Page 1 Long Dual Arm TV Wall Mount Tilt Swivel Download Assembly Instructions with Text For more information: barkanmounts.com BM464L-MAN-ONL2304 If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.
Included Parts A B Bracket C Front Arms Z7 Z8 x4 x8 W3 W2 Y5 Plastic Cover Wall Plate Plastic Cover x1 x1 x6 Y3 Y2 Cable Management x1 x6 x2 Y6 Drilling Template W1 Sticker x4 x6 E Adaptor x4 S1 Y1 x6 Y4 Wall Plate D TV Plate x1 x1 x1 Z6 Page 2 not to scale x1 x2 P1 P2 x4 x2 x2 P3 x2 L L mm inch 4 20 3ൗ 4 4 Z2 6 16 5ൗ 8 4 Z3 6 25 3ൗ 4 4 Z4 8 25 1 4 Z5 8 45 13ൗ4 4 # M Z1 Required Tools 7/16” 11 mm No.
Page 3 Connect the TV plate to the back of the TV. Wrong Right Purchase longer screws. Use the spacers (Z7) in order to adjust the screws length inside the TV. Continue according to your TV mounting hole pattern. 75 – 200mm 200 – 600mm 1 1b 1a 1a Page 4 75x75 mm up to 200X200 mm (inclusive) hole pattern.
1b 1 Page 4 Hole pattern above 200x200 mm up to 600x400 mm: Disassemble the screws. D 2 connect the 4 adaptors to the TV plate and reassemble the screws.
Position the Adaptors according to your TV’s hole pattern. Max. 600mm Page 5 300mm 600mm 200mm 300mm 300mm Max. 400mm 400mm For more positioning options turn to page 12. Connect the TV Plate with the Adaptors to the TV in all 4 connection holes. Z4/Z5 FULL TIGHTENING NO FORCE Z1/Z2/Z3 Z6 Z7 Optional Optional – Corner installation Functionality may vary depending on the distance from the corner. Max. TV Size 80”\203cm A A 3 Page 7
Page 6 Install the bracket on the Wall Measure the distance between the location of the TV’s mounting holes’ center and the bottom of the TV, in order to set the required height of the TV. E 5.9” / 14.9 cm 2 8” / 20.3 cm 90.4 cm 16” / 40.6 cm Make sure the distance between the 2 holes is correct. https://www.barkanmounts.
Follow the steps according to your wall type. Page 7 3 Make sure all holes are drilled inside the studs. 16" Mark the holes on the wall according to the required height.
4a Page 8 4b First use 1/4” \ 6mm drill bit. Drill with 5/32” \ 4mm drill bit. 1/4” \ 6mm 1 5/32” \ 4mm 2.75” \ 70mm Afterwards use 3/8” \ 10mm drill bit. 3/8” \ 10mm 2 2.75” \ 70mm 2.75” \ 70mm W2 W2 W2 3/8”/ 10 mm 16" A The anchor must be sunk at least 3/8"/10 mm into the plaster coating.
5 Paste the 6 stickers on the Plastic Covers. Page 9 Assemble the Wall Plate Plastic Covers. 6 S1 Y5 S1 Y4 7 Connect the Front Arms (B) to the Bracket (A). Y3 Y1 FULL TIGHTENING Y2 B A 8 Weight test. 9 Apply force on the upper part of the Bracket and make sure it is well connected. Place two nuts (Z8) in the nut-housing (P2).
Page 10 Assemble the nut-housing (P2) make sure that the tab is inserted into the slot. P2 Make sure that the tab is inserted into the slot 11 Assemble part (P3) on the nut-housings (P2). push P3 down until the small part that looks like an upside down “T” passes the highlighted tooth. P3 upside down T part 12 Place the bracket upright and connect the TV plate with the TV. Make sure that the TV Plate slots are positioned properly on 2 small beams (Front Arms).
Page 11 13 Insert and tighten the screws from both sides to create friction for the tilt mechanism. Adjust the TV tilt angle carefully. Z6 Z2/Z3 14 Place the TV cables in the Cable Management. Y6 15 FALL PROOF CABLE MANAGEMENT Level the TV.
Page 12
