Instructions

ManualsBrandsBARCO ManualsWall PlatformBARCO UNI-0005 55 Inch Bezel-less Tiled LCD Video Wall Platform

If you have any difﬁculties installing or servicing your

SmartTrim, call your dealer or Draper, Inc.

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

INSTRUCTIONS

INSTALL ATION & OPERATION

SmartTrim

for UniSee

500/700

(UNI-0005 / UNI-0007)

Overview

TRIM

FLANGE

MOUNTED TO WALL:

Approx. 0.25" (6.35mm)

gap between ﬂange

and wall typical

TRIM FACE

VENTED

FLANGE

Summary of content (8 pages)

PAGE 1
SmartTrim® for INSTRUCTIONS UniSee® 500/700 (UNI-0005 / UNI-0007) INSTALLATION & OPERATION Overview TRIM FACE TRIM FLANGE MOUNTED TO WALL: Approx. 0.25" (6.35mm) gap between flange and wall typical VENTED FLANGE If you have any difficulties installing or servicing your SmartTrim, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.
PAGE 2
SmartTrim® for UniSee® 500/700 (UNI-0005 / UNI-0007) Important Safety Information WARNING Improper installation and use of SmartTrim can result in serious injury or death. Primarily, injuries can occur when the SmartTrim falls due to imprecise installation, mishandling of the SmartTrim during installation or installation on an insufficient wall or ceiling structure. Please use extreme care. 1. Please read the following installation guidelines thoroughly and follow them carefully.
PAGE 3
SmartTrim® for page 3 of 7 UniSee® 500/700 (UNI-0005 / UNI-0007) Section 2 - SmartTrim Components List Standard Parts for all installations For installations larger than 2 x 2 Top Left Trim - (1x) Top Right Trim - (1x) Top Horizontal Trim - (varies) CC287.291SA CC287.293SA CC287.292SA Corner Vertical Trim A - (2x) Corner Trim Brackets - (4x) Corner Trim Brackets - (4x) C002.1553SA C002.1552SA Middle Vertical Trim - (varies) CC287.295SA CC287.296SA Edge Trim Brackets - (varies) C002.
PAGE 4
SmartTrim® for page 4 of 7 UniSee® 500/700 (UNI-0005 / UNI-0007) Section 4 - Attaching SmartTrim Brackets to Barco UniSee Caution: UniSee LCD Display wall must be properly assembled, aligned on all axes and level. 1 Corner Mounting Bracket C002.1553SA CO R A B EE L IS UN PANE LCD (Shown Installed) Corner Mounting Bracket C002.1552SA Washer Use Barco UniSee Service Tool or 5mm Hex 2 OR Barco UniSee Service Tool No.
PAGE 5
SmartTrim® for page 5 of 7 UniSee® 500/700 (UNI-0005 / UNI-0007) Section 5 - Attaching SmartTrim section to SmartTrim Brackets 1. Insert the two (2) guide pins on the SmartTrim section into the receivers on the adjustable mounting brackets. SmartTrim will snap into place against the side of the LCD panels. Please Note: If there are any gaps between the SmartTrim and the LCD panels, or SmartTrim section will not fit, refer to Section 6 - Adjusting SmartTrim Brackets on page 6.
PAGE 6
SmartTrim® for page 6 of 7 UniSee® 500/700 (UNI-0005 / UNI-0007) Section 6 - Adjusting SmartTrim Brackets Please Note: Figures 5-A thru 5-C below show an edge bracket on the side of the Unisee. The same procedure shown below should be used on the top and corners. SmartTrim Adjustable Bracket is always aligned with the vertical center of the UniSee Wall Cross. During installation of the Unisee Video Wall, the position of the LCD seam may have moved in relation to the Wall Cross.
PAGE 7
SmartTrim® for UniSee® 500/700 page 7 of 7 (UNI-0005 / UNI-0007) Section 7 - Removing SmartTrim Panels 1 2 S PRES Figure 6 PRESS If you have any difficulties installing or servicing your SmartTrim, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.
PAGE 8