BARCO PROJECTION SYSTEMS BARCO PROJECTION SYSTEMS RCVDS 05 RCVDS 05 R9827880 R9827881 R9827888 R9827889 OWNER'S MANUAL Date: 30.06.98 R5975765 RCVDS05 020997 Revision : 06 R9827880 R9827881 R9827888 R9827889 OWNER'S MANUAL Art. No. R5975765 1 Date: 30.06.98 R5975765 RCVDS05 020997 Revision : 06 Art. No.
Due to constant research, the information in this manual is subject to change without notice. Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, June 1998. All rights reserved. Produced by BARCO NV, June 1998. All rights reserved. Trademarks are the rights of their respective owners. Trademarks are the rights of their respective owners.
I. Safety instructions ............................................................................................. 7 I.1 Notice on Safety .................................................................................... 7 I.2. Installation instructions ......................................................................... 7 I.3. On safety .............................................................................................. 9 I.4. On installation .............................................
TABLE OF CONTENTS 4 C.2.2. Signal connection between multiple RCVDS05's. ........................ 34 C.3. Optional Remote IR receiver to RCVDS05. ..................................... 35 C.2.2. Signal connection between multiple RCVDS05's. ........................ 34 C.3. Optional Remote IR receiver to RCVDS05. ..................................... 35 D. RCVDS05 used as high bandwidth signal splitter. .............................. 37 D.1. Use of multiple output modules. ................................
TABLE OF CONTENTS TABLE OF CONTENTS VII. Error codes ................................................................................................... 66 VIII. Optional decoder ......................................................................................... 68 VIII. Optional decoder ......................................................................................... 68 TABLE OF CONTENTS TABLE OF CONTENTS VII. Error codes .................................................................
TABLE OF CONTENTS 6 TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS R5975765 RCVDS05 020997 6 R5975765 RCVDS05 020997
SAFETY INSTRUCTIONS I. SAFETY INSTRUCTIONS I. SAFETY INSTRUCTIONS I.1 Notice on Safety I.1 Notice on Safety RCVDS05s are built in accordance with the requirements of the international safety standards IEC 950 and UL 1950, which are the safety standards of information technology equipment including electrical business equipment.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons. The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk of electrical shock to persons.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS * All the safety and operating instructions should be read before using this unit. * All the safety and operating instructions should be read before using this unit. * The safety and operating instructions manual should be retained for future reference. * The safety and operating instructions manual should be retained for future reference. * All warnings on the projector and in the documentation manuals should be adhered to.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS B. Power cord with ANSI 73.11 plug: B. Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code. The wires of the power cord are colored in accordance with the following code. Green/yellow: ground White: neutral Black: line (live) * Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. * Do not allow anything to rest on the power cord.
SAFETY INSTRUCTIONS This product should never be placed near or over a radiator or heat register. This switcher should not be placed in a built-in installation or enclosure unless proper ventilation is provided. I.5. On servicing I.5. On servicing Do not attempt to service this RCVDS05 yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock! Refer all servicing to qualified service personnel.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. I.7. On repacking I.7. On repacking Save the original shipping carton and packing material; they will come in handy if you ever have to ship your set.
INTRODUCTION INTRODUCTION II. INTRODUCTION II. INTRODUCTION The RCVDS05 offers the possibility to connect a wide range of video, data and graphics sources to one or more projectors or other displays. Its modular input design makes it possible to easily adapt the switcher to the user's input requirements. This RCVDS05 can be equipped with up to 10 input modules. The RCVDS05 offers the possibility to connect a wide range of video, data and graphics sources to one or more projectors or other displays.
INTRODUCTION INTRODUCTION 2. As splitter. 2. As splitter. Communication link Composite Video Composite Video RGB Analog RGB Analog Communication link Composite Video Composite Video RGB Analog RGB Analog RCVDS05 RCVDS05 Comp. Video RGB Analog Comp. Video RGB Analog RGB Analog RGB Analog Comp. Video RGB Analog Comp. Video RGB Analog 3. As stand alone system switcher. 3. As stand alone system switcher.
INPUT MODULES III. INPUT MODULES III.
INPUT MODULES INPUT MODULES A. Input module installation. Up to 10 input modules can be inserted in any order in the RCVDS05. Up to 10 input modules can be inserted in any order in the RCVDS05. Install the input modules in the RCVDS05 as follows : Install the input modules in the RCVDS05 as follows : 1. Power down the RCVDS05 and disconnect the power cord from the wall outlet. 1. Power down the RCVDS05 and disconnect the power cord from the wall outlet. 2.
INPUT MODULES INPUT MODULES B. Source connection to the RCVDS05. B. Source connection to the RCVDS05. B.1. Input module : Video/S-Video. B.1. Input module : Video/S-Video. Order number : 98 27900 Order number : 98 27900 Signal connection : video composite, S-video and audio. Signal connection : video composite, S-video and audio. Composite Video : 1xBNC 1.
INPUT MODULES INPUT MODULES Straps on module level : Straps on module level : Floating or non-floating input. Floating or non-floating input.
INPUT MODULES INPUT MODULES B.2. Input module : RGBS/RGsB analog. B.2. Input module : RGBS/RGsB analog. Order number : 98 27910 Order number : 98 27910 RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if sync on green Vert. sync : 1 Vpp to 4 Vpp ± 3 dB Hor. sync / Composite sync : 1 Vpp to 4 Vpp ± 3 dB RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if sync on green Vert.
INPUT MODULES INPUT MODULES - 6 - - - - < 1 & 6 ( / ( & 7 ,2 1 6 H S D U D W H V \ Q F - - - 6 < 1 & 6 ( / ( & 7 ,2 1 - - - 6 \ Q F R Q J U H H Q - Non-Floating Non-Floating ) OR D W LQ J R U Q R Q I OR D W LQ J LQ S X W ) OR D W LQ J R U Q R Q I OR D W LQ J LQ S X W Floating INPUT MODULES INPUT MODULES Floating 20 6 H S D U D W H V \ Q F 6 \ Q F R Q J U H H Q R5975765 RCVDS05 020997 20 R5975765 RCVDS05 020997
INPUT MODULES INPUT MODULES B.3. Input module : RGB3S/RG3sB analog. B.3. Input module : RGB3S/RG3sB analog. Order number : 98 27920 Order number : 98 27920 RGB3S/RG3sB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if Tri-level sync on green Vert. Tri-level sync : 1 Vpp to 4 Vpp ± 3 dB Hor. Tri-level sync / Composite Tri-level sync: 1 Vpp to 4 Vpp ± 3 dB RGB3S/RG3sB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.
INPUT MODULES INPUT MODULES B.4. Input module : Component Video input B.4. Input module : Component Video input Order number : 98 27930 Order number : 98 27930 Component video : 4 x BNC R-Y : 0.7 Vpp ± 3 dB B-Y : 0.7 Vpp ± 3 dB Y: 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if Tri-level sync on green Composite sync : 1 Vpp to 4 Vpp ± 3 dB Component video : 4 x BNC R-Y : 0.7 Vpp ± 3 dB B-Y : 0.7 Vpp ± 3 dB Y: 0.
INPUT MODULES INPUT MODULES )ORDWLQJ RU QRQ IORDWLQJ LQSXW )ORDWLQJ RU QRQ IORDWLQJ LQSXW Non-Floating Non-Floating Floating - - - - - - - - - - 6\QF VHOHFWLRQ 6 H S D UD WH V \ Q F 1 R UP D O 6 \ Q F R5975765 RCVDS05 020997 - 6 \ Q F R Q < 7UL OHYHO 6\QF INPUT MODULES - 23 - - - - 6\QF VHOHFWLRQ 6 H S D UD WH V \ Q F 1 R UP D O 6 \ Q F R5975765 RCVDS05 020997 6 \ Q F R Q < 7UL OHYHO 6\QF INPUT MODULES Floating 23
INPUT MODULES INPUT MODULES B.5. Input module : RGBS/RGsB analog for Line Doubling* B.5. Input module : RGBS/RGsB analog for Line Doubling* Order number : R9828410 Order number : R9828410 RGBS/RGsB analog : 4 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if sync on green Comp. Sync : 0.3 Vpp to 4 Vpp ± 3 dB RGBS/RGsB analog : 4 x BNC Red : 0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if sync on green Comp. Sync : 0.
SPECIAL MODULES SPECIAL MODULES IV. SPECIAL MODULES IV. SPECIAL MODULES A. Expansion module A. Expansion module Order number : 98 28000 Order number : 98 28000 To allow more inputs than a RCVDS05 can normally accept, several RCVDS05's can be connected in series to allow swicthing of up to 90 sources. To allow more inputs than a RCVDS05 can normally accept, several RCVDS05's can be connected in series to allow swicthing of up to 90 sources.
SPECIAL MODULES SPECIAL MODULES B. COMMUNICATION INTERFACE MODULE B. COMMUNICATION INTERFACE MODULE order number : 98 28010 order number : 98 28010 When the RCVDS05's are linked or the optional IR remote receiver will be used or your RCVDS05 will be controlled by a central computer, a communication module must be installed in the slot near the output module. For typical configurations see Installation.
SPECIAL MODULES SPECIAL MODULES Switch function RS232 - BARCO Switch function RS232 - BARCO a) RCVDS05 used with BARCO projector : switch in position "BARCO". a) RCVDS05 used with BARCO projector : switch in position "BARCO". b) RCVDS05 used as stand alone unit : switch in position "BARCO". b) RCVDS05 used as stand alone unit : switch in position "BARCO".
SPECIAL MODULES SPECIAL MODULES C. 5 cable output module. C. 5 cable output module. Order number : 98 27950 All signals, Video, S-Video, RGB analog as well as Component video are transferred via 5 output BNC's. This module is designed to be used as an output module in linked RCVDS's (as replacement for the standard output module), except in the first RCVDS05. Order number : 98 27950 All signals, Video, S-Video, RGB analog as well as Component video are transferred via 5 output BNC's.
INSTALLATION INSTALLATION V. INSTALLATION V. INSTALLATION A. Power (mains) connection A. Power (mains) connection A.1. Power requirements A.1. Power requirements The power input is auto-ranging from 100 to 240 VAC 100 - 240 V 0.8 - 0.4 A 60 - 50 Hz 50 Watt The power input is auto-ranging from 100 to 240 VAC 100 - 240 V 0.8 - 0.4 A 60 - 50 Hz 50 Watt A.2. Power cord (mains lead) information. A.2. Power cord (mains lead) information.
INSTALLATION INSTALLATION A.3. Power cord connection A.3. Power cord connection Plug the male end of the power cord into an available power outlet. Plug the male end of the power cord into an available power outlet. A.4. Switching on A.4. Switching on The RCVDS05 is switched ON and OFF using the power (mains) switch ON/OFF on the front of the RCVDS05. The RCVDS05 is switched ON and OFF using the power (mains) switch ON/OFF on the front of the RCVDS05.
INSTALLATION INSTALLATION B. RCVDS05 USED AS SOURCE SELECTOR FOR A BARCO PROJECTOR. B. RCVDS05 USED AS SOURCE SELECTOR FOR A BARCO PROJECTOR. B.1. RCVDS05 to PROJECTOR communication link. B.1. RCVDS05 to PROJECTOR communication link. Plug the male D9 connector of a communication cable into the female D9 connector labelled "to projector" on the back plane of the RCVDS05.
INSTALLATION 32 B.2.2. RCVDS05 to AUDIO AMPLIFIER. B.2.2. RCVDS05 to AUDIO AMPLIFIER. Connect the left and right audio outputs (connectors below the output module) of the RCVDS05 to the left and right audio inputs of an audio amplifier using two conductor audio cables with RCA (cinch) connectors.
INSTALLATION INSTALLATION RCVDS - 1 RCVDS - 1 Mode switch in "BARCO" mode Mode switch in "BARCO" mode 98 27920 R 98 28000 L 98 27920 R R 98 28020 L R R ' I 98 27920 TO PROJECTOR R L R 98 28000 L 98 27920 98 28020 98 27930 L 98 28010 TO PROJECTOR R R L R R TO PROJECTOR L R TO PROJECTOR RCVDS - 2 RCVDS - 2 ' PDOH ' PDOH R5975765 RCVDS05 020997 33 B.4. Optional Remote IR receiver to RCVDS05.
INSTALLATION INSTALLATION by the remote IR receiver. by the remote IR receiver. Plug the male D9 connector of the communication cable into the female D9 connector on the rear of the IR remote receiver. Plug the male D9 connector of the communication cable into the female D9 connector on the rear of the IR remote receiver. Plug the female D9 connector of the communication cable into the male D9 connector labelled "to next device" on the face of the RCVDS05 communication module.
INSTALLATION INSTALLATION C. RCVDS05 USED AS STAND ALONE SWITCHER. C. RCVDS05 USED AS STAND ALONE SWITCHER. C.1. Signal connection. C.1. Signal connection. C.1.1. RCVDS05 to DISPLAY. C.1.1. RCVDS05 to DISPLAY. Connect the video output of the RCVDS05 to the video input of the display using a coaxial cable with BNC connectors. Connect the video output of the RCVDS05 to the video input of the display using a coaxial cable with BNC connectors.
INSTALLATION 36 C.1.2. RCVDS05 to AUDIO AMPLIFIER. C.1.2. RCVDS05 to AUDIO AMPLIFIER. Connect the left and right audio outputs (connectors below the output module) of the RCVDS05 to the left and right audio inputs of an audio amplifier using two conductor audio cables with RCA (cinch) connectors.
INSTALLATION INSTALLATION RCVDS - 1 RCVDS - 1 Mode switch in "BARCO" mode 98 27920 R 98 28000 L 98 27920 R R L R R ' I 98 27920 TO PROJECTOR R L R 98 28000 L 98 27920 98 28020 98 27930 L 98 28010 98 28020 Mode switch in "BARCO" mode TO PROJECTOR R R L R R TO PROJECTOR L R TO PROJECTOR RCVDS - 2 RCVDS - 2 ' PDOH R5975765 RCVDS05 020997 37 C.3. Optional Remote IR receiver to RCVDS05.
INSTALLATION INSTALLATION Plug the male D9 connector of the communication cable into the female D9 connector on the rear of the IR remote receiver. Plug the male D9 connector of the communication cable into the female D9 connector on the rear of the IR remote receiver. Plug the female D9 connector of the communication cable into the male D9 connector labelled "to next device" on the face of the RCVDS05 expansion module.
INSTALLATION INSTALLATION D. RCVDS05 USED AS HIGH BANDWIDTH SIGNAL SPLITTER. D. RCVDS05 USED AS HIGH BANDWIDTH SIGNAL SPLITTER. D.1. Use of multiple output modules. D.1. Use of multiple output modules. The RCVDS05 can be equipped with maximum 4 output modules. The selected input signal will be splitted to each output module. The RCVDS05 can be equipped with maximum 4 output modules. The selected input signal will be splitted to each output module. D.2. Signal connection. D.2. Signal connection. D.
INSTALLATION INSTALLATION RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display 1 using coaxial cable with BNC connectors. RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display 1 using coaxial cable with BNC connectors. Repeat these connections respectively for output module 2 to display 2, output module 3 to display 3 and output module 4 to display 4.
INSTALLATION INSTALLATION To Video input projector TO NEXT DEVICE BARCO 5 RS 232 / To RGBHV input projector TO HOST 98 28020 98 27930 5 S-VIDEO V 8 7 3 8 7 / VIDEO H/ C 6 7 $ 1 ' $ 5 ' 2 COMMUNICATION INTERFACE B V 5 S H/ C 98 27920 98 28010 72 352-(&725 B-Y B & 2 0 3 2 1 ( 1 7 9 ,' ( 2 , 1 3 8 7 G Y G 3 8 7 R R-Y R 5 5 * % / ( 9 ( / 6 < 1 & , 1 TO NEXT DEVICE BARCO / RS 232 V 98 28020 98 27930 5 S-VIDEO H/ C / VIDEO B V 8 7 3 8 7 To RGBHV input
INSTALLATION Plug the female D9 connector of a serial cable into the male connector of the serial port of your computer. Plug the female D9 connector of a serial cable into the male connector of the serial port of your computer. All RS232 commands have to be sent to the projector. Only the comandfor the projector can be used.
INSTALLATION INSTALLATION To RGBHV input To S-Video input To Video input D9 1 2 3 4 5 6 7 8 20 22 3 2 7 8 6 5 1 4 9 To RGBHV input Prot.
INSTALLATION 44 a 4-wire coaxial cable with 4 pin plugs. a 4-wire coaxial cable with 4 pin plugs. Connect the Red, Green, Blue, H/S sync and V sync outputs of the RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display using coaxial cable with BNC connectors. Connect the Red, Green, Blue, H/S sync and V sync outputs of the RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display using coaxial cable with BNC connectors. E.3.2. RCVDS05 to AUDIO AMPLIFIER. E.3.2.
INSTALLATION INSTALLATION RCVDS - 1 RS 232 TO NEXT DEVICE BARCO S-VIDEO / TO HOST VIDEO COMMUNICATION INTERFACE V V ' PDOH Mode switch in position "RS232" ' IHPDOH 98 28010 72 3 5 2 - ( & 72 5 5 On TO NEXT DEVICE BARCO 5 RS 232 / TO HOST V 5 S-VIDEO H/C S 98 28020 98 27930 / VIDEO B B-Y 6 7 $ 1 ' $ 5 ' 2 8 7 3 8 7 COMMUNICATION INTERFACE G Y V & 2 0 3 2 1 ( 1 7 9 , ' ( 2 , 1 3 8 7 98 27920 5 R R-Y H/C R5975765 RCVDS05 020997 H/C H/C B ( 9 ( / 6 < 1 &
INSTALLATION INSTALLATION E.4.3. Signal connection between multiple RCVDS's multiple displays. E.4.3. Signal connection between multiple RCVDS's multiple displays. No expansion module must be installed in the RCVDS's. The switch on each communication module must be set in the position 'RS232'. No expansion module must be installed in the RCVDS's. The switch on each communication module must be set in the position 'RS232'. Example : 2 RCVDS's with 2 displays. Example : 2 RCVDS's with 2 displays.
INSTALLATION INSTALLATION The output signals on the output module of the first RCVDS05 are connected to the inputs of the first display. The output signals on the output module of the second RCVDS05 are connected to the inputs of the second Display. As each RCVDS05 has a unique address, the computer can order each RCVDS to display a different source. The output signals on the output module of the first RCVDS05 are connected to the inputs of the first display.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS VI. OPERATING INSTRUCTIONS VI. OPERATING INSTRUCTIONS A. ON/OFF switching A. ON/OFF switching The RCVDS05 is switched ON and OFF using the power (mains) switch ON/OFF on the front of the RCVDS05. The RCVDS05 is switched ON and OFF using the power (mains) switch ON/OFF on the front of the RCVDS05.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS C.1. One RCVDS05. C.1. One RCVDS05. The RCVDS05 counts its own inputs (free and occupied slots) starting with slot 1 (left most slot when viewing the backside). Each empty slot before the last occupied slot will be counted by the RCVDS05 as one source number. The RCVDS05 counts its own inputs (free and occupied slots) starting with slot 1 (left most slot when viewing the backside).
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Second example : RCVDS05 equiped with the same modules as in example one, but the module in slot 4 is removed. Second example : RCVDS05 equiped with the same modules as in example one, but the module in slot 4 is removed.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Example one : Double RCVDS05 with the following input slots. RCVDS - 1 slot 1 : RGB analog input module slot 2 : Video/S-Video input module slot 3 : RGB analog input module slot 4 : expansion module Example one : Double RCVDS05 with the following input slots.
OPERATING INSTRUCTIONS RCVDS - 2 9 8 2791 0 L R 98 2 7900 L 9 8 2791 0 L R slot 1 : slot 2 : R RGB analog input module RGB analog input module 9 8 2 791 0 RCVDS - 2 R 98 2 801 0 98 280 20 98 28 000 L R L R L R L R L R L R L R L R L L R L R L R L R L R L R L R L R L 98 2 7910 L OPERATING INSTRUCTIONS R 9 8 2791 0 TO PROJE CTOR L 98 280 20 R L 52 slot RGB analog S-Video 2 (1) Video RGB analog no source4 (1) no source5 (1) no source6 (1) RGB analog
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS D. OPERATING THE RCVDS05 WITH THE BUTTON PANEL OR RCU. D. OPERATING THE RCVDS05 WITH THE BUTTON PANEL OR RCU. The controls on the button panel of the RCVDS05 are : - source selection - analog image setting - stand by switching - text on/off - pause function - audio pre-fading The controls on the button panel of the RCVDS05 are : - source selection - analog image setting - stand by switching - text on/off - pause function - audio pre-fading D.1.
OPERATING INSTRUCTIONS If there are more than 10 sources connected to the RCVDS05 (max. 20 sources possible): When selecting a source between 2 and 9, key in the corresponding number with the numeric keys. When selecting a source between 10 and 20: key in the first digit and enter the second digit within two seconds to select the corresponding source number. When the second digit is not entered within two seconds, source 1 or 2, corresponding to the entered digit will be selected.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS continue with 7. Or enter 7 and wait two seconds, source 7 will selected. continue with 7. Or enter 7 and wait two seconds, source 7 will selected. Example 2 : source 17 Enter 1, the display shows : Example 2 : source 17 Enter 1, the display shows : Enter 7 within two seconds, the corresponding source will be selected. Enter 7 within two seconds, the corresponding source will be selected.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS D.3. STAND BY D.3. STAND BY To go to stand by : press the stand by button (stby) once. All RCVDS05's will display '-'. To go to stand by : press the stand by button (stby) once. All RCVDS05's will display '-'. 67%< 3$86( 7(;7 ADJ EXIT ADDR (17(5 67%< 3$86( 7(;7 21 2)) PAUS E Button panel RCVDS05 TEXT ADDR (17(5 STBY PAUS E Button panel RCVDS05 RCU Restart : Press stand by key : last selected source will be displayed.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS When text is ON, a bar scale and number indication will be displayed when activating an image control. When text is OFF, no indication will be displayed on the screen when activating an image control. When text is ON, a bar scale and number indication will be displayed when activating an image control. When text is OFF, no indication will be displayed on the screen when activating an image control. D.5. PAUSE D.5.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Proceed as follow : - Select a source. - Adjust the audio pre-fading with the "+" and "-" pre-fading button. The adjusted level will be memorized by the RCVDS05 and recalled every time this source is selected. Proceed as follow : - Select a source. - Adjust the audio pre-fading with the "+" and "-" pre-fading button. The adjusted level will be memorized by the RCVDS05 and recalled every time this source is selected.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Where the CHKS is : (ADDR + CMD + DAT1 + DAT2 + DAT3 + DAT4)MOD256. Where the CHKS is : (ADDR + CMD + DAT1 + DAT2 + DAT3 + DAT4)MOD256. Only the least significant byte (MOD256) of the sum (ADDR + CMD + DAT1 + DAT2 + DAT3 + DAT4) is used for the checksum. Only the least significant byte (MOD256) of the sum (ADDR + CMD + DAT1 + DAT2 + DAT3 + DAT4) is used for the checksum.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS correctly. Therefore, the communication works with an ackowledge protocol using the standard ASCII bytes ACK and NAK (06H and 15H). This protocol is only active for communication from computer to RCVDS05. For communication from RCVDS05 to computer, there is no acknowledgement available. However there is only communication in this direction after a request is sent from the computer to the RCVDS05.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS The available commands : The available commands : ADDR STDBY NUM_0 NUM_1 NUM_2 NUM_3 NUM_4 NUM_5 NUM_6 NUM_7 NUM_8 NUM_9 SAT_UP SAT_DN HUE_UP HUE_DN SHA_UP SHA_DN VOL_UP VOL_DN ADDR STDBY NUM_0 NUM_1 NUM_2 NUM_3 NUM_4 NUM_5 NUM_6 NUM_7 NUM_8 NUM_9 SAT_UP SAT_DN HUE_UP HUE_DN SHA_UP SHA_DN VOL_UP VOL_DN 01HAddress RCVDS is displayed on RCVDS 0EH Standby 10HNumeric keys 11H " 12H " 13H " 14H " 15H " 16H " 17H " 18H " 19H " 2CH Color saturation up 2DH Color sa
OPERATING INSTRUCTIONS 62 "Category II" commands. "Category II" commands. CatII commands are commands which are not possible with the RCU. CatII commands are commands which are not possible with the RCU. READ_SOURCE READ_SOURCE 4AH 4AH The RCVDS05 will return to the currently selected source and source type. The DAT1, DAT2, DAT3, DAT4 transmitted to the RCVDS05 must be zero. The RCVDS05 will return to the currently selected source and source type.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS READ_POT READ_POT 7AH 7AH Reads the indicated EEPROM-value of the current selected source. The EEPROM value may be prefading, sharpness, hue (tint) or saturation. Reads the indicated EEPROM-value of the current selected source. The EEPROM value may be prefading, sharpness, hue (tint) or saturation.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS DAT4 1 RCVDS05 only answers ACK or NACK. DAT4 1 RCVDS05 only answers ACK or NACK.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS BLOCK TRANSFER EEPROM to PC BLOCK TRANSFER EEPROM to PC 72H 72H Send all the used bytes in the EEPROM to the PC (168 bytes) Send all the used bytes in the EEPROM to the PC (168 bytes) PC to RCVDS : PC to RCVDS : STX OFFS ADR 72H FFH FFH FFH FFH CHKS STX OFFS ADR 72H FFH FFH FFH FFH CHKS +OFFS +OFFS RCVDS to PC : ACK ADR 72H FFH FFH FFH FFH CHKS then 168 bytes (block) are sent CHKS after the 168 bytes.
OPERATING INSTRUCTIONS READ_VERSION OPERATING INSTRUCTIONS 4CH READ_VERSION 4CH Reads the software version of the EEPROM of the RCVDS05. Reads the software version of the EEPROM of the RCVDS05.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS DAT1 DAT2 DAT3 DAT4 1 1 2 0 0 DAT1 DAT2 programming the output module programming for Video programming for S-Video DAT3 DAT4 1 1 2 0 0 programming the output module programming for Video programming for S-Video Example : 3 RCVDS05's linked and connected to one display, no decoder installed. The mode switches are set in the RS232 mode.
ERROR CODES ERROR CODES VII. ERROR CODES 68 During operation, the RCVDS05 can display several error codes on its seven segment display. During operation, the RCVDS05 can display several error codes on its seven segment display. The F error codes ask for an intervention by the operator himself. The F error codes ask for an intervention by the operator himself. The E error codes ask for a service intervention by your dealer. Call your BARCO dealer for technical assistance.
ERROR CODES ERROR CODES Error E6 : I²C error, TDA4670, call for technical assistance (decoder module). Error E6 : I²C error, TDA4670, call for technical assistance (decoder module). Error E7 : I²C error on decoder interface. Error E7 : I²C error on decoder interface.
OPTIONAL DECODER OPTIONAL DECODER VIII. OPTIONAL DECODER. VIII. OPTIONAL DECODER. Order number : 98 28030 A decoder can be installed for Video, S-Video or Component Video decoding. All signals are converted into RGB. The decoder must always be installed in the master RCVDS05. So, in a multiple RCVDS05 installation, only one decoder has to be installed. A decoder can be installed for Video, S-Video or Component Video decoding. All signals are converted into RGB.
