Instructions / Assembly

2-3. The red and green lights on the WiFi
Module will start alternating.
(a) This means the unit is ready for
setup.
Note: To receive notication during a power outage, you must
have a Wi-Fi router/modem with a built-in battery backup or an
uninterruptible power supply (UPS) powering the equipment.
Proceed to Section 5 (Mounting your WiFi Module)
(3) Accessories
When connected it is possible to add a high water detector using
either a High Water Accessory (BW-WS) or 360˚ Sensor (BW-
WS360). If water reaches the water detector, the WiFi Module will
send a text, email or push notication to the designated devices
stating that high water is present.
3-1. If you will be using this in a sump pit,
sewage pit, or other area that can
handle a ⁄" depth, you need the
following accessory:
(a) High Water Accessory (BW-WS)
This accessory can be ordered by calling
Glentronics at 800-991-0466.
Once you have the part:
(a) Mount the High Water Accessory (BW-WS) with the float
ball below the ‘L’ bracket. If using in a sump or sewage
pit, use the included stainless-steel hose clamp.
(b) Plug the device into
the 3.5mm jack on the
bottom of the WiFi
Module.
Proceed to Section 5 (Mounting your WiFi Module)
3-2. If you will be using this in an area
where you need to be aware when a
minimal water buildup occurs, you
need the following accessory:
(a) 360˚ Sensor (BW-WS360)
This accessory can be ordered by calling
Glentronics at 800-991-0466.
Once you have the part:
(a) Mount the 360˚ Sensor (BW-WS360) with the sensor
pads down and secure in place using the holes in the
sensor panel.
(b) Plug the sensor into the
3.5mm jack on the bottom
of the WiFi Module.
Proceed to Section 5 (Mounting your WiFi Module)
(4) When using as Wi-Fi water alarm only
The Basement Watchdog WiFi Module also can be used as a
standalone Wi-Fi water alarm (additional accessories and charger
required). If water reaches the water detector, the WiFi Module
will send a text, email or push notication to the designated
communication channels, stating that high water is present.
(a) If you will be using this in a sump pit, sewage pit, or
other area that can handle a ⁄" depth, proceed to
Section 4-1.
(b) If you will be using this in an area where you need to
know when a minimal water buildup occurs, proceed to
Section 4-2.
4-1. If you will be using this in a sump
pit, sewage pit, or other area that
can handle a ⁄" depth, you
need the following two accessories:
(a) High Water Accessory (BW-WS)
(b) USB-A Charger (1015016)
These accessories can be ordered by calling Glentronics at
800-991-0466.
Once you have the parts:
(a) Mount the High Water Accessory with the float ball
below the ‘L’ bracket. If using in a sump or sewage pit,
use the included stainless-steel hose clamp.
(b) Plug the charger into a outlet and insert the cord into a
port on the bottom of the WiFi Module.
Proceed to Section 5 (Mounting your WiFi Module)
4-2. If you will be using this in an area where you need to
know when a minimal buildup of water occurs, you need
the following two accessories:
(a) 360˚ Sensor (BW-WS360)
(b) USB-A Charger (1015016)
These accessories can be ordered by
calling Glentronics at 800-991-0466.
Once you have the parts:
(a) Mount the 360˚ Sensor (BW-WS360) with the sensor
pads down and secure in place using the holes in the
sensor panel.
(b) Plug the charger into an outlet and the cord into the
port on the bottom of the module.
Proceed to Section 5 (Mounting your WiFi Module)
(5) Mounting your WiFi Module
You may use either method below to mount your WiFi Module.
5-1. Using the Velcro, mount your WiFi Module:
(a) Peel and stick one side of the Velcro into the recessed
rectangle on the back of the module.
(b) Peel and stick the other piece of Velcro
where you want to mount the module
(a 6' USB-A to USB-C is included, but
you may choose to use a longer cord):
• Top of the battery box
• Top of the backup control box
• To the wall
5-2. Using the included #6 pan head screws, mount the module
to the wall or stud:
(a) Install the screws into the wall or stud (3 inches apart)
(b) Mount the module to the screws using the keyhole
screw mount on the back of the module
BW-WS
BW-WS360
BW-WS
BW-WS360
2