User Guide

ManualsBrandsBarco ManualsOtherGRAPHICS 8100LC

OWNER'S MANUAL

GRAPHICS

8100LC

R9001109

Art. No. :R5975646A

Date: 130696

BARCO PROJECTION SYSTEMS

OWNER'S MANUAL

GRAPHICS

8100LC

R9001109

Art. No. :R5975646ADate: 130696

BARCO PROJECTION SYSTEMS

Rev. : 01

Summary of content (149 pages)

PAGE 1
BARCO PROJECTION SYSTEMS GRAPHICS 8100LC R9001109 OWNER'S MANUAL Date: 130696 Art. No. :R5975646A Rev. : 01 BARCO PROJECTION SYSTEMS GRAPHICS 8100LC R9001109 OWNER'S MANUAL Date: 130696 Rev. : 01 Art. No.
PAGE 2
Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, June 1996 All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, June 1996 All rights reserved. Trademarks are the rights of their respective owners.
PAGE 3
Table of Contents WARNINGS & SAFETY INSTRUCTIONS ........................................................................................................................................ 1-1 AVERTISSEMENTS & PRESCRIPTIONS DE SECURITE ............................................................................................................... 1-1 UNPACKING & DIMENSIONS ............................................................................................................................................
PAGE 4
Table of Contents RGB analog input module. .................................................................................................................................................... 7-6 Component input module. ..................................................................................................................................................... 7-9 RGB3S/RG3sB input module. ................................................................................................................
PAGE 5
Table of Contents Gamma ............................................................................................................................................................................. 11-15 Geometry .......................................................................................................................................................................... 11-16 Shift ....................................................................................................................
PAGE 6
Table of Contents Hardwired RCU. .................................................................................................................................................................. 14-2 RCVDS 800 / RCVDS 05 .................................................................................................................................................... 14-3 VS05 ...................................................................................................................................
PAGE 7
Safety Instructions WARNINGS AVERTISSEMENTS Safety instructions Prescriptions de securite On safety Securite On installation Installation On servicing Entretien et reparation On cleaning Nettoyage On repacking Re-emballage On illumination Eclairage 1-1 5975646A BARCOGRAPHICS 8100LC 220496 Safety Instructions WARNINGS AVERTISSEMENTS Safety instructions Prescriptions de securite On safety Securite On installation Installation On servicing Entretien et reparation On cleaning Nettoyage On repacking Re-emba
PAGE 8
Prescription de sécurtié Remarque sur la Sécurité DONNEES POUR LE PROPRIETAIRE Les projecteurs sont fabriqués conformément aux exigences des normes de sécurité internationales IEC950, UL 1950 et CSA C22.2 No. 950. Ces normes de sécurité sont imposées aux équipements de la technologie informatique incluant les équipements électriques. Le numéro de pièce et le numéro de série sont situés à l’arrière du projecteur. Copier ces numéros dans les espaces prévus ci-dessous.
PAGE 9
Safety Instructions Notice on safety OWNER’S RECORD Projectors are built in accordance with the requirements of the international safety standards IEC950, UL 1950 and CSA C22.2 No. 950, which are the safety standards of information technology equipment including electrical business equipment. The part number and serial number are located at the rear of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your BARCO dealer regarding this product.
PAGE 10
Prescription de sécurtié ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION : AFIN DE REDUIRE LE RISQUE DE CHOCS ELECTRIQUES, NE PAS ENLEVER LE COUVERCLE (OU LE DOS) IL N'Y A PAS DE PIECES REPARABLES PAR L'UTILISATEUR A L'INTERIEUR LE SERVICE NE PEUT ETRE EFFECTUE QUE PAR DU PERSONNEL QUALIFIÉ L’éclair avec une tête de flèche dans un triangle indique à l’utilisateur que les pièces à l’intérieur de l’appareil présentent un risque de chocs électriques.
PAGE 11
Safety Instructions The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product are risk of electrical shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and/or servicing instructions are included in the technical documentation for this equipment.
PAGE 12
Prescription de sécurtié Instructions pour l’utilisateur : type avec terre. Ceci est une mesure de sécurité. Si le connecteur ne s’adapte pas dans la prise, contacter votre électricien pour Si cet équipement cause des interférences de radio ou de télévision, remplacer la prise non valable. Ne pas compromettre le but du l’utilisateur peut essayer de corriger les interférences en appliquant connecteur de terre.
PAGE 13
Safety Instructions Instructions to the user : plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type if this equipment does cause interference to radio or television plug. reception, the user may try to correct the interference by one or more WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED (EARTHED) via the supplied 3 conductor AC power of the following measures : cable.
PAGE 14
Prescription de sécurtié * Pour débrancher le cordon, le tirer par le connecteur, jamais par le * Ne pas utiliser le projecteur à proximité d’eau. cordon lui-même. * N’utiliser que le cordon d’alimentation fourni avec votre projecteur.
PAGE 15
Safety Instructions * To disconnect the cord, pull it out by the plug. Never pull the cord * Use only the power cord supplied with your projector. While itself. appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the projector. * If an extension cord is used with this product, make sure that the For a replacement power cord, contact your dealer.
PAGE 16
Prescription de sécurtié * Laisser suffisamment d’espace autour du projecteur et ne pas Pièces de rechange - Lorsqu’on a besoin des pièces de rechange, obstruer la circulation de l’air. Ne pas mettre des feuilles libres ou veiller à ce que le technicien de service utilise des pièces d’origine d’autres objets plus près de 11 cm du projecteur. BARCO ou des pièces équivalentes autorisées qui ont les mêmes caractéristiques que la pièce d’origine BARCO.
PAGE 17
Safety Instructions * Do not block the projector cooling fans or free air movement under Replacement parts - When replacement parts are required, be sure and around the projector. Loose papers or other objects may not be the service technician has used original BARCO replacement parts nearer to the projector than 4" on any side. or authorized replacement parts which have the same characteristics as the BARCO original part.
PAGE 18
Prescription de sécurtié Pour garantir les meilleures performance et définition, les objectifs de projection sont spécialement traités avec un revêtement anti-reflets. En conséquence : éviter de toucher les objectifs. Pour enlever la poussière de l’objectif, utiliser un chiffon sec et doux. Ne pas utiliser de chiffon humide, de solution détergente ou de diluant. Respecter la méthode de nettoyage des objectifs indiquée dans l’annexe D au manuel d'utilisateur.
PAGE 19
Safety Instructions To ensure the highest optical performance and resolution, the On illumination projection lenses are specially treated with an anti-reflective coating, therefore : avoid touching the lens. To remove dust on the lens, use In order to obtain the best quality for the projected image, it is essential a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
PAGE 20
Prescription de sécurtié 1-14 5975646A BARCOGRAPHICS 8100LC 220496 Presciptions de sécurité 1-14 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 21
Unpacking & Dimensions UNPACKING DIMENSIONS BATTERY INSTALLATION ON THE RCU 5975646A BARCOGRAPHICS 8100LC 220496 2-1 Unpacking & Dimensions UNPACKING DIMENSIONS BATTERY INSTALLATION ON THE RCU 5975646A BARCOGRAPHICS 8100LC 220496 2-1
PAGE 22
Unpacking & Dimensions Unpacking To open the banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table. For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts. When using the projector as a table mounted configuration, always mount the 3 supporting feet by turning in into the provided holes (see drawing on next page).
PAGE 23
Unpacking & Dimensions Projector dimensions (units : mm) L Some examples of lenses : Name lens (*) L min mm(inch) L max mm(inch) HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(3.9:1) HD(5:1) HD(7:1) HD(1.5-3:1) 1072 1043 1017 1022 1082 1252 1325 1087 1070 1072 1162 1202 1372 1355 (42.20) (41.06) (40.04) (40.24) (42.60) (49.29) (52.17) (42.79) (42.12) (42.20) (45.75) (47.32) (54.02) (53.
PAGE 24
Unpacking & Dimensions Battery installation in the RCU. A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
PAGE 25
Installation Guidelines INSTALLATION GUIDELINES Environment What about ambient light? Which screen type? What image size? How big should the image be? Where to install the projector? How to install the projector? 3-1 5975646A BARCOGRAPHICS 8100LC 220496 Installation Guidelines INSTALLATION GUIDELINES Environment What about ambient light? Which screen type? What image size? How big should the image be? Where to install the projector? How to install the projector? 5975646A BARCOGRAPHICS 8100LC 220496 3
PAGE 26
Installation Guidelines Installation guidelines Careful consideration of things as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. * Environment Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity.
PAGE 27
Installation Guidelines * Which screen type? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain.
PAGE 28
Installation Guidelines * Where to install the projector? Inputs and computer video format input compatibility : Definitions of the Abbreviation on drawings Some examples : B = Distance between ceiling and top of the screen or between floor and bottom of the screen. A = Correction value, distance between bottom side of projector and middle of the lens. Value to be subtracted from B to obtain the correct installation position.
PAGE 29
Installation Guidelines Ceiling mounting of the BARCOGRAPHICS 8100LC Table mounting of the BARCOGRAPHICS 8100LC Ceiling CD B PD A Optical axis projection lens CD = B - A SH Projector Screen Screen Projector SH CD = B - A Optical axis projection lens B SIDE VIEW PD A CD Floor SIDE VIEW SW Screen Screen SW BOTTOM VIEW TOP VIEW Ceiling SW SH SH SW BACK VIEW Floor BACK VIEW 3-5 5975646A BARCOGRAPHICS 8100LC 220496 Installation Guidelines Ceiling mounting of the BARCOGRAPHICS 810
PAGE 30
Installation Guidelines * How to install a projection lens? The BARCOGRAPHICS 8100LC is supplied without any lens. The following lenses are available as an option : HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(4.0:1) HD(5:1) HD(7:1) HD(1.5-3:1) HD(3.0-5.3:1) WHD(3.5:1) BARCO ceiling support. Order number : R9827341 Always use the BARCO ceiling support to attach your BARCOGRAPHICS 8100LC to the ceiling. The installation instruction for this support is enclosed in the packet of the set.
PAGE 31
Installation Set Up INSTALLATION SET UP Projector configuration 4-1 5975646A BARCOGRAPHICS 8100LC 220496 Installation Set Up INSTALLATION SET UP Projector configuration 5975646A BARCOGRAPHICS 8100LC 220496 4-1
PAGE 32
Installation Set Up The BARCOGRAPHICS 8100LC can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling. Rear/Ceiling Front/Ceiling Rear/Table Front/Table 4-2 5975646A BARCOGRAPHICS 8100LC 220496 Installation Set Up The BARCOGRAPHICS 8100LC can be installed to project images in four different configurations : front/table, front/ceiling, rear/table and rear/ceiling.
PAGE 33
Installation Set Up To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER. Highlight Installation by pushing the control stick forward or backward and press ENTER to select. The installation menu will be displayed. ENTER displays the Installation menu. EXIT returns to operational mode. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with or then to return.
PAGE 34
Installation Set Up 4-4 5975646A BARCOGRAPHICS 8100LC 220496 Installation Set Up 4-4 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 35
Location and Functions of Control LOCATION AND FUNCTION OF CONTROLS Front panel terminology Local keypad Remote control 5-1 5975646A BARCOGRAPHICS 8100LC 220496 Location and Functions of Control LOCATION AND FUNCTION OF CONTROLS Front panel terminology Local keypad Remote control 5975646A BARCOGRAPHICS 8100LC 220496 5-1
PAGE 36
Location and Functions of Control Front panel terminology PROJECTOR MODE : DIAGNOSTICS CODE IR-RECEIVER GREEN - OPERATION COMMUNICATION PORT RS232 OUT RS 232 IN (800-PERIPHERALS) RED - STANDBY Th is de vice co mplies w ith Part 1 5 o f the F CC rules.
PAGE 37
Location and Functions of Control Control Panel Terminology a. Local keypad Getting access The keypad is located behind a door, screened with the name of the projector. To open the door, push once on the indicated side of the door and turn it to the front side of the projector. 9 0 7 8 5 6 3 4 1 2 b. Remote control This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely.
PAGE 38
Location and Functions of Control 14 Remote Control (RCU) Local keypad 13 1 14 4 2 3 4 13 9 7 0 12 11 8 STBY PAUSE TEXT 6 ENTER 6 TEXT 3 4 SHARPN TINT BRIGHTN 1 2 PHASE COLOR CONTRAST PAUSE 9 ENTER 11 10 FREEZ + - PHASE 9 0 - 7 8 - 5 6 - 3 4 1 2 8 + SHARPNESS 5 5 12 9 5 EXIT STANDBY EXIT ADJ 7 + TINT + COLOR + - BRIGHTNESS - + CONTRAST 7 8 6 32a 5-4 5975646A BARCOGRAPHICS 8100LC 220496 Location and Functions of Control 14 Remote Co
PAGE 39
Location and Functions of Control Terminology the screen, press 'TEXT' key again. 'TEXT' key only active in operational mode. 1 Back light key : when activated, all keys will be lighted up and visible in the dark. 10 2 ADJ. : ADJUST key, to enter the adjustment mode or for quick exit in the adjustment mode. 11 ENTER : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode. Address key (recessed key), to enter the address of the projector (between 0 and 9).
PAGE 40
Location and Functions of Control 5-6 5975646A BARCOGRAPHICS 8100LC 220496 Location and Functions of Control 5-6 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 41
Power Connection POWER CONNECTION 6-1 5975646A BARCOGRAPHICS 8100LC 030696 Power Connection POWER CONNECTION 5975646A BARCOGRAPHICS 8100LC 030696 6-1
PAGE 42
Power Connection Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. The power input is auto-ranging from 100 to 240 VAC. This projector may be connected to an IT-power system. PROJECTOR MODE : GREEN - OPERATION Fuses COMMUNICATION PORT RS 232 IN Warning For continued protection against fire hazard : - replace with the same type of fuse.
PAGE 43
Power Connection When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red. To start image projection : a. press the 'Stand by' button on the local keypad or on the remote control. The projector mode indication lamp will be green.
PAGE 44
Power Connection When the total run time of the lamp is 970 hours or more, the following message will be displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. When the total run time of the lamp is 1000 hours or more, the following message, with the exact run time is displayed on the screen. Lamp run time 980 h Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage the projector.
PAGE 45
Connections INPUT MODULE CONNECTIONS Module insertion into the BARCOGRAPHICS 8100LC. Video/S-Video input module RGB analog input module Component input module RGB3S/RG3sB input module Peripheral equipment connection Connecting a computer Connecting a RCVDS800 or RCVDS05 Connecting a VS05 Connecting an IR Remote Receiver 800 7-1 5975646A BARCOGRAPHICS 8100LC 220496 Connections INPUT MODULE CONNECTIONS Module insertion into the BARCOGRAPHICS 8100LC.
PAGE 46
Connections Input connections. The BARCOGRAPHICS 8100LC has modular input facilities. The input slots can be filled up with the following modules : DIAGNOSTICS CODE Video, S-video (NTSC) input order no. R9827900 RGBS/RGsB analog input order no. : R9827910 RGB3S/RG3sB input order no. : R9827920 Component Video input order no. : R9827930 IR-ACKNOWLEDGED IR-RECEIVER RS232 OUT 0 I 1 00 - 23 0 V 9 - 4A 60 - 50 H z IR-RECEIVED The sequence of insertion has no importance.
PAGE 47
Connections Video/S-video input module On On To the Video input : Composite video signals from a VCR, OFF air signal decoder, etc... 1 x BNC 1.0Vpp ± 3 dB VIDEO/S-VIDEO INPUT To the S-Video input : Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals. 1 x 4 pins plug (mini DIN) pin configuration : 1 ground luminance 2 ground chrominance 3 luminance 1.
PAGE 48
Connections Push the Control stick key forward or backward to highlight Installation and press ENTER to display the Installation menu. EXIT returns to operational mode. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Use the control stick to select Input Slots by pushing it forward or backward and press ENTER. The internal system will scan the inputs and displays the result in the Input Slots menu. Source 01 Select with or then to return.
PAGE 49
Connections Straps on module level. Floating or non-floating input. Video input : J11 : strap "yes" : non floating strap "no" : floating Floating or non floating input J13 J12 J11 S-Video input : J12 : strap "yes" : non floating strap "no" : floating J13 : strap "yes" : non floating strap "no" : floating Factory preset : strap on, input non floating. 7-5 5975646A BARCOGRAPHICS 8100LC 220496 Connections Straps on module level. Floating or non-floating input.
PAGE 50
Connections RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB RGB analog input terminals with separate Horizontal and Vertical Blue : 0.7 Vpp ± 3 dB sync inputs(RGB-HV), with Composite sync input(RGB-S) or with Green : 0.7 Vpp ± 3 dB Sync signals on green(RGsB). 1 Vpp ± 3 dB if sync on green Vert. sync : 1 Vpp to 4 Vpp ± 3 dB Always use an interface when a computer and local monitor have to Hor. sync / Composite sync : be connected to the projector.
PAGE 51
Connections RGB input selection : Floating or non floating input J4 J5 J6 Key in the corresponding slot number on the RCU or the local keypad. Straps on module level : J3 J7 Floating or non-floating input.
PAGE 52
Connections Push the control stick key forward or backward to select Installation and press ENTER. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Use the control stick to select Input Slots by pushing forward or backward and press ENTER. The internal system will scan the inputs and displays the result in the Input Slots menu. Source 01 Select with or then to return.
PAGE 53
Connections Component input module. Connect your component signals (Y-luma, R-Y and B-Y), e.g. a professional VCR to the Component input module. Component video : 4 x BNC R-Y : 0.7 Vpp ± 3 dB B-Y : 0.7 Vpp ± 3 dB Y : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if Tri-level sync on green Composite sync : 1 Vpp to 4 Vpp ± 3 dB On COMPONENT VIDEO INPUT All input signals are always 75 ohm terminated, even the module is "not selected".
PAGE 54
Connections Component input selection : Key in the corresponding slot number on the RCU or the local keypad. Indication on the input slot menu : Component Component Component sync Component Y Video-SS = Component video with separate sync Video-SOY = Component video with sync on Y Video-3LSS = Component video with 3 level separate Floating or non floating input J3 J4 J5 J6 Video-3LSOY = Component video with 3 level sync on Straps on module level : Floating or non-floating input.
PAGE 55
Connections Connect your RGB signals with Tri-level sync, e.g. a professional VCR to the RGB 3 level sync input module. RGB3S/RG3sB analog : 5 x BNC Red :0.7 Vpp ± 3 dB Blue : 0.7 Vpp ± 3 dB Green : 0.7 Vpp ± 3 dB 1 Vpp ± 3 dB if Tri-level sync on green Vert. Tri-level sync : 1 Vpp to 4 Vpp ± 3 dB Hor. Tri-level sync / Composite Tri-level sync: 1 Vpp to 4 Vpp ± 3 dB R G B H/C V On 98 27920 RGB3S/RG3sB input module. RGB 3-LEVEL SYNC INPUT Vert. 3 level sync Hor.
PAGE 56
Connections Straps on module level : Floating or non-floating input. Red : J3 : strap "yes" : non floating Green : J4 : strap "yes" : non floating Blue : J5 : strap "yes" : non floating H/C : J6 : strap "yes" : non floating V: J7 : strap "yes" : non floating strap "no" : floating strap "no" : floating strap "no" : floating strap "no" : floating strap "no" : floating Factory preset : strap "yes", non floating input Floating or non floating input J4 J5 J6 J3 J7 Sync selection.
PAGE 57
Connections Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector. DIAGNOSTICS CODE IR-RECEIVER R R This device co mplies w ith Part 15 of the FCC rul es.
PAGE 58
Connections Connecting a RCVDS 800 or RCVDS 05 to the BARCOGRAPHICS 8100LC. Connecting an IR Remote Receiver 800 to the BARCOGRAPHICS 8100LC. - Up to 10 inputs with one RCVDS800 or 20 inputs with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module. - Serial communication with the projector. - Remote control buttons on the RCVDS to control the BARCOGRAPHICS 8100LC (source selection and analog settings).
PAGE 59
Controlling CONTROLLING How to use the RCU. Projector address How to display a projector address. How to program an address into the RCU. Picture controls with direct access. 8-1 5975646A BARCOGRAPHICS 8100LC 130696 Controlling CONTROLLING How to use the RCU. Projector address How to display a projector address. How to program an address into the RCU. Picture controls with direct access.
PAGE 60
Controlling The BARCOGRAPHICS 8100LC can be controlled with a. the RCU b. the hardwired RCU (cable is not included) c. the local keypad. b) RCU used in a hardwired configuration. Controlling the projector with the RCU and the hardwired RCU is equal. DIAGNOSTICS CODE IR-RECEIVER T hi s devi c e comp l i es w i t h P a rt 15 of t he F CC r ul es.
PAGE 61
Controlling c) Point the front of the RCU directly at one of the IR sensors of the projector. IR sensor a. Software set up of the projector address. IR sensor Ceiling Projector address See 'Change projector address' in chapter 'Service mode'. IR-RECEIVED 0 I DIAGNOSTICS IR-RECEIVER IR-ACKNOWLEDGED CODE Table Front of projector Rear of projector Every projector requires an individual address between 0 and 255 which can be set in the Service mode.
PAGE 62
Controlling How to display a projector address? Press the ADDRESS key (sunk key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds. To continue using the RCU, it is necessary to enter the same address with the digit buttons (address between 0 and 9). For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU's address to match the projector's address.
PAGE 63
Controlling Contrast Control Tint Control A correct 'contrast' setting is important for good image reproduction. Adjust the contrast to the level you prefer, according to room lighting conditions. Use the + button for a higher contrast. Use the - button for lower contrast. Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system. Use the + button Use the - button. Sharpness Control. Color Saturation Use the + button for a sharper picture.
PAGE 64
Controlling 8-6 5975646A BARCOGRAPHICS 8100LC 130696 Controlling 8-6 5975646A BARCOGRAPHICS 8100LC 130696
PAGE 65
Start Up of the Adjustment Mode START UP OF THE ADJUSTMENT MODE 9-1 5975646A BARCOGRAPHICS 8100LC 220496 Start Up of the Adjustment Mode START UP OF THE ADJUSTMENT MODE 5975646A BARCOGRAPHICS 8100LC 220496 9-1
PAGE 66
Start Up of the Adjustment Mode Adjustment Mode All source set ups, picture tunings and geometry are made while in the 'Adjustment mode' . Press the ADJUST or ENTER key to enter the 'Adjustment mode'. You are now in the 'Adjustment mode'. The control stick (RCU) or '+ or '-' keys (local keypad) are used to make menu selections and also for adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure.
PAGE 67
Start Up of the Adjustment Mode Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, see 'Change password' in chapter 'Service mode'. Your password contains 4 digits. Enter the digits with the numeric keys. Example : 2 3 1 9 The first digit position is highlighted. Enter with the numeric keys.
PAGE 68
Start Up of the Adjustment Mode 9-4 5975646A BARCOGRAPHICS 8100LC 220496 Start Up of the Adjustment Mode 9-4 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 69
Guided Adjustment Mode GUIDED ADJUSTMENT MODE 10-1 5975646A BARCOGRAPHICS 8100LC 220496 Guided Adjustment Mode GUIDED ADJUSTMENT MODE 5975646A BARCOGRAPHICS 8100LC 220496 10-1
PAGE 70
Guided Adjustment Mode The Guided Adjustment Mode is not active. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with or then to return. 10-2 5975646A BARCOGRAPHICS 8100LC 220496 Guided Adjustment Mode The Guided Adjustment Mode is not active. ADJUSTMENT MODE Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with or then to return.
PAGE 71
Random Access Adjustment Mode RANDOM ACCESS ADJUSTMENT MODE File Service Picture Tuning Geometry 11-1 5975646A BARCOGRAPHICS 8100LC 130696 Random Access Adjustment Mode RANDOM ACCESS ADJUSTMENT MODE File Service Picture Tuning Geometry 5975646A BARCOGRAPHICS 8100LC 130696 11-1
PAGE 72
Random Access Adjustment Mode Starting up the Random Access Adjustment Mode ADJUSTMENT MODE Push the control stick forward or backward to highlight 'Random Access' and then press ENTER. Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with or then to return. RANDOM ACCESS ADJUSTMENT MODE FILE SERVICE PICTURE TUNING GEOMETRY Select with or then to return.
PAGE 73
Random Access Adjustment Mode File service Before using a new source, a correct file has to be installed. The projector's memory contains a list of files corresponding to the most used sources. When the new source corresponds with one of these files, the file can be loaded and saved for future use. When there is a little difference, the file can also be loaded and than edited until the source specs are reached. File annotation : xxxxxxxx.
PAGE 74
Random Access Adjustment Mode Load file Push the control stick forward or backward to select LOAD and press ENTER to display the Load menu. The Load menu displays the corresponding files depending on the installed filter. This filter can be "Fit" or "All". To change the filter, push the control stick to the right to select "filter list" (filter list will be hightlighted) and press ENTER to toggle the annotation between brackets. "All" : all files that can be loaded will be displayed.
PAGE 75
Random Access Adjustment Mode Edit file The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data. To start up the EDIT menu, push the control stick forward or backward to select EDIT in the FILE menu and press ENTER. Select the file which must be edited (mostly the active file) and press ENTER. The Edit file adaptation menu will be displayed.
PAGE 76
Random Access Adjustment Mode forward or backward to scroll to desired digit. When finished press of the projected image. This value is normally given in the specificaENTER to confirm. tion of the source. If not, adjust until full image height is displayed (no c. counting up or down by pushing the joy stick key to the right or to missing lines) the left.
PAGE 77
Random Access Adjustment Mode Options Source number : The source number of a non-active source can be changed to any other source number. This makes it possible to create a file for future source numbers. EDIT FILE OPTIONS Source number 1 Clamp position [leading] Clamp delay 0 Clamp width 10 Field polarity [pos] Field select [both] Vertical refresh [sync] Vert.
PAGE 78
Random Access Adjustment Mode Vertical refresh [sync/async] : The way of updating the image information on the LCD panels. For moving images, the vertical refresh has to be done on a synchronous way, for still images, asynchronous vertical refresh is possible. Vertical sync polarity : [leading] or [trailing] The vertical refresh can be synchronised with the leading sync edge or trailing sync edge. Default on [leading].
PAGE 79
Random Access Adjustment Mode Rename To change the name of a selected file. Use the control stick to select RENAME and press ENTER. The Rename selection menu will be displayed. Use the control stick to select a file name and press ENTER to select. The Rename menu will be displayed with the selected file name already filled in in the 'From file name :' area and in the 'To file name :' area. FILE SERVICE LOAD EDIT RENAME COPY DELETE OPTIONS Select with or then to return.
PAGE 80
Random Access Adjustment Mode Copy FILE SERVICE To copy a selected file into a new file. Use the control stick to select COPY and press ENTER. The Copy selection menu will be displayed. Use the control stick to select a file name and press ENTER to select. The Copy menu will be displayed with the selected file name already filled in in the 'From file name :' area and in the 'To file name :' area. LOAD EDIT RENAME COPY DELETE OPTIONS Select with or then to return.
PAGE 81
Random Access Adjustment Mode Delete FILE SERVICE To delete a selected file out of the list of files. Use the control stick to select DELETE and press ENTER. The delete selection menu will be displayed. Push the control stick forward or backward to select a file and press ENTER. If [All] is selected, your password has to be entered before all files will be deleted. LOAD EDIT RENAME COPY DELETE OPTIONS Select with or then to return.
PAGE 82
Random Access Adjustment Mode File Options FILE SERVICE Use the control stick to select OPTIONS and press ENTER. The option selection menu will be displayed. Press ENTER to toggle between [name] and [index] [name] : The files in the file list will be sorted on the file name. [index] : The files in the file list will be sorted on the file extension. LOAD EDIT RENAME COPY DELETE OPTIONS Select with or then to return.
PAGE 83
Random Access Adjustment Mode Sync slow/fast PICTURE TUNING Highlight sync by pushing the control stick forward or backward and press ENTER to toggle between SLOW and FAST. SYNC [SLOW] STILL VIDEO [ON] COLOR BALANCE GAMMA Note : Sync is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment. Select with or then to return.
PAGE 84
Random Access Adjustment Mode Color Balance PICTURE TUNING Highlight Color Balance by pushing the control stick forward or backward and press ENTER to select the color balance selection menu. SYNC : SLOW STILL VIDEO : ON COLOR BALANCE GAMMA The next choices are possible : Fixed color balance : - 3200 K (reddish) - 6500 K (white) - 9300 K (bluish) Select with or then to return.
PAGE 85
Random Access Adjustment Mode Gamma PICTURE TUNING With the gamma correction adjustment, it is possible to bring the details in dark image parts more to the front (lower image values) or to reduce the importance of these details (higher gamma values). To change the gamma value, highlight Gamma by pushing the control stick forward or backward and press ENTER. SYNC [SLOW] STILL VIDEO [ON] COLOR BALANCE GAMMA Select with or then to return. GAMMA 2.
PAGE 86
Random Access Adjustment Mode Geometry Highlight Geometry by pushing the control stick forward or backward and press ENTER to select the geometry selection menu. The following adjustment are possible : - horizontal and vertical image shift. - horizontal and vertical image size - side keystone (only necessary if the projector is mounted under a non standard projection angle).
PAGE 87
Random Access Adjustment Mode Size GEOMETRY Highlight Size by pushing the control stick forward or backward and press ENTER to select. SHIFT SIZE SIDE KEYSTONE BLANKING OPTIONS Select with or then to return. The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size, for table mount configuration : the upper side of the image is fixed and only the lower side can be moved to its exact position.
PAGE 88
Random Access Adjustment Mode Side keystone GEOMETRY Highlight Side Keystone by pushing the control stick forward or backward and press ENTER to select. The side keystone adjustment is used to align the image if the projector is mounted as a non standard projection angle. SHIFT SIZE SIDE KEYSTONE BLANKING OPTIONS Select with or then to return. Push the control stick to the right or to the left to adjust the keystone of the image.
PAGE 89
Random Access Adjustment Mode Blanking GEOMETRY Highlight Blanking by pushing the control stick forward or backward and press ENTER to select. SHIFT SIZE SIDE KEYSTONE BLANKING OPTIONS Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking. Select with or then to return.
PAGE 90
Random Access Adjustment Mode Adjustment of the blanking on the of the image BLANKING TOP BOTTOM LEFT RIGHT Adjustment of the blanking on the bottom of the image Correct by pushing the control stick forward or backward Select with or then to return.
PAGE 91
Random Access Adjustment Mode Options GEOMETRY Highlight Options by pushing the control stick forward or backward and press ENTER. The Geometry Options menu will be displayed. The next question will be asked by the projector : 'Use the same side keystone correction for all files ? [YES] or [NO]. [YES] : the same keystone correction will be used for all installed files. [NO] : the keystone has to be adjusted file per file. Push the ENTER key to toggle between [YES] or [NO].
PAGE 92
Random Access Adjustment Mode 11-22 5975646A BARCOGRAPHICS 8100LC 130696 Random Access Adjustment Mode 11-22 5975646A BARCOGRAPHICS 8100LC 130696
PAGE 93
Installation INSTALLATION Convergence Configuration Internal Patterns 12-1 5975646A BARCOGRAPHICS 8100LC 220496 Installation INSTALLATION Convergence Configuration Internal Patterns 5975646A BARCOGRAPHICS 8100LC 220496 12-1
PAGE 94
Installation Starting up the Installation Mode ADJUSTMENT MODE Push the control stick forward or backward to highlight Installation and then press ENTER. ENTER continues to the Installation mode selection menu. EXIT returns to operational mode. Select a path from below : GUIDED RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with or then to return.
PAGE 95
Installation Input Slots Highlight Input Slots by pushing the control stick forward or backward and press ENTER. The internal system will scan the input slots and displays the result in the Input Slots menu.
PAGE 96
Installation Convergence INSTALLATION Highlight "Convergence" by pushing the control stick forward or backward and press ENTER to display the convergence selection menu. Every LCD panel has 6 adjustment screws. By turning these screws you change the relative position of the panels and converge the image. Always start with the adjustment of the green panel. When the green image is correctly focused, it will later on be used as the reference image to converge the red and blue image.
PAGE 97
Installation To adjust the convergence, there are test patterns provided in the convergence menu. Use the control stick to hightlight Convergence and press ENTER to display the Convergence menu. Start with the Green test pattern and continue with the Red on green and finish with the Blue on green. Use the control stick to select Green and press ENTER to display the green pattern. CONVERGENCE GREEN BLUE ON GREEN RED ON GREEN HATCH Select with or then to return.
PAGE 98
Installation The three alignments influence each other, therefore repeat if necessary the above three steps (b,c and d). When the green pattern is correctly focused, press EXIT to return to the Convergence menu. Red on green convergence. Use the control stick to hightlight Red on green and press ENTER to display the Red on green test pattern. CONVERGENCE GREEN BLUE ON GREEN RED ON GREEN HATCH Select with or then to return. The longest lines are the red lines.
PAGE 99
Installation If both lines are correctly converged, continue with screw 4. Adjust screw 4 until line 4 is correctly converged. It is possible that line 2 and 3 have to be reconverged. If so, repeat procedure for screw 2 and 3 (step b and c) If line 2, 3 and 4 are converged, continue with line 1 (screw 1). When line 1 is converged, check again the convergence of lines 2, 3 and 4. If necessary repeat the above procedure for the corresponding lines. Check if lines 5 and 6 are correctly converged.
PAGE 100
Installation Blue on green convergence. Use the control stick to highlight Blue on green and press ENTER to display the Blue on green test pattern. Repeat the same procedure as for Red on green lines but read blue when red is indicated. CONVERGENCE GREEN BLUE ON GREEN RED ON GREEN HATCH Select with or then to return. To check the result of the convergence adjustments, highlight Hatch and press ENTER. A hatch pattern will be displayed on the screen. ENTER : displays a hatch pattern.
PAGE 101
Installation Configuration INSTALLATION Highlight "Configuration" by pushing the control stick forward or backward and press ENTER to select. INPUT SLOTS CONVERGENCE CONFIGURATION INTERNAL PATTERNS For more information, see Projector configuration in chapter Installation Set Up. Select with or then to return. Internal Patterns The projector is equipped with different internal patterns which can be used for measurment purposes.
PAGE 102
Installation 12-10 5975646A BARCOGRAPHICS 8100LC 220496 Installation 12-10 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 103
Service Mode SERVICE MODE Identification Change Password Change Language Change Projector Address Change Baudrate PC Reset Lamp Run Time Lamp Run Time History Panel Adjustments Preset Color Balance 60 Hz Tracking I²C Diagnosis 13-1 5975646A BARCOGRAPHICS 8100LC 130696 Service Mode SERVICE MODE Identification Change Password Change Language Change Projector Address Change Baudrate PC Reset Lamp Run Time Lamp Run Time History Panel Adjustments Preset Color Balance 60 Hz Tracking I²C Diagnosis 5975646A BAR
PAGE 104
Service Mode Starting up the Service Mode ADJUSTMENT MODE Push the control stick forward or backward to highlight Service and then press ENTER. Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now available if you stay in the adjustment mode. The service menu is built-up in two parts which are connected together with the 'more' item.
PAGE 105
Service Mode SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY MORE... Select with or then to return. BARCO GRAPHICS 8100LC CHANGE PASSWORD CHANGE LANGUAGE Enter new password 0000 ENGLISH Select with or then to return. Select with or then to return. CHANGE PROJ.
PAGE 106
Service Mode SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY MORE... Select with or then to return. PANEL ADJUSTMENT RED COARSE PRESET INPUT BALANCE WHITE BALANCE FIELD FLICKER BLACK LEVEL TOP BLACK LEVEL BOTTOM GAIN TOP GAIN BOTTOM Select with to return Change color+pattern with or Select with or then to return.
PAGE 107
Service Mode Identification To display the Identification sreen, push the control stick forward or backward to highlight Identification and press ENTER to display the Identification screen. The Identification screen gives an overview of : - type of projector - projector address - software version - installation configuration - baud rate - text ON - projector serial number - projector run time SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ.
PAGE 108
Service Mode - Baud rate : transfer speed for communication with a IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult Set up of the baud rate for communication with a computer in chapter Connections. 13-6 - Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.
PAGE 109
Service Mode Change Password This item is password protected when the password strap is installed. Loosen the locking screws. How to enable or disable the password function ? The password function is enabled when the password strap on the controller module is installed. B B RS232 OUT V V R DI AGNOSTICS CODE I R-RECEIVER This device complies with Part 15 ofthe FCC rules.
PAGE 110
Service Mode When the strap is on leg 2-3 or no strap is mounted, the password function is enabled, when the strap is on leg 1-2, the password function is disabled. Password enabled strap on leg 2-3 Password disabled strap on leg 1-2 13-8 5975646A BARCOGRAPHICS 8100LC 130696 Service Mode When the strap is on leg 2-3 or no strap is mounted, the password function is enabled, when the strap is on leg 1-2, the password function is disabled.
PAGE 111
Service Mode How to change the password ? Highlight Change password by pushing the control stick forward or backward and press ENTER to display the Change Password menu. ENTER displays the Change Password menu EXIT returns to the adjustment selection menu. The old password is displayed and can be changed by entering the digit with the numeric keys of the RCU or local keypath. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ.
PAGE 112
Service Mode Change Projector Address Every projector requires an individual address between 0 and 255. This address can be software installed. To change that address, push the control stick forward or backward to highlight Change Proj. Address and press ENTER. The Change Projector Address menu will be displayed and the actual address will be filled in. The first digit is highlighted.
PAGE 113
Service Mode The following baud rates are available : - 9600 - 4800 - 2400 - 1200 - 600 - 300 - 150 - 75 The actual baud rate will be highlighted. To change the baud rate, push the control stick forward or backward and press ENTER to accept the new baud rate setting. CHANGE BAUDRATE PC 9600 4800 2400 1200 600 300 150 75 Select with or to accept to return. Reset Lamp Runtime Reset lamp run time is only allowed when a new lamp is installed.
PAGE 114
Service Mode Lamp Run Time History To get an overview of the different lamp run times, highlight Lamp Run Time History by pushing the control stick forward or backward and press ENTER. A listing with the lamp serial number and the corresponding run time will be displayed. The actual installed lamp will be marked. Press EXIT to return to the service mode selection menu. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ.
PAGE 115
Service Mode Panel Adjustments SERVICE Changing these settings may seriously affect the performance of the projector. All panel adjustments are factory adjusted. If not really necessary, do not touch one of these adjustments. They are useful when a new panel is installed. PANEL ADJUSTMENTS PRESET INPUT BALANCE 60Hz TRACKING I2C DIAGNOSIS Highlight Panel Adjustments by pushing the control stick forward or backward and press ENTER Select with or then to return. MORE...
PAGE 116
Service Mode Preset Input Balance Highlight White Balance by pushing the control stick forward or backward and press ENTER to select. With the white balance adjustment, the gain of the red and blue channels can be adjusted in comparison with the green channel. (To adjust the gain of the complete video signal, use the contrast adjustment) Use the control stick by pushing forward or backward to change Red or by pushing to the right or to the left to change Blue.
PAGE 117
Service Mode 60 Hz Tracking 60 Hz tracking is used to adjust the 60 Hz by sychronious signals SERVICE Highlight 60 Hz Tracking by pushing the control stick forward or backward and press ENTER. When 60 Hz Tracking is selected in the Service Mode selection menu, the following warning will be displayed : 60 Hz Tracking is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the 60 Hz Tracking. PANEL ADJUSTMENTS PRESET INPUT BALANCE 60Hz TRACKING I2C DIAGNOSIS MORE...
PAGE 118
Service Mode I2C diagnosis. Give an overview of the correct working of the I²C controlled IC's. Highlight I2C diagnosis by pushing the control stick forward or backward and press ENTER to display the overview. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY PANEL ADJUSTMENTS I2C DIAGNOSIS Select with or then I2C DIAGNOSIS to return.
PAGE 119
Optional Equipment OPTIONAL EQUIPMENT IR remote receiver Hardwired RCU RCVDS800/RCVDS05 VS05 MAGIK interface Adapter and communication cables Ceiling mount kit CM100 Transport handle Frame for dual or triple projection Multifunctional flightcase Mechanical shutter Adjustable lensholder 14-1 5975646A BARCOGRAPHICS 8100LC 220496 Optional Equipment OPTIONAL EQUIPMENT IR remote receiver Hardwired RCU RCVDS800/RCVDS05 VS05 MAGIK interface Adapter and communication cables Ceiling mount kit CM100 Transport ha
PAGE 120
Optional Equipment IR Receiver 800 Communication cable IR Remote Receiver 800 This infra red receiver unit makes it possible to control the BARCOGRAPHICS 8100 from another room. There is a communication line with cable between the IR receiver and the projector or the RCVDS. The control information from the RCU can now be sent to this IR receiver. The IR receiver 800 displays the selected source on a 7-segment display.
PAGE 121
Optional Equipment RCVDS 800 / RCVDS 05 An optional RCVDS 800 source selector makes it possible to connect up to ten sources to the projector, an optional RCVDS 05 source selector makes it possible to connect up to 20 sources to the projector. When RCVDS's are linked via the expansion module, even 90 inputs can be connected to the projector. The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear.
PAGE 122
Optional Equipment MAGIK Interface Multifuctional Analog Graphics Interface Kit. BARCO's MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display. The MAGIK interface buffers and amplifies any RGB analog signal with TTL or analog sync without signal loss or image degradation.
PAGE 123
Optional Equipment Available length :5 m (16ft), order number R982770; 15 m(50ft), order number R9827640; and 30 m (100ft), order number R9827570 b. Din Mini8-D9 adapter cable. - To connect a Macintosh computer to the BARCOGRAPHICS 8100. (only if the optional RS232 port is installed.) Available length : 1 m, order number R9827640. c. D25-D9 adapter cable - To connect a workstation to the BARCOGRAPHICS 8100.(only if the optional RS232 port is installed.) Available length : 1 m, order number R9827630 d.
PAGE 124
Optional Equipment Projector Transport Handle 0.72 m 1.15 m Order number : R9829170 Projector Frame for Dual or Triple Configurations The frame is designed for use in table as well as ceiling mount configurations. The projector can be easily locked in the solid black frame via three bolts. The modular construction of the frame enables dual or triple configurations, in combination with the adjustable lensholder for convergence of the two or three images and provides a very high light output.
PAGE 125
Optional Equipment Multifunctional flight case BARCO's multifunctional flight case is a special designed flight case for temporary installations of a BARCOGRAPHICS 8100 projector. Due to the advanced mechanical design of the flight case and the built-in mirror, it is possible to install the projector in a horizontal as well as in a vertical position - in ceiling mount or table configuration - without removing the projector out of the flight case.
PAGE 126
Optional Equipment Mechanical Shutter BARCO's mechanical shutter can be used there where the display has to be totally black when the projector is set in pauze. This can be very useful when the projector is used together with a slide-projector. Features: - Is installed inside the projector. - The shutter is controlled through the 'pause' button on the RCU. - The shutter is powered through the power supply of the projector. - The fading time is adjustable through RS232 communication.
PAGE 127
Appendix A : Standard Source Set Up Files Standard source set up files.
PAGE 128
Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX Hz kHz MHz PTOT PACT LTOT LACT VGA75ISO 640 X 480 75,000 39,375 31,500 800 640 525 480 MAC_2 640 X 480 66,667 35,000 30,240 864 640 525 480 MAC_LC 640 X 480 66,619 34,975 31,338 896 640 525 480 MUSE 960 X 518I 30,000 33,750 37,125 1100 960 563 518 HDMAC 1008 X 570I 25,020 31,250 39,125 1252 1008 625 570 SVGA_56V 800 X 600 56,250 35,156 36,000 1024 800 625 600 SVGA_60V 800 X 600 60,317 37,879 40
PAGE 129
Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX Hz kHz MHz PTOT PACT LTOT LACT INTER_GR 1184 X 886 67,170 61,796 92,941 1504 1184 920 886 EWS_50 280 X 1024 50,000 52,350 87,948 1680 1280 1047 1024 EWS_60 280 X 1024 60,000 63,900 107,352 1680 1280 1064 1024 EWS_60V 280 X 1024 60,282 63,657 110,000 1728 1280 1056 1024 EWS_72 280 X 1024 72,000 76,968 130,076 1690 1280 1069 1024 EWS_75 1280 X 1024 75,025 79,976 135,000 1688 1280 1066 1024 SG_60_1
PAGE 130
Appendix A : Standard Source Set Up Files NAME RESOLUTION FVERT FHOR FPIX Hz kHz MHz PTOT PACT LTOT LACT PAM800 1120 X 375I 89,872 36,443 50,000 1372 1120 406 375 FMTO_2 640 X 400 55,370 24,370 21,060 864 640 440 400 FMR 640 X 400I 84,700 36,440 28,570 784 640 431 400 SUNXGA60 1024 X 768 59,984 48,287 64,125 1328 1024 805 768 SUNXGA70 1024 X 768 70,041 56,596 74,250 1312 1024 808 768 SUNXGA77 1024 X 768 77,069 62,040 84,375 1360 1024 805 768 SUNEWS67 1280 X 1024 67,189 7
PAGE 131
Appendix B : Battery Replacement in the RCU Battery replacement in the RCU. Remove the battery cover on he backside of the remote control by pushing the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time. (fig. 1) Remove the battery from the compartment and disconnect the contact plate. (fig. 2) Connect a new 9 V battery (E-block type, e.g. type 6F22S or equivalent) to the contact plate. Insert the battery back into the compartment. Put the cover back.
PAGE 132
Appendix B : Battery Replacement in the RCU B-2 5975646A BARCOGRAPHICS 8100LC 220496 Appendix B : Battery Replacement in the RCU B-2 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 133
Appendix C : Focusing the Lens Focusing the lens Loosen the fastener ring of the lens by turning counter clockwise. Focus the image by turning the lens barrel to the left or the right. Attention : Do not turn out the lens too far, otherwise it will fall out of the lens holder. When the image is focused, secure the correct position of the lens with the fastener ring by turning this ring clockwise.
PAGE 134
Appendix C : Focusing the Lens C-2 5975646A BARCOGRAPHICS 8100LC 220496 Appendix C : Focusing the Lens C-2 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 135
Appendix D : Lens Cleaning Procedure Lens Cleaning Procedure Cleaning procedure for HD(1.5-3:1) lens and HD(3-5.3:1) lens. Cleaning procedure for the other HD lens To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
PAGE 136
Appendix D : Lens Cleaning Procedure the lens. Wipe at a speed that is equal to the evaporation rate. This is very important to prevent streaking and spotting. Start your wiping at one side of the lens and, with successive wipes, move to the other side. Turn the pad over for each wipe, then inside out. Do not make more than one wipe per clean area of pad. Be careful of the painted edge, since acetone will soften it. D-2 5975646A BARCOGRAPHICS 8100LC 220496 Appendix D : Lens Cleaning Procedure the lens.
PAGE 137
Appendix E : Source Number 90 - 99 Source numbers 90 - 99 These source numbers do not correspond to physical inputs. They can only be used when the projector is equipped with a RCVDS 800 or RCVDS 05 or VS05. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 0 - 9 and 90 - 99 is shown in the diagram below.
PAGE 138
Appendix E : Source Number 90 - 99 E-2 5975646A BARCOGRAPHICS 8100LC 220496 Appendix E : Source Number 90 - 99 E-2 5975646A BARCOGRAPHICS 8100LC 220496
PAGE 139
Appendix F : Lenses Lenses This APPENDIX gives an overview of the tables and formulas for the available lenses for the BARCOGRAPHICS 8100LC. An overview of all tables, diagrams and formulas can also be found in the manual "Installation diagrams for BARCO projectors", order number : R5975924. The next lenses are available : Name length lens mm (inch) diam. lens mm (inch) weight kg (lbs) order number HD(1.2:1) 253 (9.96) 189 (7.44) 8.7 (19.2) R9829200 HD(2.2:1) 235 (9.25) 137 (5.39) 7.5 (16.
PAGE 140
Appendix F : Lenses Lens table metric standard (units : meter) SW HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(4.0:1) HD(5.1:1) PD 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 1.408 1.533 1.658 1.783 1.908 2.034 2.160 2.285 2.411 2.537 2.663 2.789 2.915 3.041 3.167 3.293 3.419 3.545 3.672 3.798 3.924 4.050 4.176 4.303 4.429 4.555 4.681 4.808 4.934 5.060 5.187 5.313 PD PD 2.246 2.449 2.652 2.856 3.060 3.264 3.469 3.673 3.878 4.
PAGE 141
Appendix F : Lenses SW HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(4.0:1) HD(5.1:1) PD 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0 9.482 9.608 9.735 9.861 9.988 10.114 10.240 10.367 10.493 10.619 10.746 10.872 10.998 11.125 11.251 11.378 11.504 11.630 11.757 11.883 12.010 12.136 12.262 12.389 12.515 12.641 12.768 PD PD 15.383 15.588 15.794 16.000 16.205 16.411 16.616 16.822 17.028 17.233 17.439 17.645 17.850 18.056 18.261 18.467 18.673 18.878 19.
PAGE 142
Appendix F : Lenses SW 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 HD(7:1) HD(1.5-3:1) HD(3-5.3:1) PD PD PD 29.082 29.773 30.463 31.154 31.844 32.535 33.225 33.916 34.607 35.297 35.988 36.679 37.370 38.060 38.751 39.442 40.133 40.824 41.514 42.205 42.896 43.587 44.278 44.969 45.659 46.350 47.041 47.732 48.423 49.114 49.805 min. max. min. 6.083 6.232 6.381 6.530 6.679 6.828 6.977 7.126 7.275 7.424 7.573 7.722 7.871 8.
PAGE 143
Appendix F : Lenses Lens table inch standard (units : inch) SW HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(4.0:1) HD(5.1:1) PD 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 56.22 62.46 68.72 74.99 81.27 87.55 93.84 100.13 106.43 112.73 119.03 125.33 131.64 137.95 144.25 150.56 156.87 163.18 169.50 175.81 182.12 188.43 194.75 201.06 207.38 213.69 220.01 226.32 232.64 238.95 245.27 251.58 PD 89.69 99.84 110.03 120.23 130.44 140.67 150.90 161.
PAGE 144
Appendix F : Lenses SW HD(1.2:1) HD(2.2:1) HD(3.3:1) HD(4.0:1) HD(5.1:1) PD 360 365 370 375 380 385 390 395 460.08 466.40 472.72 479.04 485.35 491.67 497.99 504.31 PD 746.80 757.08 767.36 777.64 787.93 798.21 808.49 818.77 PD 1214.19 1230.84 1247.48 1264.13 1280.78 1297.43 1314.07 1330.72 PD 1467.15 1487.24 1507.34 1527.44 1547.53 1567.63 1587.73 1607.83 SW PD 1829.71 1854.71 1879.70 1904.70 1929.70 1954.69 1979.69 2004.68 HD(7:1) HD(1.5-3:1) HD(3-5.3:1) PD PD PD min.
PAGE 145
Appendix F : Lenses SW 195 200 205 210 215 220 225 230 235 240 245 250 255 260 265 270 275 280 285 290 295 300 305 310 315 320 325 330 335 340 345 HD(7:1) HD(1.5-3:1) HD(3-5.3:1) PD PD PD 1404.47 1439.00 1473.54 1508.08 1542.62 1577.16 1611.70 1646.24 1680.78 1715.32 1749.86 1784.41 1818.95 1853.49 1888.04 1922.58 1957.13 1991.67 2026.22 2060.76 2095.31 2129.86 2164.40 2198.95 2233.50 2268.05 2302.59 2337.14 2371.69 2406.24 2440.79 min. max. 295.39 302.84 310.29 317.74 325.19 332.64 340.09 347.
PAGE 146
Appendix F : Lenses Lens formulas to calculate the projector distance. HD(1.2:1) Metric PD=1.264 x SW + 0.126 + (0.018/SW) Inch PD= 1.264 x SW + 4.961 + (27.90/SW) HD(2.2:1) Metric PD=2.0566 x SW + 0.16 + (0.029/SW) Inch PD=2.0566 x SW + 6.299 + (44.95/SW) HD(3.3:1) Metric PD=3.33 x SW + 0.386 + (0.046/SW) Inch PD=3.33 x SW + 15.19 + (71.30/SW) HD(4.0:1) Metric PD=4.02 x SW + 0.50 + (0.06/SW) Inch PD=4.02 x SW + 19.69 + (93/SW) HD(5:1) Metric PD=5 x SW + 0.747 + (0.070/SW) Inch PD=5 x SW + 29.
PAGE 147
PAGE 148
BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium
PAGE 149
Insert card RCU RCU RCU INPUT SOURCES PROJECTOR 1 INPUT SOURCES PROJECTOR 1 P2 2 3 4 5 6 7 INPUT SOURCES RCVDS " P 3 4 5 6 7 INPUT SOURCES RCVDS 1 2 1 2 3 5 6 3 5 6 7 8 9 7 8 9 10 10 5975646A BARCOGRAPHICS 8100LC 220496 Insert card RCU " 5975646A BARCOGRAPHICS 8100LC 220496 RCU RCU INPUT SOURCES PROJECTOR 1 2 3 4 5 6 7 INPUT SOURCES PROJECTOR 1 P2 3 4 5 6 7 INPUT SOURCES RCVDS INPUT SOURCES RCVDS 1 2 1 2 3 5 6 3 5 6 7 8 9 7 8 9 10 10 P