Instructions / Assembly

7-6. A Secure Network text box will appear.
• Enter your network password and click OK.
• Make sure your password is correct. If it is entered
wrong, you’ll need to repeat this section.
7-7. The ‘RED’ and ‘GREEN’ lights will stop alternating if the
connection is successl.
• This may take 1–2 minutes.
• If lights do not stop alternating, reset your WiFi Module
by holding the reset button with a paper clip until both
red lights are on. Then repeat all of Step 4.
Proceed to Section 8 (Registering your Wi Module)
(8) Registering your WiFi Module
This will explain how to complete the registration process and
how to access the Glentronics CONNECT website. This website
will be used to edit your stored information and to view the status
of the sump pump system that is connected to the module. The
registration process must be completed only once with the same
email used as email #1. Aer the registration is complete, the
same email can be used to set up other WiFi Modules and they
automatically will be added to the same account.
8-1. You will receive an email from GlentronicsConnect.com at the
email address you provided. Check your junk/spam folder in
case the email is not in your main mailbox.
8-2. Click on the link and complete the registration. (Note: This
link will expire in 24 hours; if link expires before you complete
Section 8, please repeat all steps of Section 7.)
(a) Veri all information entered during setup.
(b) Create a password. The password must be at least 10
characters, include uppercase and lowercase letters, and
at least one number.
(c) Fieen minutes aer registration, the module will
conduct a request for an over-the-air soware update.
If an update is required, the module will automatically
update. This may take a few minutes; during this time the
unit may be unresponsive.
8-3. Launch the app to familiarize yourself with the interface. You
can open the app to check on the status of
your system from anywhere, 24/7.
(9) Testing the setup
9-1. Disconnect the power to the sump pump system connected
to your WiFi Module:
(a) Within a few minutes you will receive a notication.
(b) It will state “AC power is lost”.
9-2. Plug the sump pump system back into AC power:
(a) Within a few minutes you will receive another notication
indicating the system is operating properly.
9-3. You can perform this test with other warnings from your sump
pump system and you will receive a notication with the
corresponding alarm information.
We recommend that you look through Sections 10 and 11 for your
knowledge and understanding.
(10) The Glentronics CONNECT website
This section will explain in detail each page on the Glentronics
CONNECT website. Use this site to stay connected to your
backup sump pump system. It can be accessed by going to www.
glentronicsconnect.com and using your credentials to log in.
10-1. The Devices tab to the WiFi Modules page
This page will allow the user to
edit the information entered
during the setup process. It will
also allow enabling of the
following options:
(a) Receive notications —
enabled as a default. Can
disable if the user does not
want to receive notications.
(b) Allow automatic updates —
disabled as a default. Can
enable if the user wants to
allow automatic rmware
downloads. If enabled, when
new rmware is available, the
WiFi Module will automatically
download it within 24 hours.
10-2. The Prole tab to the
User Prole page
This page will store the user’s
information and can be edited at
any time. This page also is used to
change the password.
10-3. The Status tab to the Status page
This page will display the status of
the pump that is connected to your
WiFi module. The latest registered
WiFi module will display the status
on the screen. If more than one
WiFi module is registered, they
can be selected by clicking on the
dropdown list above the alarm
status. This page will display an
error if the sump pump sytem that
is connected to the sump pump
system has an issue. If more
details are available, an
information icon will appear next
to the error. Click the icon to view
more information.
Alarm Status: This displays the state of the pump system attached
to the WiFi module connected with the USB cable.
4