VISION 508 R9002130 R9002139 OWNER'S MANUAL
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, December 1998. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco at the web : http://www.barco.
BARCO PROJECTION SYSTEMS VISION 508 R9002130 R9002139 OWNER'S MANUAL Date : 071298 Rev : 02 Art. No.
Table of Contents i TABLE OF CONTENTS TABLE OF CONTENTS .......................................... I-1 SAFETY INSTRUCTIONS ...................................... 1-1 On safety .................................................................................... 1-1 On installation ............................................................................. 1-2 On servicing ............................................................................... 1-2 On cleaning .....................................
Safety Instructions 1 SAFETY INSTRUCTIONS Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment.
Safety Instructions A. Mains lead (Power cord) with CEE 7 plug: tions: The wires of the mains lead are colored in accordance with the following code. a. When the power cord or plug is damaged or frayed. Green and yellow:earth (safety earth) Blue: neutral Brown: line (live) B. Power cord with ANSI 73.11 plug: The wires of the power cord are colored in accordance with the following code. Green/yellow:ground White: neutral Black: line (live) 3. Do not allow anything to rest on the power cord.
Location and Functions of Control 2 LOCATION AND FUNCTIONS OF CONTROL Rear Panel Terminology 1 2 3 4 11 7 8 12 9 5 6 1 Communication port (800 peripherals) allows communication between the RCVDS switcher and the projector. allows connection of a remote IR receiver unit to the projector. 2 IR Remote - Remote input for wired remote control 3 IR sensor RCU. 4 RGB-S IN or (R-Y)Y(B-Y)-S IN (4x BNC connector): RGB-S in : allows a character generator, video camera, etc.
Location and Functions of Control Control panel terminology a. The local keypad Gaining access The local keypad is at the rear side of the projector. b. RCU control panel terminology This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing of : - picture controls (Brightness, Sharpness,....
Location and Functions of Control 1 BARCO key : When a RF-tuner is built in (option), this key used to toggle between Video and tuner signal. 2 ADJ. : adjust key, to enter or exit the adjustment mode. 3 Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the address key, followed by pressing one digit button between 0 and 9. 4 STBY : stand by button : - to initiate remote power up operation - to stop projection without main power off.
Connections 3 CONNECTIONS Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the rear of the projector. 120/230 V 4/2.5 A 60/50 Hz 300 W Switching on/off The projector is switched ON and OFF using the power (mains) switch ON/OFF. Stand by indication lamp : No light up : Projector in operational mode Red : Projector is in stand by.
Connections Connecting a Composite Video source. Composite video signals from a VCR, OFF air signal decoder, etc.. Composite video Audio amplifier TV tuner, e.g. TVDM40 stereo Video input selection : a. with the RCU : press digit button 1 or VCR b. with the local keypad. - press ADJUST key, the General access menu is displayed on the screen. - use the control disc to highlight 1. - press ENTER to select the highlighted source.
Connections Input selection a. with the RCU : press digit button 2 or b. with the local keypad. - press ADJUST key, the General access menu is displayed on the screen. - use the control disc to highlight 2. - press ENTER to select the highlighted source. GENERAL ACCESS 5 3 1 6 4 2 7 SHARPNESS TINT COLOR BRIGHTNESS CONTRAST Enter ADJUST Select with , or then . to return Connecting a RGB Analog source with composite sync.
Connections Connecting a Component source. YUV analog input terminals with sync input or with sync on the luminance (Y) input. Professional VCR Audio amplifier YsUV or YUVS input selection a. Press digit button 6 (for YsUV) or 7 (for YUVS) on the RCU or GENERAL ACCESS b. With the local keypad : 5 3 1 - Press ADJUST key, the General access menu is displayed on the screen. - Use the control stick to highlight 6 (7 for YUVS). - Press ENTER to select the highlighted source.
Connections Connecting an external audio signal to the projector: (optional) Connect an external audio signal the audio input of projector is only possible when the tuner option is installed. Connect your external source to the audio input (2 x cinch connector). Connect external loudspreakers (Left and right) to the loudspeaker outputs of the projector. Connecting speakers wires. Peel back the vinyl covering and twist the wire core.
Controlling 4 CONTROLLING Caution : Do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the CRT's. Battery installation in the RCU. A new battery is delivered inside the plastic bag with the power cord. Before using the RCU, install first the battery. Remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig.
Controlling c) RCU used in a hardwired configuration. The projector can be controlled with a. The RCU b. The hardwired RCU (cable not included) c. The local keypad. Controlling the projector with the RCU and the hardwired RCU is the same.
Controlling To continue using the RCU, it is necessary to enter an address with the digit buttons (address between 0 and 9). For example : if the Address key displays projector address 003, the press "3" digit button on the RCU to set the RCU's address to match the projector's address. Do not press digit 003. This will address the remote to '0' and control all projectors in the room.
Controlling Picture controls The picture controls can be adjusted with : a) The RCU. The control keys are located on the left side of the key panel of the RCU and indicated with the name of the control and an icon. When an image control is pressed, a text box with bar scale and the function name of the control, e.g. 'brightness...' appears on the screen (only if text is ON). The length of the bar scale indicates the current memorized setting for this source.
Controlling Sound control with the RCU (optional). Only available when the tuner option is installed. When an analog sound control is pressed, a bar scale and a number below the bar scale appear on the screen with name of the control, e.g. 'Volume' above it. The lenght of the bar scale and the number indicate the current setting for this source. The bar scale changes as the + or - buttons of the control are pressed.
Start Up of the Adjustment Mode 5 START UP OF THE ADJUSTMENT MODE Adjustment mode All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Two possible ways to enter the adjustment mode : a) Using the RCU. Press the ADJUST key. The projector displays the path selection menu. b) Using the local keypad. Press the ADJUST key. The projector displays the General access menu. $'-867 (;,7 67$1'%< (17(5 Use the control disk to highlight enter ADJUST and press ENTER.
Start Up of the Adjustment Mode RANDOM ACCESS - Random Access should be selected if the user intends to make only a few adjustments. SERVICE - Service should be selected if the user intends to delete blocks, change password or apply information. While in Guided or Random Access adjustment Mode, the user may use an external source, an internally generated genlocked pattern or an internally generated multifrequency cross hatch pattern as a setup pattern. Warning during the start up of the installation mode.
Random Access Adjustment Mode 6 RANDOM ACCESS ADJUSTMENT MODE Starting up the random access adjustment mode. Push the control disc up or down to highlight "RANDOM ACCESS" and then press ENTER. ADJUSTMENT MODE Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode.
Random Access Adjustment Mode Selecting Setup Pattern If an external source is connected to the projector, this menu will be displayed. Push the control disc up or down to highlight the desired setup pattern and then press ENTER. Genlocked pattern : internally generated cross hatch pattern, locked on the external source. Internal # pattern : internally generated cross hatch pattern and locked on internal generated sync signals.
Random Access Adjustment Mode Color Balance The Color Balance function is used to select or adjust the color temperature of white used by the projector. The Color Balance can be adjusted on two different ways : - fixed color balance. You have the choice between 3200 K (reddish), 4900 K, 6500 K (white) or 9300 K (bluish). - Custom white and black balance. Fixed Color Balance. Highlight one of the 4 preprogrammed color temperatures with the control disc and press ENTER to display the desired color balance.
Random Access Adjustment Mode Color Select Highlight COLOR SELECT by pushing the control disc up or down and press ENTER to display the color select menu. ENTER continues to the color select menu. EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu. ADJUST returns to operational mode. Use the control disc to highlight a color (CRT) or combination of colors to display the projected image in that specific color.
Random Access Adjustment Mode Horizontal Phase Adjustment GEOMETRY Push the control disc up or down to highlight H PHASE on Geometry menu and then press ENTER. H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) H SIZE V LINEARITY V SIZE BLANKING Select with or then to return. Note : No horizontal phase adjustment is available on the internal # pattern. For external sources : If the raster shift is correctly adjusted, the H Phase text box is projected in the middle of the raster.
Random Access Adjustment Mode forbidden area Warning : In order to ensure maximum CRT longevity and to avoid CRT damage, do not shift the raster outside the phosphor area of the CRT. To start the adjustment, use the control disc to highlight Raster shift and press ENTER to display the green raster on the phosphor. projected raster crt faceplate border phosphor border correct raster position wrong raster position Press EXIT to return to the Geometry menu.
Random Access Adjustment Mode Left-Right (east-west) Adjustments Left-right and center adjustments affect only the vertical lines of the projected image. GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) H SIZE V LINEARITY V SIZE BLANKING To start up the left-right and center adjustments, follow the next procedure : Push the control disc up or down to highlight LEFT-RIGHT (E/W) on the geometry menu and then press ENTER.
Random Access Adjustment Mode Top-Bottom (north-south) Adjustments Top-Bottom and center adjustments affect only the horizontal lines of the projected image. To start up the Top-Bottom and center corrections, follow the next procedure : Push the control disc up or down to highlight TOP-BOTTOM (N/S) on the geometry menu and then press ENTER. Only the green image is displayed while making top-botton adjustments. The red and blue images will automatically be corrected in the same manner.
Random Access Adjustment Mode Horizontal Size Adjustment Push the control disc up or down to highlight H SIZE on the Geometry menu and then press ENTER. GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) H SIZE V LINEARITY V SIZE BLANKING ENTER will select horizontal size adjustment. EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode. Adjust the horizontal size by pushing the control disc to the right or to the left until the exact image width is obtained.
Random Access Adjustment Mode Horizontal Size Adjustment Push the control disc up or down to highlight V SIZE on the Geometry menu and then press ENTER. GEOMETRY H PHASE RASTER SHIFT LEFT-RIGHT (E-W) TOP-BOTTOM (N-S) H SIZE V LINEARITY V SIZE BLANKING ENTER will select vertical size adjustment. EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode. Adjust the horizontal size by pushing the control disc to the right or to the left until the exact image width is obtained.
Random Access Adjustment Mode Adjust the next blanking alignments until the image is correctly framed or the unwanted information is blanked out. To enter a blanking alignment, push the control disc up or down to highlight a function and press ENTER to activate this function. Press EXIT to return. Adjustment of the blanking on the of the image BLANKING TOP BOTTOM LEFT RIGHT Select with or then to return.
Random Access Adjustment Mode Convergence Adjustment Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE COLOR SELECT Note : the green convergence adjustments can be added as an option. When these are available, start always with 'green only'.
Service Mode 7 SERVICE MODE Starting up the Service mode. Use the control disc to highlight 'Service' and then press ENTER. Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode. ENTER continues to the Service Mode main menu. EXIT returns to the Operational mode.
Service Mode Projector Set-up Highlight 'Projector Set-Up' by pushing the control disc up or down and press ENTER to display the projector set-up menu.
Service Mode Total Run Time Highlight 'Total Run Time' with the control disc and press ENTER to display the amount of time the projector has played since its first start up at the factory. PROJECTOR SET-UP IDENTIFICATION TOTAL RUN TIME CHANGE PASSWORD CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE : operating ENTER gives the selected item. EXIT returns to the Service mode menu. ADJUST returns to the Operational mode. Select with or then to return.
Service Mode Change baudrate The communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up. Highlight 'Change Baudrate' by pushing the control disc up or down and press ENTER to display the Baud rate menu. The following baud rates are available : - 9600 4800 2400 1200 600 300 150 110 The actual baud rate will be highlighted.
Service Mode Copy a block The copy a block function copies the settings of a selected block into the active block. Highlight copy a block with the control disc and press ENTER. ENTER will select the highlighted item. EXIT returns to the Path Selection main menu. ADJUST returns to the Operational mode. To copy the settings of a closed block to the block you are working on (active block), use the control disc to select a block. All existing settings will be overwritten with the new settings.
Service Mode Deletion of all blocks MEMORY MANAGEMENT Highlight 'delete all blocks' with the control disc and press ENTER. ENTER gives a confirmation message before deleting. EXIT returns to the Path Selection main menu. If you are certain you wish to delete all blocks, press ENTER to confirm, otherwise press EXIT to return. Once ENTER is pressed, all block headers and adjustment settings are permanently removed and cannot be restored.
Service Mode R & B convergence mid Item is password protected. Highlight 'R & B convergence mid' with the control disc and press ENTER to set all convergence settings to their midposition. A confirmation screen will be displayed first. ENTER sets the convergence settings to their midposition. EXIT cancels the procedure to set the convergence settings to their midposition.
Service Mode Common Settings Highlight 'Common settings' by pushing the control disc up or down and press ENTER to display the common settings menu. Within the common settings menu, the following items can be set up or executed : - G2 adjustment - CRT run in cycle SERVICE MODE PROJECTOR SET-UP MEMORY MANAGEMENT COMMON SETTINGS I2C DIAGNOSTICS Select with or then to return. COMMON SETTINGS G2 ADJUSTMENT CRT RUN IN CYCLE Select with or then to return.
Service Mode the CRT run in cycle will start when pressing ENTER. If no such a block is available, the projector cannot run the CRT run in option and leaves the adjustment mode. If you still want to run CRT run in cycle, create first a memory block on an internal # pattern and restart the CRT run in option. ENTER starts the 'CRT run in' when an internal generated # pattern is available. EXIT returns to the Path Selection main menu.
Options 8 OPTIONS IR Receiver 800 VS05 Switcher This infrared receiver unit makes it possible to control the projector from another room. There is a communication line with cable between the IR receiver and the projector or the RCVDS05. The control information from the RCU can now be sent to this IR receiver. The IR receiver 800 displays the selected source on a 7-segment display.
Options Tuner kit With one of the four available tuner kits, it is possible to receive RF signals from a TV cable network or a TV antenna. The four kits are designed to fulfil the different broadcasting systems worldwide.
Tuner Mode A TUNER MODE Tuner mode With one of the four available tuner kits, it is possible to receive RF signals from a TV cable network or a TV antenna. The four kits are designed to fulfil the different Broadcasting systems worldwide. These kits are : Order n o.
Tuner Mode The projector displays the General access menu. Use the control disk to highlight TUNER and press ENTER. The last selected channel will be displayed. To switch to another channel, push the control disc up or down. GENERAL ACCESS 5 3 1 6 4 2 7 TUNER SHARPNESS TINT COLOR BRIGHTNESS CONTRAST Enter ADJUST Select with , or then .
Tuner Mode Auto Search All channel information will be overwritten and the channel list will be reorganised completely. The projector scans the entire VHF and UHF band for the available TV frequencies. It starts in the lower frequency range and it stores each found frequency in another preselection in a consecutive order. It takes around 2 to 3 minutes to complete the entire TV spectrum. To start auto search, push the control disc up or down to select the 'Auto Search' function and press ENTER to select.
Tuner Mode Organise Channel List Once the TV frequencies are entered in the channel list, this list can be ordered according your own preferences. Highlight 'Organise Channel List' by pushing the control disc up or down and press ENTER to select. The channel list will be displayed. To reorganise the channel list : - select a frequency with the control disc. - press ENTER to copy this frequency to the clipboard. - select the new location with the control disc.
Tuner Mode Teletext This teletext function is only available when operating in tuner mode. To enter the teletext mode, press the TEXT key. The following keys on the RCU has a function in the teletext mode : TEXT : a 3 way toggle key Teletext OFF Video ON Teletext ON Video OFF Teletext ON Video ON NUM key (0 ...9) To enter directly the page numbers (3 digits), e.g. 730, press the digit 7-3-0 successively. The number of the chosen page will appear in the top left-hand corner of the screen.
Insert Card INSERT CARD 5&8 ,1 3 8 7 6 2 8 5 & ( 6 35 2 -( & 72 5 & R P S 9 LG H R 6 9 LG H R 5 * V% 5*%6 < V8 9 < 8 96 , 1 3 8 7 6 2 8 5 & ( 6 5 & 9' 6 5&8 ,1 3 8 7 6 2 8 5 & ( 6 3 5 2 -(& 72 5 3 3 , 1 3 8 7 6 2 8 5 & ( 6 5 & 9' 6 " 5975039 BARCOVISION 508 100698 i-1
