AM4800-MAN-BNG-05_1905
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
SR UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
ES ! RU Caution - This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. Atención DA Attention EL Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
EN ! Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product.
PAGE 2 OF 8 Wall plate A Arms B C VESA Plate D Adapter E x1 x1 G H Drilling Template AM x2 Z8 x12 x1 Z9 Z11 x2 TOOLS REQUIRED x1 Z12 Z13 x2 x2 x1 # M Z1 Z2 Z3 Z4 Z10 M4 M6 M6 M8 M8 Z14 L mm 3/4 20 5/8 16 1 25 1 25 1 3/4 45 " Z15 x8 x4 Z5+Z6 4 2 4 4 4 x6 x6 Z18 Z17 x4 x4 7/16" 11mm No.
PAGE 3 OF 8 Connect the VESA Plate to the Back of the TV Caution Solution Purchase longer screws Follow the steps according to your TV's VESA (backscreen hole pattern) 00mm m 250-6 250-400mm 100-200mm 200m A A m -600m 250 1A 200m A 1A 250-400mm 100-200mm 1B Page 4 m A Use spacers [Z14] to adjust screws length inside the TV thread.
1B PAGE 4 OF 8 Connect 4 adapters to the VESA Plate 250x250 .... 600x400 mm D D Z16 Z15 Z17 A 1C TV 1D 250x250 mm...600x400 mm Chose adapter configuration to adjust TV height TV TV Connect VESA plate+adapters to the TV 250x250 ....
Install the Mount on the Wall 2 PAGE 5 OF 8 Check the location of the VESA center compared to the screen center TV center below VESA center 3A TV center fits VESA center Find the studs location. 3B TV center above VESA center Mark VESA center between studs at needed height. VESA Center Stud Findfer A Horizontal bar 3C Place the VESA center of the drilling template on the wall and mark the VESA center. Level the drilling template and mark the holes on the wall. 3D Drill 6 holes.
5 Assemble the Mount for use Connect the Plastic Parts G E Z18 x3 6 A Z18 x3 G Connect the Arms to the Wall Plate Z12 Z11 Z13 B A 7 Weight test - apply force on the upper part of the mount and make sure it is well connected to the studs 132lb / 60kg F PAGE 6 OF 8
PAGE 7 OF 8 Connect the TV and VESA Plate to the Mount 8 9 2 People needed to lift the TV Z9 10 11 Insert and lock the 2 screws to secure the TV. Adjust the friction of the tilt with a screwdriver.
Antenna Cable and Amplifier Connection PAGE 8 OF 8
