ImagePRO-II Dual Output User’s Guide Addendum • Manual #: 26-0904001-00 • Revision: 00
User’s Guide Addendum Copyright © Barco. June 12, 2012 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. Notice Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose.
Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.
Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
Change History The table below lists the changes to the User’s Guide Addendum. Rev Date ECP # 00 6/22/12 597847 26-0904001-00 Rev 00.00 Description Initial Release Approved By R.
Table of Contents Introduction.......................................................................7 1. Getting Started ..............................................................7 2. Initial Setup ...................................................................7 To enable Dual Channel Mode ................................................................................... 7 Setting up the Output Connector Map ........................................................................ 8 3.
Introduction ImagePRO-II’s Dual Channel Output mode, available in the ImagePRO-II Dual Output unit, allows for any selected input or Logo to be presented at two different output resolutions simultaneously. For example, say your main presentation output is a projector running at 1920x1080p. With this mode enabled you could also send the output to a record deck expecting NTSC.
Setting up the Output Connector Map Now that Dual Channel mode is enable, select which output connectors will map to Output A and which will map to Output B. 1) Within the SYSTEM menu, scroll to and select the OUTPUT CONNECTOR MAP submenu 2) By default, all seven outputs of the ImagePRO-II will be mapped to Output A. 3) Scroll to the various connectors as required and change the field from A to B to map that connector to Output B.
3. Output Configuration Once the mode and connectors have been setup, specific configuration of the two outputs can be performed. Output Resolution 1) In the OUTPUT setup menu, the first two lines (labelled CHA and CHB) show the current resolution and frame rate for each channel. 2) Select either of these menu items to change the output resolution / frame rate to the desired choice. Area of Interest 1) Select the AREA OF INTEREST submenu under OUTPUT.
Output Effects 1) Select the EFFECTS submenu under OUTPUT. 2) The first field (labelled CHANNEL) allows the selection of A, B or ALL to allow for independent or simultaneous adjustments for each output. Genlock 1) Select the GENLOCK submenu under OUTPUT. 2) The first field (CHA SOURCE) can be selected and will offer all the standard Genlock source options (FREERUN, EXT or IN #). 3) The second field in the menu (CHB SOURCE) will default to LOCK TO A.
Save and Reset Output Configs 1) Within the SAVE CONFIG and RESET CONFIG submenus under OUTPUT, the first field allows for the selection of A, B or ALL. Make the appropriate selection when saving or resetting output configurations. Pan / Zoom 1) Select the PAN/ZOOM button on the front panel of the ImagePRO-II. 2) The first field (labelled CHANNEL) allows the selection of A or B to allow independent Pan and Zoom adjustments for each output channel.
4. General Operation 1) In addition to the input and output connectors provided in ImagePro-II, the ImagePro-II Dual output unit provides a second SDI input (SDI 6) and associated loop-through as well as a second SDI output (SDI 2 OUT). 2) When switching from Single mode to Dual2K mode, the user will be prompted to take corrective action if the following items are not setup correctly. Until these items are corrected, the unit will not be allowed to enter Dual2K mode. a.
5. Remote Commands The following commands have been updated as of software release 02.00.02. ICH Description: Input Channel Settings Required parameters: --con (connector) --ch (channel) --itype (input type), only for commands to DVI connector Parameters: --con (connector) : 0-5, see below for input connector numbers.
Query Format 2 (Input window): ICH --con (connector) --ch (channel) --iwin --? Query Response 2 : Input Channel Window Setting in the following format ICH --hpos (H Position) --vpos (V Position) --hsize (H Size) --vsize (V Size) Query Format 3 (Mask): ICH --con (connector) --ch (channel) --mask --? Query Response 3 : Input Channel Mask Setting in the following format ICH --left (Left) --right (Right) --top (Top) --bottom (Bottom) Connectors: 0=DVI 1=HD15 2=HDMI 3=DP 4=SDI1 5=SDI2 (available when Dual optio
STMGR Description: Logo Management Settings Parameters: --deleteall --eraseall --captureall --infoall : Delete logo : Erase logo (destructive) : Capture logo : Logo H/V information Query Format: n/a OCON Description: Output Connector Settings Required parameters: --ocon (output connector) Parameters: --ocon (output connector) --ch (channel select) --syncpol (sync polarity) --bitdepth (color bit depth) --csp (color space) , for output connectors : 0-6, see below for connector numbers.
SYSMGR Description: System Manager Settings Parameters: --blkinv (Black Invalid Mode) --vfd (VFD Brightness) --opmode (Operation Mode) : 0=OFF, 1=ON : 0..6 : 0=SingleChannel, 1=DualChannel, 2=3DProcessing Note: For the new operating take full effect, you must save settings and reboot the unit. --conmode (Encore Connect Mode) : 0=OFF, 1=ON --unitid (Encore Unit ID) : 1..32 --encoreip (Encore IP address) : xxx.xxx.xxx.
VFS Description: Video Format Settings Required parameters: --con (connector) --och (output channel) --itype (input type) , for input video format , for output video format , for commands to DVI Input settings Parameters: --con (connector) : 0-5, see below for input connector numbers. --och (output channel) : 0-1, for output commands --itype (input type) : 0 = digital, 1 = analog --new (new format name) : Use "" around the format name. Use VFSTDLIST to get the standard format names.
Parameters: --con (connector) : 0-5, see below for connector numbers. --och (output channel) : 0-1 --itype (input type) : 0 = digital, 1 = analog --brt (overall brightness) : [50..150] --cbrt (individual brightness) : [50..150] --cnt (overall contrast) : [50..150] --ccnt (individual contrast) : [50..150] --col (color) (must be supplied for --cbrt or --ccnt parameters) 0 = all color 1 = red 2 = green 3 = blue --sat (saturation) : [0..125] --hue (hue) : [-90..
--ch (channel) :0-1, input channel --units (units) :0 = percent, 1 = pixel --percent :if values are given in percent, See PANZOOM --help for parameter details --pixel :if values are given in pixel, See RECT --help for parameter details --save (save view settings) --recall (recall view settings) --reset (reset view settings) Query Format 1 (Unit): VIEW --con (connector) --ch (channel) --? Query Response 1: View Settings in the following format VIEW --unit (units) Query Format 2 (percent values): VIEW --con (
