Nio display systems Getting Started Guide Supported displays: E-2621, E-3620, MDNG-5121, MDNG-2121, MDNC 3120, MDNC-3121, MDNG-6121, MDNC-2121
(This page intentionally left blank.
Copyright notice This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco © 2011 Barco N.V. All rights reserved. Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found.
(This page intentionally left blank.
Table of Contents Table of Contents Preface..................................................................................... 7 FCC compliance information ............................................................ 8 FCC statement for the display .................................................. 8 FCC statement for the graphic board ....................................... 9 CE mark notice ............................................................................... 11 Environmental information .....
Table of Contents Cleaning instructions...................................................................... 52 Front filter ............................................................................... 52 Cabinet .................................................................................... 53 Software installation ............................................................. 55 Driver and Software Installation ...................................................
Preface Preface 7
FCC compliance information FCC compliance information FCC statement for the display FCC Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FCC compliance information Canadian notice This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada. Korean notice FCC statement for the graphic board FCC Compliance Information (display controller) Class B: This Barco Graphics Controller complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
FCC compliance information • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to ensure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by Barco could void the user’s authority to operate this equipment.
CE mark notice CE mark notice Declaration of Conformity in accordance with Article 10 (1) of the CE directive This product has been designed and manufactured in accordance with the essential requirements of the Directives 89/336/EEC and MDD 93/42/EEC (class II b product), and for this product the procedures of Annex II have been applied to mark the product with the CE label.
Environmental information Environmental information Disposal Information This product consists of devices that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws. (Within this system, the backlight lamps in the monitor display contain mercury.) This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment.
Environmental information Information for China ROHS compliance Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling pollution by electronic information products Toxic or hazardous Substances and Elements Part Name Pb Hg Cd Cr6+ PBB PBDE Metal parts O O O O O O Plastic parts O O O O O O PCB or PCBA O O O O O O LCD panel X X O O O O Power supply/adapter X O O O O O Power cable X O O O O O
Environmental information LCD Monitor 零部件名稱 有毒有害物質或元素 铅 汞 镉 （Pb） （Hg） （Cd） 金属机构件 O O O 塑料机构件 O O O O O O 电路板组件 * X X O 液晶面板 X O O 电源模块 / 适配器 X O O 电源线 O O O 外部信号连接线 六价铬 （Cr6+） O O O O O O O 多溴联苯 多溴二苯醚 （PBB） （PBDE） O O O O O O O O O O O O O O *： 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路 、连接器等 ○：表示该有毒有害物质在该部件所有均质材料中的含量均在 《电子信息产品中有 毒有害物质的限量要求标准》规定的限量要求以下 ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 《电子信息产品 中有毒有害物质的限量要求标准》规定的限量要求； 但是上表中打 “×” 的部件，其含量超出是因为目前业界还没有成熟的可替代的技术 14
Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use.
Safety Instructions • The medical approved DC power supply must be powered by the AC mains voltage. Power connection - MDNC-3121 and MDNC-2121 • Power requirements: The display must be powered using the delivered medical approved 24 VDC SELV power supply. • The medical approved DC power supply must be powered by the AC mains voltage. Transient over-voltage If the equipment is not used for a long time, disconnect it from the AC inlet to avoid damage by transient over-voltage.
Safety Instructions heed the necessary space between the set and the sides of the cupboard. Installation Place the display on a flat, solid and stable surface that can support the weight of at least 3 displays. If you use an unstable cart or stand, the display may fall, causing serious injury to a child or adult, and serious damage to the equipment. More warnings in the Installation chapter. This apparatus conforms to: CE0120 (MDD 93/42/EEC class IIb product), IEC 60601-1, UL 60601-1, CAN/CSA C22.2 No. 601.
Recommendations for using your display system Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of your display (in the display’s Settings menu) will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time. By default, DPMS is enabled on your display, but it also needs to be activated on your workstation.
Recommendations for using your display system diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white paper available at www.barcomedical.com. 4. Enhance user comfort Every Barco multi-head display system is color matched with the highest specification in the market. Barco recommends keeping color-matched displays together.
Explanation of symbols Explanation of symbols Symbols on the display and / or power supply On the display or power supply, you may find the following symbols (nonrestrictive list): Indicates compliance to the essential requirements of the Directive 93/42/EEC Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the display is approved according to the UL regulations or or Indicates the display is approved according to the c-UL regulations Indicates the display is approved acc
Explanation of symbols Indicates the display serial no.
Explanation of symbols (This page intentionally left blank.
Introduction Introduction 23
Installation overview Installation overview 1 If applicable, install the graphic board in the computer. 2 Remove the foot rear cover. Pull out the red clip from the tilt & swivel foot. 3 If you wish to rotate the panel, first tilt the panel slightly in order not to damage the tilt & swivel mechanism. 4 Connect the cables: Video (DVI/ DisplayPort) and power. Route the cables into the provided clips and guides in the tilt & swivel foot.
Installation overview 5 Install software and user manuals. 6 Start up and use MediCal QAWeb Agent. 7 Important Enable DPMS & screensaver for optimal display performance throughout the product lifetime.
Display parts, controls and connectors Display parts, controls and connectors Front view 1 BAR CO 3 2 Figure 1: Front side 1. Power LED The LED is off when the display is disconnected from the power. The LED is also off when the LED function is disabled in the onscreen display (OSD). The LED is green when the display is on (when enabled in the on-screen menus). The LED is orange when the display is in Stand-by power-saving mode. 2. USB downstream port. See also item “7.
Display parts, controls and connectors It allows to put the display in stand-by, navigate through the onscreen display (OSD) menus and change values in the OSD. Rear view of E-2621, E-3620, MDNG-5121 1 2 4 5 6 7 8 9 3 Figure 2: Rear side 1. Connector compartment cover To get access to the connectors, remove the cover by pulling down the 2 clips at the top of the cover. 2. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer. 3.
Display parts, controls and connectors When the display is connected to the PC USB bus, you can connect USB devices, such as keyboard, mouse, digital camera, to this connector. 8. DC power input Connect the external power supply, delivered with the display, to this connector. 9. Tilt & swivel foot clip The display is shipped with this clip in the foot to protect the tilt & swivel mechanism during transport. After unpacking, you should remove this clip.
Display parts, controls and connectors 2. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer. 3. Tilt & swivel foot 4. DC power input Connect the external power supply, delivered with the display, to this connector. 5. +5 Vdc, 0.25 A power output for accessories. 6. Slot for security cable (e.g., Kensington lock) 7. DVI (digital) video input 8.
Display parts, controls and connectors Rear view of MDNC-2121 1 2 4 5 6 7 8 9 10 3 Figure 4: Rear side 1. Connector compartment cover To get access to the connectors, remove the cover by pulling down the 2 clips at the top of the cover. 2. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer. 3. Tilt & swivel foot 4. Slot for security cable (e.g., Kensington lock) 5. DisplayPort video input 6. DVI (digital) video input 7.
Display parts, controls and connectors When the display is connected to the PC USB bus, you can connect USB devices, such as keyboard, mouse, digital camera, to this connector. 9. DC power input Connect the external power supply, delivered with the display, to this connector. 10. Tilt & swivel foot clip The display is shipped with this clip in the foot to protect the tilt & swivel mechanism during transport. After unpacking, you should remove this clip.
Display parts, controls and connectors (This page intentionally left blank.
Display controller installation Display controller installation 33
Display Controller Installation Display Controller Installation Which display controller? Your Barco medical display is compatible with a large range of Barco and non-Barco display controller boards. Depending on the customer’s order details, the display can be delivered with or without a display controller. The brochure “Barco medical display systems” on the website www.barco.
Display Controller Installation Types of display controllers for Barco Display Systems The following models of Barco display controllers are available for your display system.
Display Controller Installation Installation Procedure The following instructions will take you step by step through the installation of the display controller(s) for your BARCO NIO Display System. CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller. Electrostatic charges can damage the display controller. 1. If you are not going to use your old graphics card, uninstall the drivers and software for it if you have not already done so. 2.
Display Controller Installation 7. Align the display controller(s) for your BARCO NIO Display System with the slot(s) and press it(them) in firmly until the card(s) is(are) fully seated. Note: The next step applies only to the MXRT 7300. 8. Connect the power cable to the 6-pin power connection on the graphics card. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan).
Display Controller Installation Connecting your Barco displays For a detailed description of the display installation and signal connection, please refer to the “Display installation” section of this manual. MXRT 1150 & MXRT 2150 IO-Panel for the Barco MXRT 1150 and Barco MXRT 2150 X S-Video Connection This option is not supported by Barco. Y DMS-59 connector provides DVI-I / Head 1 & Head 2 output connections through included Y adaptor cable.
Display Controller Installation MXRT 7300 IO-Panel for the Barco MXRT 7300 X DisplayPort Connections Y DVI-I Connection Note: Disconnecting the DisplayPort cable may lock the display. Rebooting system may be required if lock occurs. Note: Only two of the three connectors can be used at a time. Driving three displays is not supported with the MXRT 7300.
Display Controller Installation DualLink Dongle - for color 3mp or higher (ex: MDCC-6130). Must be ordered separately, part number B560602. Firmware v1.07 or higher required. 11. Reconnect any cables you have disconnected and plug in the computer’s power cord. 12. Turn on the display(s) and then your computer. Turning on your system WARNING - Turn on your display(s) before you turn on your computer. Failure to do so could damage your display(s).
Display Controller Installation 13. Install the drivers, QAWeb software and documentation for your BARCO NIO Display System by following the instructions in the Driver and Software Installation section of this manual.
Display Controller Installation (This page intentionally left blank.
Display installation Display installation 43
Installation precautions Installation precautions Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation around the display. • Do not use the display in direct sunlight. • Do not scratch or apply pressure to the screen. This may cause permanent damage.
Installation precautions To remove the clip: 1. Position the display with its rear side facing you. 2. Pull the red clip out of the fixation holes in the foot. 3. Keep the clip in case the display needs to be shipped later. Adjust the panel orientation You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables.
Installation precautions Figure 7: Tilt the panel before rotating 3. To change from portrait to landscape, turn the panel counterclockwise. BAR CO Figure 8: To rotate the panel from portrait to landscape 4. To change from landscape to portrait, turn clockwise. Note: If, after installing the display or the system, you change the panel orientation while an image is on the screen, the result depends on the graphic board and the resolution of the image.
Installation precautions rotation). If necessary, change the image resolution in the display control panel and restart the system after changing the orientation.
Connecting the signal cables Connecting the signal cables To connect the signal cables to the display: To get access to the connectors, remove the connector compartment cover by pulling down the 2 clips at the top of the cover.
Cable routing Cable routing Routing the signal cables • Bind the cables in the connector compartment together with the cable tie inside the connector compartment. • Put the connector compartment cover back on the display. Pay attention that the signal cables are positioned under the bulge in the cover. • Push the cables into the clips on the rear of the tilt & swivel foot.
Vesa-mount installation 2. Push the upper side of the cover onto the foot, so that the hooks inside the cover are positioned right under the bulges at the rear of the foot. 3. Slide the cover upward while moving the lower side of the cover towards the foot. 4. Press the cover to the foot so that it makes a clicking sound. Vesa-mount installation The panel, standard attached to the tilt & swivel foot, is compatible with the VESA 100 mm standard.
Vesa-mount installation B A Figure 13: Display with tilt & swivel foot cover removed 4. Unscrew the 2 screws fixing the round plastic cover (B). 5. Lift up the round plastic cover. 6. Remove the four screws fixing the foot while supporting the foot. 7. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm.
Cleaning instructions Cleaning instructions Precautions • Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the front filter. • Do not apply pressure on the front filter or LCD panel. • Do not apply or spray liquid directly to the front filter, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the cleaning cloth.
Cleaning instructions • Detergents with ammonia • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet Proceed as follows: • Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment. • Repeat with water only. • Wipe dry with a dry cloth.
Cleaning instructions (This page intentionally left blank.
Software installation Software installation 55
Driver and Software Installation Driver and Software Installation This chapter will guide you through the installation of the drivers, software and documentation associated with your BARCO NIO Display System or BARCO NIO Display(s). Driver and software installation prerequisites Note: To install or remove the drivers, software, or documentation you must be logged on as a user with administrator privileges.
Driver and Software Installation • After you have reinstalled or upgraded your operating system. • When you upgrade to a newer version of the MXRT driver. Note: You do not need to manually uninstall an existing driver before updating to the current version. The Barco Product Installation Wizard will detect any prior installations and start the uninstallation process automatically if necessary.
Driver and Software Installation The master Install program will make two passes through the driver installation process (i.e. License Agreement, Verify Installation Options, etc.). 6. During installation, there may be a fair amount of display flashing, and the install wizard window may appear on different displays. This is an expected behavior. 7. When the installation of all components has completed, the automatic reboot window will be displayed. Allow the system to reboot.
Driver and Software Installation Reinstalling drivers You can install new drivers or reinstall existing drivers at any time by using the Barco Set-up wizard on your BARCO NIO Display System Installation CD-ROM, see Installing the BARCO MXRT drivers and software, on page 56 of this manual. Uninstalling the drivers and software To uninstall the Barco drivers, software or documentation for your Nio display Systems, please use the Windows Add/Remove Program.
Driver and Software Installation Silent Installation of Drivers and Software Once A Barco graphics driver has been pre-loaded into the driver store of a Windows 7 OS, subsequent installation of the driver would be intervention-free. To pre-load the driver software into the driver store, open a command shell and navigate to the appropriate driver directory and run the PnPUtil program with the -a "add" parameter. For example: cd d:\Barco\drivers\VS32\MXRT pnputil -a *.
Where to get more information Where to get more information Where to find more information The following documentation is included with your system: Document Location Information Quick install sheet System box Brief overview of the complete system set-up Online user guide Installed on the PC Detailed description of the graphic board control panels and display controls and functions Getting started guide (PDF) System CD-ROM This booklet in PDF format Online user guide (PDF) System CD-ROM Same
Where to get more information • In Windows control panel, select Internet Options • Select the Advanced tab • In the Security section, check the option Allow active content to run in files on My Computer 62
Troubleshooting Troubleshooting 63
General tips General tips • If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not.
Configuring Windows Configuring Windows Setting the resolution of your BARCO NIO Display Note: In order to set the resolution of your BARCO NIO Display you must be logged in using an account with administrator privileges. Accessing the Windows Display Control Panel 1. Right click on the desktop, and select Screen resolution. 2. From the Windows Display Control Panel, hi-lite the Barco display whose mode you wish to set, and select Advanced settings. 3.
Configuring Windows 1. Click on Display. 2. Click on Change Display Settings. 3. In the Multiple Displays drop down list, these options are available (this only appears if there is more than 1 display connected to system): • Duplicate these displays • Extend these displays • Show desktop only on 1 • Show desktop only on 2 4. Select the desired setting. Configuring Software Rotation 1. In the Windows Control Panel, click on Appearance and Personalization. 2. Click on Display. 3.
Technical specifications Technical specifications MDNG-2121: Item Specification Picture panel 21.3-inch diagonal viewable screen IPS grayscale liquid crystal display Resolution Native: 1600 x 1200 Display area (H x V) 432.0 x 324.0 (mm) Viewing angle (@ 10/1 contrast) Vertical: 88º Horizontal: 88º Pixel Pitch 0.27 mm (H) x 0.
Technical specifications Item 68 Specification Power source Input for 12 VDC power supply unit: 90 ~ 264 VAC Input for display: 12 VDC. (The supplied 12VDC power supply must be used) Power consumption 57 watts (nominal, at 90 VAC, calibrated, no USB load) Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+25° Swivel angle 45° left/right Net weight 12.
Technical specifications E-3620 (MA): Item Specification Picture panel 20.8-inch TFT AM-LCD IPS dual domain Resolution Native: 2048 x 1536 Display area (H x V) 423.9 x 318 (mm) Viewing angle (@ 10/1 contrast) Vertical: 170º Horizontal: 170º Pixel Pitch 0.207 mm (H) x 0.
Technical specifications Item 70 Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation
Technical specifications MDNG-5121: Item Specification Product acronym MDNG-5121 Screen technology TFT AM LCD Dual Domain IPS Active screen size (diagonal) 541 mm (21.3") Active screen size (H x V) 422 x 338 mm (16.5" x 13.3" Aspect ratio (H:V) 5:4 Resolution 5MP (2560 x 2048) Pixel pitch 0.
Technical specifications Item 72 Specification Contrast ratio (ULT off) 800:1 Response time (Tr + Tf) 25 ms Scanning frequency (H; V) 30-124 kHz; 45-85 Hz Housing color Gray Video input signals DVI-D Dual Link Video inout terminals NA USB ports 1 upstream (endpoint), 2 downstream USB standard 1.
Technical specifications Item Specification Net weight packaged w/ o stand NA Height adjustment range 60 mm Tilt -5° / +30° Swivel -45° / +45° Pivot 90° Mounting standard VESA (100 mm) Screen protection Protective, non-reflective PMMA cover Recommended modalities CT, MR, US, DR, CR, NM, Film Certifications CE, UL60601, CSA C22.2 No 601.
Technical specifications Item 74 Specification Storage humidity 5% - 95% (non-condensing) Operating altitude 2000 m Storage altitude 7500 m
Technical specifications MDNC 3120 (MA): Item Specification Picture panel 20.8” TFT AM LCD, Dual domain IPS, color Resolution Native: 2048 x 1536 Display area (H x V) 423.9 x 318.0 Viewing angle (@ 10/1 contrast) Vertical: 170º Horizontal: 170º Pixel Pitch 0.207 mm (H) x 0.
Technical specifications Item 76 Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation
Technical specifications MDNC-3121: Item Specification Picture panel 21.3” LCD, IPS, color Resolution Native: 2048 x 1536 Display area (H x V) 433.152 x 324.864 Viewing angle (@ 10/1 contrast) Vertical: 88º Horizontal: 88º Pixel Pitch 0.2115 mm (H) x 0.
Technical specifications Item 78 Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 13 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 2000 m operation
Technical specifications E-2621 (MA): Item Specification Picture panel 21.3-inch diagonal viewable screen TFT (thin film transistor) active matrix, grayscale liquid crystal display Resolution Native: 1600 x 1200 Display area (H x V) 432.0 x 324.0 (mm) Viewing angle (@ 10/1 contrast) Vertical: 160º Horizontal: 160º Pixel Pitch 0.27 mm (H) x 0.
Technical specifications Item 80 Specification Power consumption 57 watts (nominal, at 90 VAC, calibrated, no USB load) Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+30° Swivel angle 45° left/right Net weight 14 kg Operating Temperature Operation: 0°C to 40°C Within specs: 15°C to 35°C Storage Temperature -20°C to 60°C Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for stor
Technical specifications MDNG-6121: Item Specification Picture panel 21.3-inch diagonal viewable screen IPS grayscale liquid crystal display Resolution Native: 2800 x 2096 Display area (H x V) 432.6 x 324.5 (mm) Viewing angle (@ 10/1 contrast) Vertical: 85º Horizontal: 85º Pixel Pitch 0.154 mm (H) x 0.
Technical specifications Item 82 Specification Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Tilt angle -5°/+25° Swivel angle 45° left/right Net weight 12.
Technical specifications MDNC-2121: Item Specification Product acronym MDNC-2121 Screen technology TFT AM Color LCD IPS Active screen size (diagonal) 541 mm (21.3") Active screen size (H x V) 432 x 324 mm (17.0 x 12.8") Aspect ratio (H:V) 4:3 Resolution 2MP (1600 x 1200) Pixel pitch 0.
Technical specifications Item 84 Specification Contrast ratio (ULT off) 1050:1 Response time (Tr + Tf) 35 ms Scanning frequency (H; V) 30-150 kHz; 15-80 Hz Housing color Gray Video input signals DVI-D Single Link (1x) / DisplayPort (1x) Video inout terminals NA USB ports 1 upstream (endpoint), 2 downstream USB standard 2.
Technical specifications Item Specification Net weight packaged with stand 19.3 kg Net weight packaged w/ o stand NA Height adjustment range 60 mm Tilt -5° / +30° Swivel -45° / +45° Pivot 90° Mounting standard VESA (100 mm) Screen protection Protective, non-reflective PMMA cover Recommended modalities CT, MR, US, DR, CR, NM, Film Certifications UL60601-1, CB60601-1, CSA C22.2 No 601.
Technical specifications Item Warranty 5 years Operating temperature 0°C to 40°C (15°C to 35°C within specs) Storage temperature -20°C to 60°C Operating humidity 8% - 70% (non-condensing) Storage humidity 5% - 95% (non-condensing) Operating altitude 3600 m Storage altitude 12000 m Regulation causion 86 Specification Medical equipment with respect to electric shock, fire and mechanical hazards only in accordance with UL 606011. and CAN/CSA C22.2 NO. 601.1.
Warranty Statement Warranty Statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program.
Warranty Statement equipment. All parts replaced hereunder and returned to Barco nv, MID (or an authorised service centre) shall become the property of Barco nv, MID (or the authorised service centre). 1.5 The repaired equipment shall be returned to the Customer, by regular freight, at Barco nv, MID’s charge. 1.6 Barco nv, MID will replace a product that fails within 90 days after shipment from Barco with a new one, ensuring color matching in the event of a diagnostic multi head display configuration.
Warranty Statement • A display is used at 8 hours/day; ie. +/-2.920hours/year • The display system is covered with a warranty period of 5 year • The Guaranteed Backlight Lifetime of that model is 17.000hours. • The Factory Calibrated Luminance cannot be achieved anymore after 4 year, thus corresponding to +/-11.680hours • Result: the backlight replacement is performed under warranty Eg2. • A display is used at 24 hours/day; ie. 8.
Warranty Statement 2.10 The evaluation cost in case of a returned product deemed functional is not covered under warranty and will be charged to the Customer, at Barco’s sole discretion, based on a case-by-case evaluation.
Warranty Statement circumstances which are beyond the control of the parties and hinder performance by one party of his obligations. ARTICLE 8: GENERAL 8.
B410582-06 May 2011 Barco nv President Kennedypark 35 8500 Kortrijk Belgium www.barco.
