Manual

ManualsBrandsBaseline Systems ManualsRadioEthernet Radio

BL-ER-P Ethernet Radio Unit for Pedestal

Installation Guide

1-866-294-5847 Rev 8.19.2014 www.baselinesystems.com

Assemble the Antenna Riser

1. Remove the antenna riser assembly and the antenna from its packaging.

2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna.

3. Put the stem of the antenna through the

mounting hole on the top of the

antenna riser so the antenna is

positioned on top of the riser.

4. Put the lock washer onto the stem of the

antenna, and then thread the nut onto

the stem. Use a wrench to tighten the

nut sufficiently to ensure that the

antenna makes good contact with the

antenna riser.

5. Remove the Ethernet radio unit from its

packaging.

6. Locate where the antenna cable is

connected on the Ethernet radio unit, and then gently unplug the connector from the

radio.

7. Return the Ethernet radio unit to its packaging so it stays clean and dry.

8. Thread the coax connector on the antenna cable onto the stem of the antenna and

hand-tighten it. Route the antenna

cable towards the bottom of the

antenna riser.

9. Insert the tabs on the backing plate into

the holes at the top edge of the riser and

make sure the plate is snug along the

back of the riser.

Page 1

Summary of content (5 pages)

PAGE 1
BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem of the antenna through the mounting hole on the top of the antenna riser so the antenna is positioned on top of the riser. 4. Put the lock washer onto the stem of the antenna, and then thread the nut onto the stem.
PAGE 2
BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide Prepare the Mounting Location for the Antenna Riser 1. Open and remove the front door on the lower part of the pedestal. 2. On the inside left wall of the pedestal, remove the nuts from the bolts that secure the cover to the outside wall. Set the nuts aside to be replaced in a later step. 3. Remove the bolts that are holding the cover on the outside wall. Set the bolts aside to be replaced in a later step. 4.
PAGE 3
BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide Attach the Antenna Riser to the Pedestal 1. Align the holes at the bottom of the antenna riser with the holes in the gasket at the mounting location on the outside left wall of the pedestal. 2. Feed the free end of the antenna cable through the small hole that you made in the gasket and into the inside of the pedestal. 3. Working from the outside of the pedestal, insert the bolts that you removed earlier into the four holes. 4.
PAGE 4
BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide 3. We recommend that you back up your current configuration before starting this process in case you need to restore your system.  Refer to Backing Up the Controller Programming in the BaseStation 1000 User Manual.  Refer to Backing Up Your System in the BaseStation 3200 User Manual. 4. Halt all watering while you install the Ethernet radio hardware.  BaseStation 1000: Press the OFF button.
PAGE 5
BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide 8. Attach the Ethernet cable to the Ethernet port on the Ethernet radio unit. 9. With the antenna and Ethernet cables pointing up, align the three mounting holes on the Ethernet radio unit with the standoffs on the back wall of the pedestal. Use the screws provided to secure the unit to the enclosure. 10. Plug the 5-pin connector from the Ethernet radio power cord into the upper 5-pin terminal block on the right end of the controller board.