B4100240 / 11 May 2004 Coronis® 3MP Installation & User Manual
CONTENTS Introduction ....................................................................................................... 7 Introduction ......................................................................................................... 9 Contents of the package ................................................................................ 9 Other relevant documents .............................................................................. 9 Important installation considerations ............
Display installation ......................................................................................... 21 Overview ........................................................................................................... 24 Introduction ................................................................................................... 24 Package contents ......................................................................................... 25 Controls and connectors ............................
Software Installation .......................................................................................... 47 Installing the BarcoMed 3MP2FH, 2MP2FH or 1MP2FH Windows NT 4.0 Software ....................................................................................................... 47 Using the BarcoMed Product Installation Wizard .................................... 47 Driver Installation .....................................................................................
Barco Display Tab ............................................................................................. 81 Introduction ................................................................................................... 81 Using The BARCO Display Tab .................................................................... 82 Displays ................................................................................................... 82 Properties ..........................................................
INTRODUCTION System manual Coronis 3MP 7
Introduction (This page intentionally left blank.
Introduction INTRODUCTION BARCO Coronis® is a total display solution for medical applications. Coronis 3MP2FH can be a single-head or multi-head system. Coronis comes with everything you need to set-up a complete viewing system, from cables to displays. Contents of the package Please refer to the packing list on the outside of the Coronis box. Please contact BARCO if the content of the package does not correspond to the list.
(This page intentionally left blank.
IMAGING BOARD INSTALLATION System manual Coronis 3MP 11
Imaging board installation (This page intentionally left blank.
Imaging board installation 3MP2FH PRODUCT OVERVIEW The BarcoMed 3MP2FH Graphics Controller delivers a quality 2048x1536 pixel image with 1024 simultaneous shades of gray for medical imaging applications. Features of the BarcoMed 3MP2FH • Dual Head Configuration • 2048 x1536 resolution at 60 Hz • 10 bit performance on LCD • 32MB Video Memory • Portrait or Landscape Mode • 1024 Simultaneous shades of gray • Hardware cursor • Single slot PCI card • Control Panel supports the English (U.S.
Imaging board installation System Configuration Guidelines Because of the low power consumption and low heat generation of the 3MP2FH, multiple boards may be installed in adjacent PCI slots or adjacent to other PCI boards. Additionally there should be no need to modify either the PC’s power supply and/or cooling system.
Imaging board installation PLANNING YOUR 3MP2FH, 2MP2FH OR 1MP2FH INSTALLATION Important installation considerations Preparations before installation 1 Make certain all equipment is switched off. 2 In case you use a PCI expansion chassis, please install it following the guidelines in its User’s Guide. 3 Familiarize yourself with the 3MP2FH, 2MP2FH or 1MP2FH Display Controller and the cables used to connect it to the display panel. 4 Read through this guide from beginning to end.
Imaging board installation (This page intentionally left blank.
Imaging board installation HARDWARE INSTALLATION Notice: Wear a protective ESD strap during installation or handling of the display controller. Electrostatic charges can damage the display controller. Familiarizing Yourself With the 3MP2FH, 2MP2FH or 1MP2FH Prior to installing your 3MP2FH, 2MP2FH or 1MP2FH display controller(s) in your PC please take a few minutes to familiarize yourself with both the display controller and the PCI slots in your computer.
Imaging board installation Sw itch Function VGA EN Enables VGA on the Pri mary Head (default i s ON). BIOS EN Allows the System BIOS to read the VID EO BIOS (default i s ON). NORMAL C ontrols Board State (default i s ON). INT C LK Internal C lock (default i s ON). The swi tches are i n the ON posi ti on when the whi te sli der swi tch i s posi ti oned towards the top of the board.
Imaging board installation Figure 2: PCI and RAID Controller Slots Installing the BarcoMed 3MP2FH, 2MP2FH or 1MP2FH Display Controller Install the 3MP2FH, 2MP2FH or 1MP2FH into your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord. 2. Remove the chassis cover according to the manufacturer’s instructions. Be sure to observe safety warnings. 3.
Imaging board installation 1MP2FH setup, connect the secondary display to the other connector on the display controller. 7. Reconnect the power cord, turn on the power, and boot the system as usual. Running Multiple BarcoMed 3MP2FH, 2MP2FH or 1MP2FH Display Controllers in a Single Host The physical order of the displays may vary when you are running multiple BarcoMed 3MP2FH, 2MP2FH or 1MP2FH display controllers.
DISPLAY INSTALLATION System manual Coronis 3MP 21
Display installation (This page intentionally left blank.
SAFETY INSTRUCTIONS • Read the safety and operating instructions before operating the apparatus. • Retain safety and operating instructions for future reference. • Adhere to all warnings on the apparatus and in the operating instructions manual. • Follow all instructions for operation and use. •This apparatus conforms to: CE, IEC 60950, UL 60950, CAN/ CSA C22.2 No.
Display installation OVERVIEW Introduction The MFGD 3420, BARCO’s 21” 3 megapixel greyscale LCD display, guarantees perfect image quality in medical imaging applications. The display combines a TFT (thin film transistor) liquid crystal display panel structure and a built-in backlight with inverter for a better picture quality. It is designed to meet the users' needs for performance, consistency, and outstanding image quality through a streamlined development process.
Display installation Package contents The package should include the following items, please check. If some of the items are missing, please contact the reseller you have purchased the unit from.
Display installation (1) Power LED - The LED is off when the display is off. - The LED is green when the display is on. Note: This function can be switched off by software. - The LED is blinking green when the display is in Suspend powersaving mode. - The LED is orange when the display is in Stand-by power-saving mode.
Display installation INSTALLATION Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation in case it is built in a rack or console. • Make sure the computer is switched off before connecting the signals.
Display installation Portrait or landscape position You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables. To change the panel orientation: 1 Stand at the front side of the panel and take the panel at both sides. 2 Very important: Tilt the panel before changing the orientation. Should you change the panel orientation without tilting it first, you might irreversibly damage the tilt & swivel mechanism.
Display installation 3 Route the cable so that it enters the connector compartment at the place where the cover is bulged. To connect the power: 1 Connect the output of the 12V DC power supply to the DC input (6) of the display. 2 Connect one end of the proper power cable to the AC input of the 12V DC power supply. 3 Connect the other end of the power cord to a grounded power outlet. Routing the signal cables After connecting all cables, fix them in the cable tie at the rear of the connector compartment.
Display installation Tilt and swivel positioning Adjust the position of the panel for best viewing conditions. The display foot allows adjusting the panel height, horizontal viewing angle and vertical viewing angle. Starting up Proceed as follows: 1 Switch on the computer. 2 If necessary, select a suitable resolution in the computer operating system. You will have to select a resolution that corresponds to the panel orientation (landscape or portrait).
Display installation OPERATION Switching to stand-by position When the display is on and no on-screen menus are visible, press the control wheel (2) shortly to switch the display in stand-by. When the display is in stand-by, press the control wheel to switch it back on. Controlling the display The control wheel (2) at the bottom (portrait orientation) or at the side (landscape orientation) allows you to perform controls. The control wheel is a rotation - click system.
• - Display installation Some adjustments can be made by changing an adjustment value. To change an adjustment value: Turn the control wheel to select the adjustment. Click the wheel shortly. A pointer appears next to the adjustment name. Turn the wheel to change the value. Click the wheel shortly to confirm the change. The pointer disappears again. • Some adjustments can be made by selecting from a range of predefined settings. To change the selection: - Turn the control wheel to select the adjustment.
Display installation Settings To change the settings: 1 Turn the control wheel to select the setting you wish to change. 2 Click the control wheel to change the setting. The Settings menu contains the following items: DPMS ................... Allows to switch on/off the automatic power saving system (DPMS) Power LED ........... This setting allows you to switch off the power LED. Note: The LED’s orange DPMS state is not influenced by this setting.
Display installation ADVANCED FUNCTIONS About this chapter Important The functions described in this chapter are intended for trained service staff only! Improper use of these functions may irreversibly damage the display. BARCO cannot be held responsible for the results or damage caused by improper use of these functions. This chapter describes only the Advanced functions in the OSD menus. For a description of the other functions (standard functions), please refer to the previous chapter, Operation .
Display installation Advanced functions in the Luminance menu The Luminance menu contains the following advanced function: Manual Backlight ..... This function allows to manually control the backlight luminance. When you control the Manual Backlight function, the Luminance target function and I-Guard control are disabled. Important: Disabling the I-Guard results in an uncalibrated and not stabilized backlight.
Display installation Advanced functions in the Information menu In Advanced mode, the Information menu contains the following additional submenus: Service, Firmware, Runtime, Measurements and Scan Measurements. Service The Service info menu contains the following items: Display Name .......... The display type Display Ser No ........ Indicates the display serial number Display Stock No ..... Indicates the display order number Panel Ser No ...........
Display installation Measurements The Measurements info menu contains the following items: Internal Temperature .... The temperature measured inside the display Sensor Temperature .... The internal temperature measured on the IGuard board FAN speed ................... A value indicating the speed of the fans. Minimum speed is 0, maximum speed is 1000 Sensor Y value ............. The luminance measured by the I-Guard, expressed in nit (Cd/m²) Sensor DAC value .......
Display installation Advanced functions in the Adjustments menu In Advanced mode, the main menu contains an additional menu, Adjustments. This menu contains the submenu Miscellaneous. Miscellaneous Adjustments The Miscellaneous menu contains the following items: RS232 Address ....... Turn the control wheel to change the internal display address.
Display installation MAINTENANCE Panel Take care not to damage or scratch the panel. Clean with a soft woolen or cotton towel. Use a watery solution or a mild commercial glass-cleaning product. Cabinet Do not use chemical cleaning products, benzene, toluene, xylene or other solvents. Clean with a soft cloth dampened with mild detergent and water. Repeat with water only and wipe dry with a dry cloth.
Display installation TROUBLESHOOTING Windows does not show the desired display settings Should you have problems selecting display settings for portrait oriented displays in the Windows Display Properties control panel, disable the option Hide modes that this monitor cannot display in the control panel (see below). Information: The display contains a special memory chip that contains information about the display's scanning capabilities.
Display installation TECHNICAL SPECIFICATIONS Picture panel 20.8-inch diagonal viewable screen TFT (thin film transistor) active matrix, greyscale liquid crystal display Resolution Native: 2048 x 1536 Other VESA resolutions possible, not scaled Display area (H x V) 423.9 x 318 (mm) Pixel Pitch 0.207 mm (H) x 0.
Display installation Power source Input for 12 VDC power supply unit: 90 ~ 264 VAC Input for display: 12 VDC. (The supplied 12VDC power supply must be used) Power consumption 80 watts (max.) Safety standards CE, IEC 60950, UL 60950, CAN/CSA C22.2 No.
BARCOMED SOFTWARE DRIVER INSTALLATION System manual Coronis 3MP 43
BarcoMed software driver installation (This page intentionally left blank.
BarcoMed software driver installation SOFTWARE INSTALLATION Overview The BarcoMed Software Installation section has been divided into two sections. One for Windows NT 4.0 and the other for Windows 2000 and Windows XP. Software In addition to the device drivers for your BarcoMed Display Controller(s), your BarcoMed Software CD also includes several additional tools. They are: the BarcoMed Driver Tab, the BarcoMed Hardware Tab, the BARCO DPMS Screen Saver and the CORONIS Rotation Service.
BarcoMed software driver installation Service in a single operation prior to rebooting. The user may also use the BarcoMed Software Installation Wizard to reinstall either the BarcoMed Display Controller Drivers or CORONIS Rotation Service and/or modify, repair or remove the BARCO DPMS Screen Saver from his system. The BarcoMed Display Controller Driver must be installed prior to installing either or both the BARCO DPMS Screen Saver or the CORONIS Rotation Service.
BarcoMed software driver installation SOFTWARE INSTALLATION Installing the BarcoMed 3MP2FH, 2MP2FH or 1MP2FH Windows NT 4.0 Software SPECIAL NOTE: Prior to installing the BarcoMed drivers and related software you MUST install the BarcoMed Display Controller(s), connect the CORONIS display panel(s) to the controller(s), and turn the CORONIS display panel(s) on.
BarcoMed software driver installation Figure 4 If it determines that the Microsoft Installer is either out of date or missing, it will display the screen shown in figure 5. Click “OK” to continue, the wizard will then install a newer version of the Microsoft Installer. Figure 5 The BarcoMed Product Installation Wizard will advise you when it has successfully installed the new version of the Microsoft Installer. Click “OK”. The Wizard may prompt you to restart your system.
BarcoMed software driver installation checkbox next to it. When you have finished selecting the BarcoMed Software you wish to install, click “Install” on the Wizard’s Welcome Screen to continue or “Cancel” to exit the wizard. Driver Installation 5. Click “Next” on the Display Driver Wizard’s Welcome Screen to continue or “Cancel” to exit the Display Driver Wizard and return to the Software Install Wizard. 6. The Device Selection Screen (figure 6 below) shows the devices supported by the driver on the CD.
BarcoMed software driver installation 7. The Device Confirmation Screen lists the device that will be installed. If you want to change your selection, click “Back” and you will see the previous screen. To begin installation, click “Next”. If you want to end the installation without installing the driver, click “Cancel” and the Wizard will exit. Caution: Once you click “Next”, you cannot cancel the driver installation. 8.
BarcoMed software driver installation Figure 8 10. The “Customer Information” screen will appear. The Installer will automatically fill in the blanks using the information entered when Windows was installed on your system. You may change this information if you wish. Click “Next” to continue. 11. The “Setup Type” page will now appear. Choose “Typical” to install the default schemes with English names. Choose “Custom” to install the default schemes with either Dutch or German names.
BarcoMed software driver installation or click “Back” to return to the Welcome Screen of the BarcoMed Product Install Wizard to select additional software to install. If you click “Finish” Windows may prompt you to restart your system, if it does click “Yes”.
BarcoMed software driver installation 19. When your computer restarts, select “NT Version 4.0 (VGA Mode)”. Log in using an account with administrator privileges and set the resolution of your CORONIS Display Panel(s). Setting the Resolution of Your CORONIS Display Panel 1. After you have logged in using an account with administrator privileges per step 19 above, Windows NT will launch the “Invalid Display Settings” dialog box, Click “OK”. 2. Windows will launch the “Display Properties Contol Panel”.
BarcoMed software driver installation for less than the maximum number of displays supported by your configuration. (See table on following page for examples.
BarcoMed software driver installation Reinstalling the BarcoMed Driver To reinstall only the BarcoMed Driver, follow the steps described in the section “Using the BarcoMed Product Installation Wizard” with the following changes. 1. Skip Step 1. 2. In Step 4, clear the checkboxes next to the BARCO DPMS and the CORONIS Rotation Service. 3. When the driver has finished installing, click “Finish”. Then click “Quit”. Reboot the system when prompted and then reset the resolution of your displays if necessary.
BarcoMed software driver installation Installing the BarcoMed 3MP2FH, 2MP2FH or 1MP2FH Windows 2000 or Windows XP Software Using the BarcoMed Product Installation Wizard SPECIAL NOTE: Prior to installing the BarcoMed drivers and related software you MUST install the BarcoMed Display Controller(s), connect the CORONIS display panel(s) to the controller(s), and turn the CORONIS display panel(s) on.
BarcoMed software driver installation The BarcoMed Product Installation Wizard will begin by inspecting your system to make certain that all of the Windows components it needs are up to date. If they are, the BarcoMed Product Installation Wizard will display the BarcoMed Product Installation Wizard’s welcome screen (figure 10 below). Figure 10 If it determines that the Microsoft Installer is either out of date or missing, it will display the screen shown in figure 11 below.
BarcoMed software driver installation finds in your system. Click “Cancel”. Continue to click “Cancel” until Windows stops launching the “Found New Hardware Wizard Video Controller”. Again, please be patient as Windows will again scan its library of Plug-and-Play device drivers to see if it has a driver for your BarcoMed display controller The BarcoMed Product Installation Wizard’s welcome screen will now be displayed.
BarcoMed software driver installation 8. Your selection on the “Enable DualView” screen (figure 13 below) determines if DualView is enabled or not. DualView allows a dual head display controller to display two separate desktops, one for each display instead of a single virtual desktop that spans across both displays. Figures 14 and 15 on the next page shows the difference between running with DualView enabled or disabled.
BarcoMed software driver installation Figure 14: DualView Disabled Figure 15: DualView Enabled System manual Coronis 3MP 60
BarcoMed software driver installation Special Note: If you installed the drivers with DualView disabled, Windows will still show two devices installed for each BarcoMed Display Controller installed under “Display Adapters” in the “Device Manager Control Panel”. The second device will be disabled. This is normal. Do NOT try to enable any of the disabled display adapters. 9. The “Device Confirmation” screen displays the device driver that will be installed.
BarcoMed software driver installation Figure 17: Windows XP Windows Logo Testing Warning 11. When the screen shown in figure 18 below appears select the palette mode you wish to use and if you want to enable DirectDraw and click “Next”. Figure 18 12. When the Driver Install Wizard tells you that it has successfully installed the selected driver, click “Finish”. The wizard will now begin installing the next selected piece of BarcoMed Software.
BarcoMed software driver installation If the installation of the products you selected at the beginning is complete, click “Finish” to exit the BarcoMed Product Install Wizard or click “Back” to return to the Welcome Screen of the BarcoMed Product Install Wizard to select additional software to install. When you click “Finish” Windows may prompt you to restart your system, if it does click “Yes”.
BarcoMed software driver installation 14. The “Customer Information” screen will appear. The Installer will automatically fill in the blanks using the information entered when Windows was installed on your system. You may change this information if you wish. Click “Next” to continue. 15. The “Setup Type” page will now appear. Choose “Typical” to install the default schemes with English names. Choose “Custom” to install the default schemes with either Dutch or German names.
BarcoMed software driver installation 19. The CORONIS Rotation Service must be installed on a local hard drive in order for it to function correctly. We recommend that you install it in the default location: C:\WINNT (Windows 2000) or C:\Windows (Windows XP). If you wish to install the CORONIS Rotation Service in a different location use the “browse” button on the Install Location Screen of the CORONIS Rotation Service InstallShield Wizard. Click “Next” to continue the installation. 20.
BarcoMed software driver installation mode with NO system colors. This guarantees that the all of the 256 gray levels available for GDI graphics will be present, and also eliminates the danger that colors will change when focus moves among different applications. However, if you are using the Color to Gray Conversion Palette mode, the color setting for your high-resolution grayscale displays should default to True Color (32 bits per pixel).
BarcoMed software driver installation If you have a single display configuration and you have enabled DualView, Windows will not allow you to attach the second head. This is normal and not a bug. 2. For the display which is still attached click on the “Advanced” Button. 3. Select the “Adapter” tab and then click on the “List All Modes...” button. Select the resolution and refresh rate that your Coronis display supports from the dialog box and click “OK”.
BarcoMed software driver installation (This page intentionally left blank.
BarcoMed software driver installation BARCOMED DRIVER TAB Introduction After the BarcoMed Windows Display Controller Driver is installed, a new Display Properties tab is available for configuring special features of the BarcoMed Display Controller. Please note that you must have logged on to Windows using an account with administrator privileges in order to use the BarcoMed Tabs of the Windows Display Properties Control Panel to change any display settings.
BarcoMed software driver installation Figure 21: BarcoMed Driver Tab under Windows 2000 and Windows XP Status Displays the current BarcoMed Display Controller, driver, and the currently selected display resolution. Graphics Board This displays the current BarcoMed Display Controller. Driver Version This displays the current BarcoMed driver version. Resolution This displays the currently selected display resolution.
BarcoMed software driver installation using one of Barco’s three “Standard 8-bit (256-color)” palette modes. All applications that are designed to work correctly with 8-bit (256color) modes should continue to work normally. Please note that dithering is not used while in this mode. The Enable Dithering check box will be grayed-out, and dithering will be automatically disabled regardless of whether this check box is checked. This complies with the Windows standard interface method.
BarcoMed software driver installation Please note that dithering is not permitted while in this mode. The Enable Dithering check box will be grayed-out, and dithering will be automatically disabled regardless of whether this check box is checked. This complies with the Windows standard interface method. If you are unsure whether or not your application requires this “Static Gray Palette including Standard System Colors” mode, contact your application provider.
BarcoMed software driver installation Drawing Modes You may choose one or both of the following Drawing Modes: Enable DirectDraw This option allows the user to enable or disable DirectDraw. DirectDraw is a software interface that provides direct access to display devices while maintaining compatibility with the Windows graphics device interface (GDI). DirectDraw provides a deviceindependent way for applications to gain access to the hardware features of specific display devices.
BarcoMed software driver installation If “Custom Configuration” is displayed, it means that the current monitor configuration was set via the registry and it doesn’t agree with any of the configurations that the display control panel supports. Contact BarcoView Medical Imaging Systems for further information. Under Window 2000 or Windows XP you may also enable or disable DualView through the Monitor Configuration drop down menu.
BarcoMed software driver installation BARCOMED HARDWARE TAB Introduction The BarcoMed Hardware Tab is used for gathering information about BarcoMed Display Controller(s). For all BarcoMed Display Controller(s) it will display PCI information. In addition for BarcoMed Display Controller(s) based on the AURA video chipset it will also display information about the Firmware installed on the board.
BarcoMed software driver installation To access the BarcoMed Hardware Tab do the following: 1. Open the “Display Properties Control Panel” by right clicking on the desktop, then select “Properties”. 2. Under Windows NT 4.0, Click on the “BarcoMed Hardware Tab” (see figure 22 below). Under Windows 2000 and Windows XP, click on the “Settings” tab. Double click on the rectangle that represents the BarcoMed Display Controller to bring up its property page.
BarcoMed software driver installation Figure 23: BarcoMed Hardware Tab under Windows 2000 and Windows XP Using The BarcoMed Hardware Tab Device Displays the current BarcoMed Display Controller, driver, and the currently selected display resolution. Identify Device: This button is for BarcoView Medical Imaging Systems (MIS) internal use only and is grayed out.
BarcoMed software driver installation PCI Information Device ID: Displays the device’s PCI Device ID number. Vendor ID: Displays the device manufacturer’s PCI Vendor ID number. Subsystem ID: Displays the device’s PCI Subsystem ID number. SubsystemVendorID: Displays the device’s PCI Subsystem Vendor ID number. VGA Status: Displays whether the VGA capabilities of the BarcoMed controller are enabled or disabled.
BarcoMed software driver installation “Update Device...” Button: Clicking this button will run the BarcoMed Hardware Configuration Wizard. This program allows the user to flash update the firmware stored in the ROM of the currently selected BarcoMed Display Controller. The BarcoMed Hardware Configuration Wizard is a “wizard style” application that uses dialog boxes to guide the user through the flash update procedure.
BarcoMed software driver installation (This page intentionally left blank.
BarcoMed software driver installation BARCO DISPLAY TAB Introduction The BARCO Display Tab is used for gathering information about the BarcoMed Flat Panel Display(s). To access the BARCO Display Tab do the following: 1. Open the “Display Properties Control Panel” by right clicking on the desktop, then select “Properties”. 2. Under Windows NT 4.0, Click on the “BARCO Display Tab” (see figure 24 below). Figure 24: BARCO Display Tab under Windows NT 4.
BarcoMed software driver installation Under Windows 2000 and Windows XP, click on the “Settings” tab. Double click on the rectangle that represents the BarcoMed Display you are working with to bring up its properties page. Click on the “BARCO Display” tab (figure 25).
BarcoMed software driver installation to include each display, otherwise those ports will not be visible to the BARCO Display Tab. Hovering the cursor over a display icon will pop up a window with information that identifies the display. Properties You may acess the Properties page of the currently selected display, which is represented by the monitor icon above with the black frame around it, by either clicking on the “Properites” button or double clicking on the icon.
BarcoMed software driver installation Figure 26 System manual Coronis 3MP 84
BarcoMed software driver installation BARCO DPMS SCREEN SAVER OVERVIEW Introduction The BARCO DPMS (Display Power Management Signaling) Screen Saver allows the user to set power and display saving features for medical displays driven by BarcoMed Display Controllers. At the end of the work day, the display will enter certain DPMS states as requested by the display controller. The default state for the BARCO DPMS Screen Saver is the Off state.
BarcoMed software driver installation BARCO DPMS Screen Saver Options From the “BARCO DPMS Screen Saver Control Panel” you can change many DPMS screen saver elements simultaneously. The DPMS screen saver elements in each scheme are work schedule, work day screen saver, DPMS settings after work day, and many additional options. Current Scheme Lists the three “DEFAULT” schemes which you can use as they are. Or you can modify them to meet your office’s schedule.
BarcoMed software driver installation Screen Saver During Work Day On CRT based displays, such as the Barco MGD series, a “regular” screen saver can be invoked during user inactivity during the work day. This “regular” screen saver and its settings can be chosen from the “Screen Saver During Work Day” section. We recommend using an all black screen saver, such as the “Barco Metheus Blank Screen” saver, for the longest phosphor life.
BarcoMed software driver installation DPMS State Pow er Savings Monitor Recovery Time On None N/A Stand-by Minimal Short Suspend Substantial Longer Off Maximum Longest Monitor Settings Select the amount of time the display requires to warm-up. Since all CRT based displays require some warm-up time before they are at full performance, this ensures that the display is ready for use at the beginning of the work day. If you have a Barco Medical Display, select “Barco Quick Start.
BarcoMed software driver installation privileges. If a user who does not have administrator privileges tries to save a scheme using an existing default scheme name, an error message is displayed saying “you must have administrator rights to modify a default scheme.” If an administrator saves a scheme using an existing default scheme name, a message is displayed to tell the user that the modification is saved to a default scheme and will be visible to all users.
BarcoMed software driver installation Figure 27: Windows NT 4.
BarcoMed software driver installation Figure 29: Windows XP Screen Saver Tab 3. Click on the “Settings” button. The “BARCO DPMS Screen Saver Control Panel” will open (figure 30 below).
BarcoMed software driver installation 4. Use the default schemes by selecting one of the three default schemes. Click “OK”. Then Click “OK” again. Note: If you make any changes to any of the settings of one of the three default schemes, the Current Scheme field will blank and you MUST SAVE your changes by clicking on the “Save As ...” button. When you click on the “Save As ...
BarcoMed software driver installation after the time specified has elapsed when you are in Stand-By or Suspend, you will automatically go into the Off state. 8. Select the amount of time it takes for your display to warm up. If you have a Barco Medical Display, select “Barco Quick Start”. If you are using a non-Barco display, select the amount of time it takes your display to warm up via the “Monitor Setting” section. Contact your display vendor for this warm-up time.
BarcoMed software driver installation Figure 32 4. Click “Remove” on the Remove Program Screen of the Wizard. 5. When the Wizard has finished removing the program, click “Finish” on the InstallShield Wizard Completed Screen of the Wizard. 6. Click “Quit” to exit the BarcoMed Product Installation Wizard.
BarcoMed software driver installation CORONIS ROTATION SERVICE Overview Special Note: The CORONIS Rotation Service is only available for systems which have the Portrait Accelerator in the CORONIS Display Panel and BarcoMed Display Driver releases that include the CORONIS Rotation Service. The CORONIS Rotation Service may not be available for your system.
BarcoMed software driver installation Rotation Service will change the resolution for both of the CORONIS displays connected to that BarcoMed Display Controller and you will need to change the physical orientation of the second display to match the orientation of the first display.
MEDICAL SOFTWARE INSTALLATION AND USAGE System manual Coronis 3MP 97
MediCal software installation and usage (This page intentionally left blank.
MediCal software installation and usage MEDICAL SOFTWARE INSTALLATION Install MediCal on the PC. Follow the instructions from the MediCal User Guide. Important: Do not forget you have to have Administrator privileges to install or uninstall MediCal. USING MEDICAL You can now use MediCal to configure the complete configuration and set up the Q/A tasks. Proceed as follows: 1 Start MediCal. If appropriate, you can connect to MediCal Administrator.
MediCal software installation and usage (This page intentionally left blank.
