PMP kit Installation manual Galaxy NH-12, NW-12, Galaxy NW-12 R7649672K R7649676K R59770498/01 28/02/2011
Barco nv Simulation Division Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.84.86 E-mail: info@barco.com Visit us at the web: www.barco.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors.
Table of contents TABLE OF CONTENTS 1. Safety instructions . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3 1.1 Safety during kit installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. PMP kit . .. .. .. .. .. .. .. .. .. .. .. .. .. .
Table of contents 2 R59770498 PMP KIT 28/02/2011
1. Safety instructions 1. SAFETY INSTRUCTIONS 1.1 Safety during kit installation WARNING: The procedures below may only be performed by Barco trained and qualified technicians. WARNING: Power down the projector and remove the power cord form the wall outlet before removing any of the projector covers.
1.
2. PMP kit 2. PMP KIT 2.1 Introduction Introduction In case of failure of a PMP, it must be replaced by a (blank) new one. However, since most of the projector related data is stored on this board, this data will be lost while replacing the board. This includes not only key data such as Projector Device Type and Projector Serial Number, but also the full set of factory settings of the projector which are indispensable to get a good quality image: uniformity, colors, gray levels, etc.
2.
3. Kit installation (detailed) 3. KIT INSTALLATION (DETAILED) CAUTION: This procedure may only be performed by Barco trained and qualified technicians. 3.1 Making a backup of the PMP to be replaced Introduction If a PMP fails, communication via Ethernet is most probably still possible. This implies that a backup can still be made using the Projector Support tool. If there is no more communication with the faulty PMP, Barco’s helpdesk must be contacted.
3. Kit installation (detailed) 3. Lift the preformatter unit a bit and unplug the following connectors: - J100, J101, J102 on the preformatter: data from the PMP - J11 on the preformatter: power supply from the power box - J410 on the PMP: commands from the local keypad - J13 on the PMP: commands from the IR receiver 4. Remove the screw fixing the three grounding wires 5. Flip over the preformatter unit Or, Unplug the other connectors on the preformatter unit and remove the unit 6.
3. Kit installation (detailed) How to remove the PMP? 1. Remove the input module (see concerning chapter) 2. Remove both screws fixing the PMP to the front plate Image 3-4 PMP: front fixing screws 3. Remove the side screws fixing the input boards to the PMP Image 3-5 4. Disconnect the PMP from the inputs by unplugging the board-to-board connectors Image 3-6 PMP: unplug from input boards 5.
3. Kit installation (detailed) Image 3-7 PMP: fixing screws of the LVDS interface 6. Remove the screws fixing the PMP fan assembly to the PMP Image 3-8 PMP fan assembly: fixing screws (1) 3.2.3 Image 3-9 PMP fan assembly: fixing screws (2) Installing the PMP How to install the PMP? 1. Put the PMP fan assembly on the PMP and fix it using 6 screws Image 3-10 PMP fan assembly: fixing screws (1) Image 3-11 PMP fan assembly: fixing screws (2) 2.
3. Kit installation (detailed) Image 3-12 PMP: fixing screws of the LVDS interface 3. Connect the PMP to the inputs by plugging in the board-to-board connectors Image 3-13 PMP: plug into the input board connectors 4. Fix the PMP to the input boards using the side screws Image 3-14 PMP: side screws fixing the input boards 5.
3. Kit installation (detailed) Image 3-15 PMP: front fixing screws 6. install the input module into the projector (see concerning chapter) 3.2.4 Installing the input module Necessary tools Torx screwdriver T10 How to install the input module? 1.
3. Kit installation (detailed) Image 3-17 input module: fixing front screws 4. Put the preformatter unit next to its correct position and plug in the connectors: - J100, J101, J102 on the preformatter: data from connectors J823, J824 and J825 on the PMP - J11on the preformatter: power supply from connector 6 on the power box - J410 on the PMP: commands from connector J410 on the local keypad - J13 on the PMP: commands from the IR receiver 5.
3. Kit installation (detailed) Necessary tools Computer or laptop, connected to the projector through Ethernet How to upgrade the projector software? 1. Enter the correct Ethernet settings in the OSD of the projector 2. Download the desired upgrade tool to your computer or laptop 3. Run the upgrade tool NW- x v03.01.0001.
A. Backup and restore data A. BACKUP AND RESTORE DATA Overview • Connecting to the projector through Projector Support • Making a backup of the projector’s key data • Restoring a set of key data About this chapter It is extremely important to make backups of your projector data after each setting change. This chapter describes how to use Barco’s Projector Support software tool to make a backup of the key data of a projector and how to restore this backup.
A. Backup and restore data Image A-1 Projector Support tool: user interface 4.
A. Backup and restore data Tip: You can also press the Query button. A list appears, showing all the projectors that are connected to the same network. In this list, select the desired projector and hit OK.
A. Backup and restore data Select it and hit OK to open a new window where the network settings can be manually changed. It is advised to switch DHCP to On to continue. Image A-6 Projector Support tool: change DHCP setting to ON Image A-7 Projector Support tool: confirm network settings A.2 Making a backup of the projector’s key data How to make a backup of the projector’s key data? It is assumed that communication with the projector has been established through Projector Support. 1.
A. Backup and restore data Image A-8 Projector Support tool: select browse in the Backup section 2. Select a target folder on the computer to save the backup of the projector data Image A-9 Projector Support tool: browse to the backup folder 3. Change the file name (optional) and hit Save Image A-10 Projector Support tool: change the name of the backup file (optional) 4.
A. Backup and restore data Image A-11 Projector Support tool: start the backup of all settings 5. Wait for the backup process to be finished. Image A-12 Projector Support tool: progress bar A successful backup is indicated by a green oval. Image A-13 Projector Support tool: backup successful An error is indicated by a brief description and a red oval. Solve the cause of the error and retry.
A. Backup and restore data CAUTION: It is not allowed to do any manual change to a backup file. A.
A. Backup and restore data Image A-15 Projector Support tool: browse to the backup folder 4. In the Restore section, you can select an option (not required): - Overwrite serial number - Overwrite device type Image A-16 5. In the Restore section, hit All settings Image A-17 Projector Support tool: start the restore of the backup 6.
A. Backup and restore data Image A-18 Projector Support tool: confirm the restore of the backup 7. Wait for the restore process to be finished Image A-19 Projector Support tool: progress bar Image A-20 Projector Support tool: reboot of the PMP after the restore A successful restore of the backup file is indicated by a green oval.
A. Backup and restore data Image A-21 Projector Support tool: restore of the backup was successful An error during the restore of the backup file is indicated by a brief description and a red oval. Solve the cause of the error and retry.
A. Backup and restore data Image A-22 Projector Support Tool: restore of the backup was not successful How to restore the key data in a new PMP? It is assumed that an original backup file is available (zip format). 1. Start the Projector Support tool and select Query in the Communication Parameters section of the user interface 2.
A. Backup and restore data Image A-23 Projector Support tool: query list Tip: If more then one PMP without serial number is listed, the MAC address must be checked. On the PMP board a label mentioning the MAC address can be found near the power connector on the same side as the heatsinks. 3.
A. Backup and restore data Image A-24 Projector Support tool: hit browse in the restore section 4. Browse to the folder on the computer where the backup file is stored 5. Select the backup file and hit Open 6. In the Restore section, hit All settings Image A-25 Projector Support tool: browse to the backup folder 7.
A. Backup and restore data Image A-26 Projector Support tool: overview of the files that will be restored 8.
A. Backup and restore data A successful restore of the backup file is indicated by a green oval, and the original serial number will be displayed in the Projector identification section of the user interface. Image A-29 An error during the restore of the backup file is indicated by a brief description and a red oval. Solve the cause of the problem and retry.
A.
Index INDEX B P backup 7, 15, 18 making of 18 PMP 7 PMP 7–8, 10 backup 7 installing 10 replacing 7 PMP kit 5 Projector Support 15 connecting 15 D description kit 5 5 R I removing 7–8 input module 7 PMP 8 replacing 7 PMP 7 restore 13, 15, 21 backup 13 input module 7, 12 installing 12 removing 7 installation 5, 7 kit 5, 7 installing 10, 12 input module 12 PMP 10 introduction 5 S safety K kit 5, 7 description 5 installation 5 installation (detailed) 3 U upgrade the projector 13 7 R59770498 PM
