Installation Manual

ManualsBrandsBarkan ManualsBarkan TV Mounts40 - 90 inch Full Motion TV Wall Mount with Integrated Amplified HDTV Indoor Antenna 25dB Gain 132 lbs Max Range 50 mile Suitable For Flat And Curved TV Patented Lifetime Warranty

Table Of Contents

AM464L-MAN-ONL-03_2012

Page 1

AM464L-MAN-ONL-03_2012

TV Wall Mount with Integrated

Amplified HDTV Indoor Antenna

Full Motion: Rotate, Fold, Swivel & Tilt

For more information: barkanmounts.com

Suitable only for drywall wood studs

Before installation, please verify that:

• You have a smart TV or decoder

• Your house’s main walls are drywall with wood studs

• It is recommended to use the Antenna mount on an outer wall or on an inner wall

inside a room that has an outer wall

• Your house is within the Digital HDTV OTA signal range (if you are not sure, check

here – https:/tinyurl.com/zu5zagq)

CAUTION This Mount is intended for use only with the maximum weight indicated. Using heavier products might cause injury.

If you are satisfied with the product, please give us a 5 stars  rating on the website you bought it from. If you

are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.

TV Size

13”-90”

33cm-229cm

TV Weight

60kg

132lbs

Summary of content (14 pages)

PAGE 1
Page 1 TV Wall Mount with Integrated Amplified HDTV Indoor Antenna Full Motion: Rotate, Fold, Swivel & Tilt Before installation, please verify that: • You have a smart TV or decoder • Your house’s main walls are drywall with wood studs • It is recommended to use the Antenna mount on an outer wall or on an inner wall inside a room that has an outer wall • Your house is within the Digital HDTV OTA signal range (if you are not sure, check here – https:/tinyurl.com/zu5zagq) For more information: barkanmounts.
PAGE 2
ATTENTION! Please read the following. EN WARNING! Disregarding the safety and assembly instructions may result in the falling of, and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. This mount is not intended for use in public places. For Safety Instructions, warranty and further information, go to: www.barkanmounts.
PAGE 3
UPOZORNĚNÍ! Nedodržení bezpečnostních a montážních pokynů, může způsobit pád a následné poškození Vašeho elektronického přístroje. Po rozbalení, si pozorně přečtěte montážní návod a ve vlastním zájmu jej dodržte. Tento držák není určeno pro použití na veřejných místech. Pro bezpečnostní pokyny a pro více informací se podívejte na: www.barkanmounts.
PAGE 4
EN Caution This mount is intended for use only with the maximum weight as indicated. Using heavier products might cause injury. ES Atención Este soporte debe ser utilizado solo con el máximo peso especificado. Utilizarlo con productos de mayor peso puede causar daños. FR Attention Utilisez ce support en ne depassant pas le poids maximum indiqué. L’utilisation de produits plus lourds pourrait causer des dégats.
PAGE 5
EN Do not install on walls and ceilings made of: gypsum board, drywall, light processed blocks, silicate boards/bricks, a damp wall, weak or very old blocks or wooden panel! For installation on gypsum or light processed blocks please consult with an authorized installer or appropriate building specialist to install the product. ES No instalar en paredes o techos de yeso, silicate, bloques viejos, paredes húmedas, paredes débiles o paneles de madera.
PAGE 6
Included Parts A B Wall Plate Y4 Wall Plate Y3 Plastic Cover Wall Plate Plastic Cover x1 x1 x6 Y2 x6 Y5 Sticker x4 Y1 x6 x6 x1 Z8 x8 W3 Drilling Template x4 Z7 x1 W2 W1 E Adaptor x1 Z4 Amplifier power cable x1 D TV Plate x1 G Amplifier C Front Arms x1 F Page 2 not to scale x2 Y6 x2 Cable Management x1 x2 L L mm inch 6 16 5 Z2 6 25 Z3 4 20 Z5 8 25 1 4 Z6 8 45 13 4 4 # M Z1 8 1 3 4 Required Tools 7/16” 11 mm No.
PAGE 7
Page 3 Connect the TV plate to the back of the TV Wrong Right Purchase longer screws Use the spacers (Z7) in order to adjust the screws length inside the TV Continue according to your TV mounting hole pattern 75 – 200mm 200 – 600mm 1 1b 1a 1a Page 4 75x75 mm up to 200X200 mm hole pattern Z5/Z6 NO FORCE C Z2/Z3 Z4 2 Z7 Optional Page 5
PAGE 8
1b Page 4 Hole pattern above 200x200 mm up to 600x400 mm: Disassemble the screws, connect the 4 Adaptors to the TV Plate and reassemble the screws. PARTIAL TIGHTENING C D D Position the Adaptors according to your TV’s hole pattern Max. 600mm 300mm 600mm 200mm 300mm 300mm Max.
PAGE 9
Page 5 Install the Wall Plate on the Wall 2 Measure the distance between the location of the TV’s mounting holes’ center (marked on the Drilling Template) and the bottom of the TV, in order to set the required height of the TV 5.9” / 14.9 cm E 8” / 20.3 cm 90.4 cm 16” / 40.6 cm ! Make sure the distance between the 2 holes is correct https://www.barkanmounts.
PAGE 10
Page 6 3 Drywall with wood studs installation (16”\ 40.6cm gap between studs) 5 4 6 Make sure all holes are inside the studs Drill with 5/32” \ 4mm drill bit 5/32” \ 4mm X6 CONNECTION POINTS Use a Stud Finder E A 7 W1+W3 FULL TIGHTENING 7/16”/ 11mm 2.75” \ 70mm
PAGE 11
8 Paste the 6 stickers on the Plastic Covers 9 Page 7 Assemble the Wall Plate Plastic Covers Y5 Z8 Z8 Y4 10 Connect the Front Arms (B) to the Wall Plate (A) 11 Weight test Apply force on the upper part of the Wall Plate and make sure it is well connected Y3 Y1 FULL TIGHTENING Y2 B A 12 132Lbs/ 60Kg Place the Wall Plate upright and connect the TV Plate with the TV to the Front Arms Make sure that the TV Plate slots are positioned properly on 2 small beams (Front Arms)
PAGE 12
Page 8 13 Insert and lock 2 screws on each side of the mount, to secure the TV. Adjust the friction of the tilt.
PAGE 13
Page 9
PAGE 14
Page 10