BARCO PROJECTION SYSTEMS R9840170 R9840171 R9840176 Rugged Remote Control for ELM/SLM Projectors 1
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, October 2001. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.
Contents Contents Safety Instructions ................................................................................................ 4 Notice on Safety ...................................................................................................................................... 4 Installation Instructions ............................................................................................................................ 4 Owner's Record ....................................................
Safety Instructions Safety Instructions Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment.
Safety Instructions FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instructions 3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself. 4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. 5.
Safety Instructions Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: 1. When the power cord or plug is damaged or frayed. 2. If liquid has been spilled into the equipment. 3. If the product has been exposed to rain or water. 4. If the product does not operate normally when the operating instructions are followed.
General Information General Information Rugged Remote Control This Manual regroups several types of Rugged Remote Control Kits, depending on the type of rugged remote considered some information in this manual may become superfluous.
Contents Contents Contents of the Rugged Remote Control Case The Rugged Remote Control Case* contains following items: 1. 2. 3. 4. 5. 6. 7. 8. Boxkit Magik: R593564 Boxkit fit rugged ctr puf: R821134 Rugged Remote Control : R763666 Battery charger: B557208 + EU Plug supplementary plugs US: B5572102 UK: B5572101 AUS: B5572104 SUBD9 Male/Male adaptor R821585 Lamp comms cable: Z34980143 Shoulder Strap : B400559 Installation Manual : R5976251 1 2 4. 3. 5. 6. 7. 8.
Description & Specifications Description Application The Barco Rugged Remote Control enables the control of the Barco ELM and SLM series DLP Projectors and the Barco 6000 series LCD Projectors. The Rugged Remote Control allows following functions: Remote Mode:The Remote Control sends actions to and reads information from the projector Lamp Read Mode:The Remote Control reads information stored in the lamp information Module. Software compatibility G5 SLM: Sofware version V1.
Description & Specififcations Charger Input range : 100-240V (autoranging) 47-63Hz 400 mA Output: 15V DC/1A Input/Output Signals A image 3 B CTRL 3 Two Way Hardwired Remote (CTRL 3) CTRL 4 Lamp Info Module (CTRL 4) P US H SLQ DVVLJQHPHQW *1' '$7$ '$7$ Fixed rate: 57600 baud Cable type: XLR connection, twisted pair Cable type: supplied Serial interface RS 232/422 Serial interface A (image 3) Selectable modes : - RS 422 T: RS422 terminated.
Description & Specififcations Keypad F1,F2,F3,F4,F5 B A E F C D Key Name F1,F2,F3,F4,F5 Function Keys A Browse Keys Function (when not specified : idem RCU) Function keys (determined by the projector) + up/down - - + left/right B Command Keys idem RCU C Validation keys EXIT ENTER D Numeric keys E F LED LED TEXT ON indicaton (Red) PAUSE indication (Yellow) 12
Description & Specififcations Wireless Base Weight: 0.3 kg (0.6 lbs) Communication port A Serial interface C Selectable modes with switch B : - RS 422 T: RS422 terminated.
Installation Setup Installation setup Power Connections The charger The charger can be fitted with the 4 supplied power plugs: 1. 2. 3. 1. Australia 2. US/Japan 3. Europe 4. UK 4. Changing the plug 1. Pull the plug to be changed upwards untill it is completely removed from the charger (Image 1) 2. Place the plug to be mounted on the charger and guide it downwards by using the guiding slots (Image 1 & 2) 3. Push the plug downwards untill it clicks and is locked into the charger (Image 3) 4.
Installation Setup Power ON switch The ON/OFF switch A is located on the right side of the Rugged Remote Control near the DC power plug (image 3). Remark: The Remote Control can also be supplied with the charger permanently connected. A image 3 Supplying the Wireless Base The wireless base is supplied via the projector. The connection needs a standard serial cable linking the 'COMM PORT' of the projector to the 'COMM PORT' of the Wireless Base. The supplied voltage depends on the type of projector.
Installation Setup Charging the batteries The batteries are trickle charged whenever the XLR connection with a powered projector is made or when the charger is connected. Charging is required whenever the batteries are low, the status (ACT/LOW) of the batteries can be seen on the main menu (menu 1) or in the diagnosis menu (see " Installation Settings "). remark: The delivered batteries are not charged.
Installation Setup Changing the batteries The expected life of the batteries is about approximatively 1000 charge and discharge cycles. When replacing the batteries, all batteries should be replaced at the same time. CAUTION Risk of explosion if the batteries are replaced by an incorrect type Dispose of used batteries according to the instructions To change the batteries follow next procedure: 1. 2. 3. 4. 5.
Configuration Setup Configuration Setup Remote Mode Performing Remote Control of the projector The connection of the Rugged Remote Control to a projector uses a standard twisted pair cable with XLR connectors at each extremity (not supplied). The baudrate is fixed at 57600 baud. Image 1 gives an example of a Remote Control connected to a G5 SLM Projector. Image 1 How to Connect 1. Plug the cable in the Remote connector labeled CTRL3 "Two way hardwired remote". 2.
Configuration Setup Lamp Read Mode Reading the Lamp The Lamp Read Mode requires a connection between the lamp unit and the Remote Control using the supplied lamp cable (Z34980143). Reading the lamp is only possible for BARCO ELM and SLM projectors. How to Connect 1. Plug the cable in the remote control connector labeled CTRL4 "Lamp Info Module". 2. Plug the other extremity in the Lamp Unit connector. WARNING To avoid burns always let cool down the lamp before handling it .
Configuration Setup RS232/422 Communication image1 RS 232 - 9600 - 19200 - 38400 - 57600 - 115200 RS 422 T Different baudrate(baud)settings: RS 422 NT The Remote Control allows RS232/422 serial mode communication with the projector. This is used for software upgrade of the Rugged Remote Control or to perform a remote control of the projector (instead of using the CTRL3 Two way hardwired remote). B See 'Menu Setup' for setting procedure. To select the different serial modes use switch B (image 1).
Configuration Setup Software download The RS232/422 port is always enabled, this makes software upgrading always possible.
Configuration Setup RF Mode In the RF Mode the Wireless Remote Control makes it possible to perform an RF communication with the projector through the Wireless base. This is only possible with the Wireless Rugged Remote Control ('General lnformation' page 8) . How to connect The connection between the Wireless base and the projector uses a standard serial cable.
Configuration Setup To perform an RF communication following parameters have to be set (see page 29): RF address This is a selection of an RF channel for the wireless link. Any number between 0 and 63 may be chosen. In the case of multiple wireless links (Image 1 on previous page) each wireless base must have its own RF address. Do not uses different receivers with the same address. Frequency band Sets the frequency band according to the regulations of the country you are working in.
Menu Setup Menu Setup Remark concerning display images The bold items do not appear bold on the screen. This is only done to grasp the attention of the reader. Display layout The two upper lines are a copy of the local LCD of the projector when in Remote Mode or the contents of the Lamp information module when in Lamp Read Mode. In case of a 6000 series LCD projector these two lines are not displayed.
Menu Setup Internal Menu The Internal Menu offers some shortcuts to preprogrammed parameters. RRC INTERNAL MENU $ CONTRAST ) BRIGHTNESS COLOR ) ) + TINT ) PHASE ) SHARPNESS FREEZE HELP - MUTE VOLUME BALANCE BASS TREBLE INSTAL.SETTINGS $ Flowchart 2 In the internal Menu the function keys are preprogrammed with the 5 first items (Flowchart 2). Installation Settings flowchart 3 gives an overview of the parameters within the 'Installation Settings' menu.
Menu Setup Identification menu IDENTIFICATION MENU RUGGED REMOTE CONTROL SOFT VERSION: --.-OPER.MODE:-------+ - browse with: COMM.PORT: ------BAUDRATE:--------ADDRESS:---------BATTERY CHARGING:-- Th identification Menu gives an overview of some parameters within the 'Installation Settings' Menu. The parameters in the 'Identifcation' Menu are Read Only.
Menu Setup Communication Menu Flowchart 1 gives an overview of the structure of the Communication Menu COMMUNICATION MENU AUTO XLR COMM.PORT: AUTO RS232 RF 9600 19200 + BAUDRATE:----- 38400 - 57600 115200 RF ADDRESS[0..
Menu Setup Selecting the communication port To enable one of the communication ports handle as follows: + 1. Browse with when in the 'Communication Menu'. 2. Select 'comm.port' and confirm with . 3. Select with (Menu 1). 4. Exit the menu with or . - NO COMMUNICATION COMMUNICATION COM.PORT: [AUTO] Menu 1 When selecting 'AUTO' following priority is set : Auto enables the XLR port if it is powered.
Menu Setup RF Options The RF Options are only available in presence of the Wireless Remote Control version. RF Options: Changing the RF address + 1. Browse with when in the 'RF Options Menu' 2. Select 'RF Address' (Menu 1) 3. Press < ENTER> 4. Use the numeric or the browse keys to change the value of the address 5. Press < ENTER> to confirm 6. The remote displays following message during a few seconds (Menu 2 ) 7. Exit the menu with or . - NO COMMUNICATION RF OPTIONS RF ADDRESS [0..
Menu Setup RF Options: Synchronize base The wireless base and the remote have to be synchronized (same RF address and freq. band ) To synchronize the base follow next procedure: 1. Connect the 'COMM PORT' of the base to the 'COMM PORT' of the projector using a standard cable (image 1) 2. Browse with when in the 'RF Options Menu' 3. Select 'Synchronize base' (Menu 1) 4. Press < ENTER>, the remote displays following message (menu 2) 5.
Menu Setup Change Address How to change the address: 1. Select 'Change address' in 'Installation settings' (menu 1). 2. Press + 3. Use numeric keys or to fill in the new address ( number between 1 and 255 ) 4. Confirm with - NO COMMUNICATION CHANGE ADDRESS ADDRESS 1 menu 1 Shortcut : Use the key for direct access to the address menu. ( displays also the projector's address) Diagnosis Flowchart 1 gives an overview of the read only parameters within the 'Diagnosis menu'.
Menu Setup Lamp Mode Menu Access to the Lamp Read Mode Menu 1. Press to enter the Internal Menu (menu 1). + 2. Select INSTALLATION SETTINGS by browsing with 3. Select OPERATION MODE by pressing (menu 2). 4. Select the Lamp Read Mode by pressing , menu 4 is displayed. 5. Exit the Internal Menu by pressing or .
Menu Setup Remote Mode Menu Access to the Remote Mode 1. Press to enter the Internal Menu (menu 1). + 2. Select INSTALLATION SETTINGS by browsing with 3. Select OPERATION MODE by pressing . 4. Select the Remote Mode by pressing , menu 5. Exit the Internal Menu with or . - is displayed. NO COMMUNICATION NO COMMUNICATION INSTALLATION SETTINGS CONT BRIG COLO TINT PHAS INSTALLATION SETTINGS OPERATION MODE menu 2 menu 1 NO COMMUNICATION OPERATION MODE OPER.
Additionnal Information Additionnal Information Messages MESSAGES POSSIBLE CAUSES NO COMMUNICATION -hardware -parameter mismatch NO DISPLAY DATA AVAILABLE -No display on projector (6*00 series projectors) RF=LOW -parameter mismatch -no supply NO UPDATE during synchronisation update (polling) is interrupted 34 TO CHECK -connections -address match proj/RRC -baudrate match proj/RRC - -RF addr match proj/RRC -Freq band match proj/RRC perform synchronization if necessary (page 30 ) -connection (com
Mechanical Information Mechanical Information Dimensions The external dimensions (mm) of the Rugged Remote Control are illustrated in drawing below: 63 60 189 165 165 45 5 35
Mechanical Information Mechanical Information The external dimensions (mm) of the Wireless base are illustrated in drawing below: 129 36
BARCO NV / Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium 37
