MFCD 1219 (TS) User Manual
(This page intentionally left blank.
Copyright notice This document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco © 2006 Barco N.V. All rights reserved.
Table of Contents Table of Contents Preface ................................................................................................. 5 Environmental information.......................................................... 7 Safety Instructions........................................................................ 7 Overview............................................................................................ 10 Introduction ......................................................................
Preface Preface Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, please let us know. BarcoView software products are the property of BarcoView. They are distributed under copyright by Barco N.V. or BarcoView, LLC., for use only under the specific terms of a software license agreement between Barco N.
Preface reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Preface Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations. This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment.
Preface Electrical shock Type of protection (electrical): Class I equipment Degree of safety (flammable anesthetic mixture): Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. Power connection • Power requirements: The display must be powered using the 12 VDC power supply that is supplied with the display. • The 12 VDC power supply must be powered by the AC mains voltage.
Preface Water and moisture Never expose the display to rain or moisture. Never use the display near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry tub or in a wet basement. Ventilation Do not cover or block the ventilation openings in the cover of the set. When installing the display in a cupboard or another closed location, heed the necessary space between the set and the sides of the cupboard.
Overview Overview Introduction The MFCD 1219 (TS), BARCO’s full color 19” LCD display, guarantees perfect image quality in medical imaging applications. The display combines a TFT (thin film transistor) liquid crystal display panel structure and a built-in backlight with inverter for a better picture quality.
Overview Touch panel The MFCD 1219 TS is equipped with a touch panel. Instructions on how to install and use the touch panel driver and controls can be found in the "TouchKit, Barco TouchScreen controller installation and user manual" on the supplied CD-ROM. Package contents The package should include the following items, please check. If some of the items are missing, please contact the reseller you have purchased the unit from.
Overview Controls and connectors 11 1 2 3 4 5 6 7 8 9 10 1. 12V DC power input 2. DVI input (DVI-D supported only) 3. Analog video input 4. USB port for touch panel connection to PC (MFCD 1219 TS only) 5. < (left) Key 6. > (right) Key 7. Menu key 8. Auto Key 9. Power LED The LED is off when the display is off. The LED is green when the display is on. The LED is orange when the display is in power-saving mode (stand-by) 10.
Overview 11.
Installation Installation Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation in case it is built in a rack or console. Do not put in direct sunlight. • Make sure computer and display are switched off before connecting the signals.
Installation 2. Firmly press down the push-button (9) with one hand while carefully lifting the panel up with the other hand. 3. Remove the panel from the foot. Step 2: Fix the mounting plate to the wall 1. Screw the mounting plate to the wall with the 4 supplied screws (A). A 2. Slide back the locks at both sides of the mounting plate (B). In that way, you can secure the panel to the mounting plate after placing the panel. B Step 3: Place the panel on the mounting plate 1.
Installation Please make sure that the four shafts are securely placed in the notches of the mounting plate. C 2. To secure the panel, slide forward the locks on both sides of the mounting plate. Lock the panel with one screw at both sides (D).
Installation To connect the video & sync signals: 1. Connect one end of the appropriate video cable to the corresponding video input of the monitor. • Analog video: Connect to input (3) • DVI: Connect to input (2) 2. Connect the other end of the video cable to the video output of your video source. • Analog video: Computer graphics board with analog video output • DVI: Computer graphics board with digital video output To connect the power: 1.
Installation 1 Note: The recommended resolution for best image quality is 1280x1024 at 60 Hz. The microcontroller in the display checks if the connected video signal has been adjusted before, and if these adjustments have been stored in the memory. There are 2 possibilities: a) The video signal has been adjusted and stored in the memory. In this case, the display switches to this memory location (the socalled mode) and the image will need no further adjustments.
Installation Touch panel software: Please refer to the TouchKit installation & user manual on CD-ROM.
On-screen display (OSD) On-screen display (OSD) How to use the OSD 1 2 3 4 The OSD is a window on your screen that allows you to view and change display settings. To change an OSD setting, proceed as follows: 1. Press the Menu key (3) on the front to display the OSD main menu. Note: It may be possible that the OSD menu does not appear. If this is the case, the front Controls are locked. To unlock them, please follow the procedure described in § 3.2 below. 2. There are 5 OSD submenus divided by categories.
On-screen display (OSD) a) Press the < (left) key (1) or > (right) key (2) to change the value. b) Press the Menu key (3) to enter the new value and return to the menu. 5. The current settings are saved automatically when you return to the previous level or exit the OSD menu. 6. The Auto key (4) acts as Exit function while the OSD is on the screen. Pressing the Auto key (4) takes you back to the previous level in the OSD. Pressing the Auto key (4) while the main menu is on the screen closes the OSD. 7.
On-screen display (OSD) Function Description Contrast To adjust the image brightness in relation to the background (the background is unchanged). This function controls the digital gain adjustment. Image Control menu This menu is available only when an analog video signal is selected.
On-screen display (OSD) Function Description Phase Manually adjusts the internal clock phase. When not adjusted correctly, vertical bands with alternate intensity appear in the image.
On-screen display (OSD) OSD Control Menu OSD CONTROL H OSD POSITION V OSD POSITION OSD TIMEOUT LOCK CONTROLS > > > > Function Description H OSD Position Adjust the horizontal position of the OSD window V OSD Position Adjust the vertical position of the OSD window OSD Timeout Determine how long (in seconds) the OSD menu waits before closing automatically when no action is performed Lock Controls When you lock the controls, the OSD will not appear when you touch the control keys To unlock the Con
On-screen display (OSD) Others Menu OTHERS LANGUAGE INPUT TIMING INFORMATION Function > > > Description Language Select the OSD language Input Select the desired video input. The analog video input has priority when both analog and DVI inputs are used. Timing Information Display timing information each time the timing changes.
On-screen display (OSD) Reset Menu RESET YES NO Function 26 > > Description Yes Select his function to reset all display parameters to the factory default settings No Select this function to exit from the Reset window without resetting the settings
Maintenance Maintenance Panel Take care not to damage or scratch the panel. Clean with a soft woolen or cotton towel. Use a watery solution or a mild commercial glass cleaning solution. Cabinet Do not use chemical cleaning products, benzene, toluene, xylene or other solvents. Clean with a soft cloth dampened with mild detergent and water. Repeat this with water only and wipe dry with a dry cloth.
Appendix A: Possible resolutions Appendix A: Possible resolutions The following modes are preset as factory defaults. Resolution Pixel freq. (MHz) Hor. freq. (kHz) Vert. freq. (Hz) Standard Analog Digital 640 x 350 25.175 31.47 70 VGA V V 640 x 480 25.175 31.47 60 VGA/VESA V V 30.24 35.00 67 Mac V 31.50 37.90 72 VESA V 31.50 37.50 75 VESA V 36.00 43.30 83 VESA V 720 x 400 28.321 31.47 70 VGA V 800 x 600 36.00 35.10 56 VESA V 40.00 37.88 60 VESA V 50.
Appendix B: Technical specifications Appendix B: Technical specifications Picture panel 19-inch diagonal viewable screen TFT (thin film transistor) active matrix, color liquid crystal display, RGB interface Touch panel (MFCD 1219 TS only) Resistive technology Interface: USB 1.1 Input mode: stylus or finger Touch active force (stylus Æ 0.8 mm): <=50g Resolution 1280 x 1024 (native) Display area (H x V) 376 x 301 (mm) Pixel Pitch 0.294 mm (H) x 0.
Appendix B: Technical specifications Front panel controls Left, Right, Menu, Auto, Power Input connectors 15-pin D-sub (for PC graphic signal input) Bus Connector (for DC 12V, 4.5A input) DVI connector (supporting DVI-D only) Power source 100 ~ 240 VAC Power consumption 50 W (max.) Less than 5 W in power-off mode Power saving VESA DPMS standard PnP compatibility VESA DDC 2B standards compliant Safety standards UL60950, cUL60950, IEC60950, CE, CCC Dimensions (W x H x D) 450 mm x 461.
K5904118-00 July 2006 www.barco.
