Biometric Key Pad Security Door Lock 10/14 BC407 © 2014 BARSKA® | Pomona, CA 91767, USA (t) 888.666.6769 | (f) 909.445.8169 | www.barska.
Installation Instructions Diagram of lock Lock Body T S Back Front M N A. Front lever handle J. Latch Q. Back lever handle B. Mechanical key K. Back lock body gasket R. Hexagonal screws for fixing the C. Hexagonal screws for fixing the L. Spindle front handle（M4*7） D. Front lock body back handle M. Back plate S. M4*10 screw N. 3 different set of screws are provided T. 3 different set of screws are provided E.
Before installation 1、To ensure a successful installation, please do not use power tools to tighten the screws to avoid damage on the screw. 2、Use the correct fixed-screw tools, and wear eye protection. 3、In order to prevent any unnecessary damage to the door, please drill the holes from both sides of the door separately. ① 1 Door-drilling ② mm/in 26 (1-1/32") 14 (1/4") 55.6 (2-3/16") 58 (2-9/32") φ54 /8") (2-1 60/70 (2-3/8"/ 2-3/4") 100 (3-15/16") 2.
New Door Preparation Note: Drill from both sides of the door to prevent unsightly damage. 1. Place paper template (last page ) onto door and mark for holes. Next drill the hole. 2 Installing the strike plate 1. Mark location of strike on the door frame, making certain that the strike opening is aligned with latch bolt. 4 Type T-door’s installation diagram.
3 4 Installing Latch Installing spindle, and front lock body 2 3/8” [60mm] backset or 2 3/4” [70 mm] backset 60mm 70mm Close view Spindle The latch has two backsets available: 2 3/8” [60mm] backset or 2 3/4” [70 mm] backset Very important note: As the photo shows there is an arrow pointing up to the small triangle. This is the only position where the clutch can be activated during normal operation. Secure the latch to the door using two wood screws supplied.
5 6 Installing the back plate and back lock body gasket 1. The back plate fits into the back lock body gasket 2. Secure the back plate and back lock body gasket with two M5*L screws 7 Battery Installing the back lock body 1. Connect the cable as shown 2. Push the wire connector into the hole under the latch 3. Secure the back lock body with two M4*8 screws and one M4*L 1. Put the batteries in and install the battery cover 2.
8 Testing the operation of the lock How to use mechanical key 1. Rotate the inside handle lever and hold. Ensure that the latch is fully retracted and flush with the latch face plate. Release the inside handle lever, the latch should be fully extended. 2. After batteries putting in the lock, it is going in a normal situation if the latch is retracted inside once rotating the indoor handle and holds it, and also the latch is fully extended once releasing the indoor handle.
Read all instructions before using this door lock WARNING - New door lock is in Factory Default mode, ANY fingerprint can open the door lock. Only successful registered fingerprint and PIN code can terminate Factory Default mode. - For security purposes, register fingerprint and change the factory default code as soon as possible. Default pin code is 12312312312. - Door lock can be opened by either Fingerprint, PIN code and/or Emergency Keys.
Register Guest Press “0,” place admin finger on Fingerprint Scanner, Press “1” then press “3” again and place and hold guest finger on fingerprint scanner until blue indicator light flashes. TEST A NON REGISTERED FINGERPRINT 1. With door open, press “0” and place a Non-Registered finger on Fingerprint Scanner. 2. A few beeps will be heard and red indicator light will flash. 3. Door should NOT unlock.
RESET There are 2 methods to reset fingerprints and pin code to the door lock. Method 1 This method will completely reset the door lock. Remove Battery Cover and remove 2 batteries. Press on any number on the keypad, then locate the 2 reset button, refer to image on the right. Press and hold the 2 reset buttons while re-inserting the 2 batteries. Upon hearing the internal mechanism roll reset is complete and you can release the 2 reset buttons. See image. Note: Any Fingerprint can open the door.
1 YEAR LIMITED WARRANTY Biometric Key Pad Security Door Lock BARSKA warrants this new item to be free of original defects in material and/or workmanship under normal use for a period of twelve (12) months from the date product is received by purchaser. This warranty does not include damage caused by improper installation or maintenance. Damage from misuse, abuse, accident (such as dropping), normal wear and tear, excessive fire, flood, or acts of nature.
This page has been intentionally left blank 12
