Biometric & Keypad Security Door Lock © 2020 BARSKA® | Pomona, CA 91767, USA (t) 888.666.6769 | (f) 909.445.8169 | www.barska.
Parts Contents Parts 3 Additional Tools for Installation 3 Installation Instructions 4 Operation Instructions 14 Parts of The Door Lock 14 Install Batteries 14 Before You Start to Use 15 Change the Master Code 15 Register a User Code 16 Register a Fingerprint 16 Delete Single User Code and Fingerprint 16 Delete All User Codes and Fingerprints 17 Auto-Lock Function 17 Restore to Factory Default Setting 18 Four Ways to Unlock the Door 18 Three Ways to Lock the Door 18
Installation Instructions 3. Check the position of the front installation hole 2-3/8"（60mm） 1. Check dimensions 2-3/8"（60mm） or . o 1-3/8"-1-3/4" 35mm-44mm 2-3/4"（70mm） or o 2-3/4"（70mm） 1" 1-1/2" 38mm or 2-1/8" o 54mm 25mm Pre-set drive-in latch is 60mm Adjust the latch to 70mm as below if needed 2-3 2. Check if the latch works well A/A2 /8 60 " mm Please make sure the spring bolt is retracted when adjusting the latch 60 70 2 8" 3 2 4" 3 30° 2-3 70 /4" mm 4 w w w.
. Check the size of the side installation hole 5. Check the size of the front installation hole 2-1/8"（54mm） 1-1/2" （38mm） or o Insert the latch to the side hole (Please follow the “up” direction) Fix the bold with 2pcs self-tapping screws up up UP M5*14mm Self-Tapping Screws x 2 2-1/8" 1-1/2" 54mm 38mm Check the latch function with a screwdriver 6 w w w. b a r s k a . c o m w w w. b a r s k a .
6. 7. 1-1/2" 1-1/2"（38mm） 2-1/8"（54mm） or o Pull the connecting wire through the square hole on the back mounting plate, screw the plate to the door back with 2pcs M4 * 24mm screws Install smaller size adaptor ring onto the front door Please retract the latch bolt before you install the front lock body Install the front lock body meanwhile make sure the cylinder tailpiece vertically goes through the central hole of latch.
8. 9. Inset the connecting wire to the cable on the interior lid When the door is left side opening When the door is right side opening 10. Install the thumbturn Please retract the latch bolt before you install the thumbturn as follows. After you install the thumbturn, test it to make sure it moves correctly.
10. Install the battery 11. Test the door lock function after installation 1. Pull the batter case cover upright 2. Fix the interior lid to the mounting plate with 2pcs M4*8mm and 1pc M4*24mm screws 1. Use the key to thumbturn to test the latch in proper installation. 1. Use the key to thumbturn to test the latch in proper installation. 3. Insert 4AA batteries 4. Install the batter case cover 2.
Operation Instructions * Please read all instructions before using this door lock 1. New door lock is in factory default mode: No fingerprint can open the door lock and Default Master Code is 123456. Under factory default mode, you can use default master code to open the lock. 2. For security purposes, change the default master code as soon as possible. 3. Door lock can be opened by fingerprint, user code, master code, or emergency keys. 4.
6. A new master code is set successfully. * Faulty operation will cause five long beeps. Please set it by following above steps again. Register a User Code 1. Touch the screen to activate the keypad. 2. Input the master code, confirm by press “E” and will hear three short beeps. 3. Press “1”, confirm by press “E” and will hear three short beeps. 4. Press User ID (ID: 1-50), confirm by press “E” and will hear three short beeps. 5. Enter a new user’s code (4-8 digits), confirm by press “E “.
* Faulty operation will cause five long beeps. Please enter the codes to set it by above steps again. Restore to Factory Default Setting 1. Take out all batteries; touch the keypad screen for electric discharging. 2. Install all batteries after 10 seconds and will hear two short beep 3. Within 2 seconds, press “C” three times 4. Keypad beeps three times shortly and the lock is restored to factory default setting (all users’ code and fingerprint codes will be deleted at the meantime) 2.
6. Single-use code has been set successfully. * Faulty operation will cause five long beeps. Please restart from the first step of this section. Vacation Mode Under the vacation mode, the door can be unlocked only by master code or an override key. This mode is suitable for office & commercial management during vacation. 1. Turn on vacation mode: - Touch the screen to activate the keypad. - Enter master code and confirmed by “E” and will hear three short beeps. - Press “10”, confirm by press “E”.
1 YEAR LIMITED WARRANTY Biometric & Keypad Security Door Lock BARSKA® Optics, as manufacturer, warrants this new product to be free of original defects in materials and/or workmanship for the length of time specified by this warranty. This warranty does not include damage caused by abuse, improper handling, installation, maintenance, normal wear-and-tear, unauthorized repairs or modifications and tampering in anyway. This warranty is limited to the original purchaser and is not transferable.
