Instructions
• A damaged mains cable may only be replaced by
the manufacturer, a workshop commissioned by the
manufacturer or a similarly qualied person, so as to
prevent any danger.
• CAUTION! Hot Surface. Do NOT touch.
• Warning – do not touch: Hazard of thermal burns by
heat from the soldering iron, solder tip and molten
solder material, and on the soldering iron stand.
• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, strong jolts, high humidity,
moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• The product was constructed according to protection class I. Only a proper mains
socket (230 V/AC, 50 Hz) of the public mains supply must be used as voltage
source.
• The mains outlet must be located near to the device and be easily accessible.
• Never pull the mains plug from the socket by pulling at the cable. Always pull it
from the mains socket using the intended grips.
• Unplug the mains plug from the mains socket if you do not use the device for an
extended period of time.
• Disconnect the mains plug from the mains socket in thunderstorms for reasons
of safety.
• Make sure that the mains cable is not squeezed, bent, damaged by sharp edges
or put under mechanical stress. Avoid excessive thermal stress on the mains
cable from extreme heat or cold. Do not modify the mains cable. Otherwise the
mains cable may be damaged. A damaged mains cable can cause a deadly
electric shock.
• Do not touch the mains cable if it is damaged. First, power down the respective
mains socket (e.g. via the respective circuit breaker) and then carefully pull the
mains plug from the mains socket. Never use the product if the mains cable is
damaged.
• A damaged mains cable may only be replaced by the manufacturer, a workshop
commissioned by the manufacturer or a similarly qualied person, so as to prevent
any danger.
• Never plug in or unplug the mains plug when your hands are wet.
• Warning - risk of re! Do not attach any objects to the soldering station, soldering
iron or cables. Never cover the soldering station or soldering iron.
• Never pour any liquids over electrical devices or put objects lled with liquid
right next to the device. If liquid or an object enters the interior of the device
nevertheless, rst power down the respective socket (e.g. switch off circuit
breaker) and then pull the mains plug from the mains socket. Do not operate the
product anymore afterwards, but take it to a specialist workshop.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. Danger to life
by electric shock! Allow the product to reach room temperature before connecting
it to the power supply and putting it to use. This may take several hours.
• When work is interrupted, completed, or when leaving the working area,
supervision of the soldering station must be ensured until complete cooling.
• For installation in industrial facilities, follow the accident prevention regulations for
electrical systems and equipment of the government safety authority in your country!
• Warning – hazardous vapours: do not breathe vapours generated during soldering
operations. The vapours are harmful to health. Use an exhaust extraction system
if necessary. Always ensure good ventilation of the working area.
• Keep sufcient distance from other heat sources such as hot plates or ovens to
avoid damage to the product.
• Make sure there are no combustible objects or materials near the hot soldering
iron.
• Do not work on live parts.
• Only use the supplied accessories.
• Wear suitable protective clothing, goggles, gloves and sturdy footwear to protect
you from splashing solder material.
Operating instructions
Soldering station Analog 40 W
Item no. 1516976
Intended use
The product is designed for soldering operations in the areas of electronics, hobby and model-
making, where different power levels are required. The control dial is used to set the required
power level. The soldering tip reaches a temperature of approx. 420 °C. This highest power
level may only be used for a maximum of 15 minutes. The product is equipped with two exible
metallic arms and alligator clips. Never use this product to heat up liquids or plastic.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, re, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Soldering station
• Replacement solder tip
• Lead-free soldering tin 10g
• Drying sponge
• 2x exible metallic arm
with alligator clip
• 2x screws (delivered with alligator clip arms)
• 4x spacer
(delivered with alligator clip arms)
• Warning labels
(languages GB, F, NL, IT, PL)
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specic tips and advice on operation.
CAUTION! Hot surface. This symbol on the product indicates surfaces that become
hot during operation. Do not touch.
The product must only be used in dry, enclosed indoor areas. The product must not
become damp or wet, otherwise there is a risk of a fatal electrical shock!
This symbol reminds you to read the operating instructions included with the
product.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• This product is not intended to be used by children
or persons with reduced physical, sensory or mental
abilities or lack of experience and/or lack of knowledge
unless they are supervised by a person responsible
for their safety or have received instructions on how to
use the product.
• WARNING - This tool must be placed on its stand
when not in use. Never leave the heated soldering
iron unattended. Always insert the soldering iron in the
soldering iron stand before switching it on and after
using the soldering station.