BARCO N.V. Communication Systems Th. Sevenslaan 106 B-8500 Kortrijk (Belgium) Tel.: +32.56.233.211 Fax: + 32.56.233.461 E-mail: support.bcs@barco.com Web site: http://www.barco.
HDM 5049 PLUS Contents Contents 1 SAFETY INSTRUCTIONS.............................................................................1-1 1.1 1.2 1.3 FCC NOTICE .....................................................................................................................1-1 POWER CONNECTION .........................................................................................................1-1 W ATER AND MOISTURE.....................................................................................
HDM 5049 PLUS Safety Instructions 1 SAFETY INSTRUCTIONS • • • • Read the safety and operating instructions before operating the monitor. Retain safety and operating instructions for future reference. Adhere to all warnings on the monitor and in the operating instructions manual. Follow all instructions for operation and use. This monitor conforms to the following rules: DHHS21, IEC950/EN60950, UL1950, C-UL950. 1.
HDM 5049 PLUS Features 2 FEATURES The HDM 5049 PLUS is equipped with a super high resolution CRT and a dark and flat face plate, ensuring high contrast ratio and natural looking pictures. Resolution is maintained by excellent spot performance and ultra fine pitch (= 0.26 mm). Its sleek 16:9 aspect ratio and reduced rack space requirements make it the ideal studio picture quality monitor for today’s crammed control and equipment rooms.
HDM 5049 PLUS HDM 5049 PLUS Installation 3 HDM 5049 PLUS INSTALLATION 3.1 Precautions • • • • • Keep your original packaging. It is designed for this monitor and is the ideal protection during transport. Do not lift the monitor alone to avoid injury. Avoid reflections in the picture tube to reduce eye strain. Keep the monitor away from heat sources and provide enough ventilation if it is installed in a rack or console. Keep the monitor away from strong sources of magnetic radiation. 3.
HDM 5049 PLUS Installation HDM 5049 PLUS 3.3.1 Factory-stored HDTV Modes 480L x 704P 60P System: 720L x 1280P 60P 1035L x 1920P 60I SMPTE293M SMPTE296M (483L x 720P) Mode Name: Horizontal Timings: Horizontal Scan Frequency: 1080L x 1920P 60I SMPTE240M- SMPTE274M 260M Units kHz 31,5 45 33,75 33,75 Total Line Time: µs 31,75 22,22 29,63 29,63 Active Line Time: µs 26,64 17,24 25,86 25,86 Horizontal Blanking: µs 5,1 4,98 3,77 3,77 Horizontal Sync Width: µs 2.33(*) 0.54(*) 0.
HDM 5049 PLUS HDM 5049 PLUS Installation 3.3.
HDM 5049 PLUS Operation And Adjustment 4 OPERATION AND ADJUSTMENT 4.1 Using The Keyboard Power On / Off: Press this button to start-up the monitor if it is in standby mode (red led is on). The green led turns on if the monitor has started up. A blinking red led indicates a problem. Degauss (demagnetization). Contrast: Use to reveal / remove the Contrast setting. Adjust with keys simultaneously to return to the calibrated value. Brightness: Use to reveal / remove the Brightness setting.
Operation And Adjustment HDM 5049 PLUS 4.2 Main Menu Press to enter the main menu. Select a submenu with Press or and press to enter. to exit from the main menu. The menu disappears automatically after 20 seconds of keyboard inactivity. 4.3 Status Menu The Status Menu shows the current display mode with its corresponding syncs, the current settings and the detected actual sync frequencies. You cannot make changes in this menu. To make changes, refer to the Settings Menu.
HDM 5049 PLUS Operation And Adjustment Select an item with or . If the item has a red background, press to change it. If the item has a to magenta background, press change it. Changes become active immediately. These settings (except Modename) are valid for all modes. Press to leave the Settings menu. 4.4.1 Modename With or , scroll through the available characters and move the cursor with at the end of the line, the cursor returns to the first character. Press pressing the Mode name. .
Operation And Adjustment HDM 5049 PLUS 4.4.4 Degauss rate The monitor can periodically degauss itself. Press or between off (non-active) and 12 hours. Leave the menu with to change the degauss rate . 4.4.5 Color temp. Press or to change the color temperature from 5000 to 9900 K in steps of 100 K. This setting is also used during automatic color temperature alignment. Leave the menu with . 4.4.6 White level Press or to change the light output from 60 to 120 cd/m² (nit) in steps of 1 cd/m².
HDM 5049 PLUS Operation And Adjustment 4.5 Adjustments Menu Before entering the Adjustments menu, you will be prompted for a four-figure password. The default password is 0000. To enter a password, select a figure from 0 to 9 with or and after you have entered the last figure will press to move the cursor to the next figure. Pressing open the Adjustments menu. If you have entered a wrong password, following message appears: Wait 10 seconds or press , the password entrance menu reappears.
Operation And Adjustment HDM 5049 PLUS Automatic Remember that the monitor will be aligned according to the Color temp. and White level settings you have made in the Settings menu. If you align the monitor to 6000 K and 80 nit, you can set it to 6500 K and 90 nit in the Settings menu, but then, the color temperature and light output will be approximate. To obtain 6500 K and 90 nit, make sure you make the correct settings before starting automatic alignment.
HDM 5049 PLUS Press Operation And Adjustment to return to the Color menu, correct the problem and restart alignment. After alignment is finished, the HDM 5049 PLUS displays following message: Press to return to the Color menu. If alignment failed, the HDM 5049 PLUS displays following message: Press to return to the Color menu. The old alignment values are restored. An alignment can fail due to following reasons: • • • The Thoma has not been adjusted for offset (see procedure above).
Operation And Adjustment HDM 5049 PLUS 4.5.2 Geometry Select a geometry setting with or and press , or press first to turn Scrollbar on or off. Scrollbar on: Scrollbar off: Adjust with or then press . to leave the Geometry menu.
HDM 5049 PLUS Operation And Adjustment 4.5.3 Uniformity Select a setting with or and press , or press first to turn Scrollbar on or off. Scrollbar on: Scrollbar off: Adjust with or then press . Press to leave the Uniformity menu. If changes have been made, you will be asked to save or to discard these changes: Press to select yes or no, then press .
Operation And Adjustment HDM 5049 PLUS 4.6 Information Menu In the Information Menu, you can find the serial number, the part number, the software number and version and the time the monitor has been running since it left the factory. Press to leave the menu. The menu disappears automatically after 20 seconds of keyboard inactivity.
HDM 5049 PLUS Technical Specifications 5 TECHNICAL SPECIFICATIONS HDM 5049 PLUS FEATURES VISUAL PERFORMANCE • • • • • • • Picture tube • Dot-In-Line, diagonal: 19” (17” visible) • Dot pitch: 0.26 mm • Transparency: 46% • Phosphor type: P22, rare-earth (red), sulfide (blue and green) • Max. convergence error: Zone A: 0.3 mm, Zone B: 0.4 mm.
