User Guide

Location and Functions of Control
5975646A BARCOGRAPHICS 8100LC 220496
5-5
Location and Functions of Control
5975646A BARCOGRAPHICS 8100LC 220496
5-5
Terminology
Back light key
: when activated, all keys will be lighted up
and visible in the dark.
ADJ. : ADJUST key, to enter the adjustment mode or for
quick exit in the adjustment mode.
Address key (recessed key), to enter the address of the
projector (between 0 and 9). Press the sunk address key
with a pencil, followed by pressing one digit button be-
tween 0 and 9.
STBY : stand by button - to start projection when the
power switch is switched on.
- to switch off the projector
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
The image disappears but full power is retained for imme-
diate restarting.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT : when adjusting one of the image, e.g. controls
during a meeting, the displayed bar scale can be removed
by pressing 'TEXT' key first. To re-display the bar scale on
the screen, press 'TEXT' key again. 'TEXT' key only active
in operational mode.
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control stick key (on RCU) or '+' and '-' keys (cursor
keys): to make menu selections when in the adjustment
mode.
The control stick can move forward, backward, to the right
or to the left.
Comparision between control stick movement and the use
of the cursor keys on the local keypad :
RCU = local keypad
control stick forward = '+' key up
control stick backward = '-' key down
control stick to the right = '+' key right
control stick to the left = '-' key left
Use the
'+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
1
2
3
4
5
6
7
8
9
12
11
13
10
14
Terminology
Back light key
: when activated, all keys will be lighted up
and visible in the dark.
ADJ. : ADJUST key, to enter the adjustment mode or for
quick exit in the adjustment mode.
Address key (recessed key), to enter the address of the
projector (between 0 and 9). Press the sunk address key
with a pencil, followed by pressing one digit button be-
tween 0 and 9.
STBY
: stand by button - to start projection when the
power switch is switched on.
- to switch off the projector
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
The image disappears but full power is retained for imme-
diate restarting.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT : when adjusting one of the image, e.g. controls
during a meeting, the displayed bar scale can be removed
by pressing 'TEXT' key first. To re-display the bar scale on
the screen, press 'TEXT' key again. 'TEXT' key only active
in operational mode.
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control stick key (on RCU) or '+' and '-' keys (cursor
keys): to make menu selections when in the adjustment
mode.
The control stick can move forward, backward, to the right
or to the left.
Comparision between control stick movement and the use
of the cursor keys on the local keypad :
RCU = local keypad
control stick forward = '+' key up
control stick backward = '-' key down
control stick to the right = '+' key right
control stick to the left = '-' key left
Use the
'+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
1
2
3
4
5
6
7
8
9
12
11
13
10
14