that, keep some distance to the device. Press on the cover and wait for
3 seconds until the product preheats.
• Slide the handheld vacuum sealer along the sack to seal it (gure 5); always keep the cover
closed.
The speed of movement depends on the thickness of the sack.
• As soon as you have nished on the right-hand side (gure 5), turn the sack around and place
the sealer onto the part that has not been sealed yet (gure 3, arrow 2).
• Preheat it again for 3 seconds and seal the remaining part of the sack. At that, tack the rst
weld seam.
Before you seal the sack completely, it is advisable to remove the air out of it.
• Now the sack is water- and airtight sealed.
Whenever you stop operation, please remember to preheat the device for 3 seconds
thereafter.
Thicker sacks or bags from aluminium foil are just sealed, but not cut. However, it
depends on the thickness of the bag and sealing speed again.
If you are left-handed, just seal the bag in a reverse direction. See again the 3 small
gures shown bottom left.
• After you have nished using the product, slide the switch from the “Seal” to “Lock” position.
e) Tips and Notes
• If you want to weld bags or sacks consisting of different materials or feature different
thickness‘s, just change the preheat time. Besides, you can repeat preheating in the course
of the sealing operation.
• When preheated for 3 seconds, the heating element reaches the temperature of approx.
160 °C. You can increase the preheat time for max. 30 seconds.
• Due to built-in magnets on the underside of the product, you can attach it to any magnetic
metal surface.
Care and Cleaning
• Disconnect the product from the mains supply before each cleaning procedure (pull out the
micro USB cable).
• Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since
these could damage the housing or even impair operation.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable material and do not belong in the household waste.
Once the product becomes unusable, dispose of it in accordance with the relevant
statutory regulations.