^`pJOMQU rëÉêÛë=dìáÇÉ • • Manual #: 26-0603000-00 Revision: 01
^`pJOMQU==√==rëÉêÛë=dìáÇÉ `çéóêáÖÜí © Barco. September 6, 2007 All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. kçíáÅÉ Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose.
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.
léÉê~íçêë=p~ÑÉíó=pìãã~êó The general safety information in this summary is for operating personnel. aç=kçí=oÉãçîÉ=`çîÉêë=çê=m~åÉäë There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
qÉêãë=få=qÜáë=j~åì~ä=~åÇ=bèìáéãÉåí=j~êâáåÖ= t^okfkd Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly observed, could result in injury to or death of personnel. Note Highlights an essential operating procedure, condition or statement. `^rqflk The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
`Ü~åÖÉ=eáëíçêó The table below lists the changes to the ACS-2048 User’s Guide. Table 0-1. Change History Rev 01 6 Date 9/6/07 ECP # 549078 Description ACS-2048 User’s Guide Approved By R.
q~ÄäÉ=çÑ=`çåíÉåíë `Ü~éíÉê=N fåíêçÇìÅíáçå =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=NN In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Use This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Navigating . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Quick Function Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In Auto Acquire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Via FTP Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Via Web Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Upgrade Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Ethernet Communication . . . . . . . . . . . . . . . . . . . . .
Table of Contents OMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OCSAV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TRNTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VFDBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUTOSAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NK==fåíêçÇìÅíáçå få=qÜáë=`Ü~éíÉê This chapter is designed to introduce you to the ACS-2048 User’s Guide. Areas to be covered are: • • • • • • Chapter Structure How to Use This Guide Conventions About the ACS-2048 Connectivity Diagram Application Questions `Ü~éíÉê=píêìÅíìêÉ The following chapters provide instructions for all aspects of ACS-2048 operations: • Chapter 1, “Introduction” provides a system overview, a list of features, and a system connectivity diagram.
NK==fåíêçÇìÅíáçå How to Use This Guide eçï=íç=rëÉ=qÜáë=dìáÇÉ This section provides important tips for streamlining your use of this User’s Guide in its electronic “PDF” form. k~îáÖ~íáåÖ Use Acrobat Reader’s “bookmarks” to navigate to the desired location. All chapter files have the same bookmark structure for instant navigation to any section. Please note: • • Extensive hyperlinks are provided within the chapters.
NK==fåíêçÇìÅíáçå About the ACS-2048 ^Äçìí=íÜÉ=^`pJOMQU The following topics are discussed in this section: • • • Overview Features A Word About HDCP lîÉêîáÉï As the ideal peripheral for all Barco digital cinema installations, ACS-2048 is an 8 x 1 video switcher that accepts "universal" input formats, and outputs up to 12-bit DVI at 2048 x 1080. With a high-quality scaler at its core, upconverting any input format is as simple as "auto-acquiring" and selecting the desired input.
NK==fåíêçÇìÅíáçå About the ACS-2048 • Provides low video delay: ~ For interlaced sources, maximum video delay is 5 fields total from input to screen (3 in ACS-2048 + 2 in Projector). ~ For progressive sources, maximum video delay is 4 fields total from input to screen (2 in ACS-2048 + 2 in Projector).
NK==fåíêçÇìÅíáçå Connectivity Diagram `çååÉÅíáîáíó=aá~Öê~ã The figure below illustrates a basic ACS-2048 system. Media Server HD-SDI ACS-2048 DVI Barco DP Series Projector HD-SDI / SDI DVI DVI Analog Analog Composite S-Video Option Figure 1-1. Block diagram, ACS-2048 system In the diagram: • • Your selected media server connects to the Barco projector via dual-link HD-SDI.
NK==fåíêçÇìÅíáçå Application Questions ^ééäáÅ~íáçå=nìÉëíáçåë At Barco, we take pride in offering unique solutions to demanding technical problems. If you have application questions, require further information or would like to discuss your application requirements in more detail, please call (866) 469-8036. Our Customer Support Engineers will be happy to supply you with the support you need. Refer to Appendix C, “Contact Information” on page 107 for details.
OK==e~êÇï~êÉ=lêáÉåí~íáçå få=qÜáë=`Ü~éíÉê This chapter provides detailed diagrams of the ACS-2048’s front and rear panels, along with comprehensive explanations of each.
2. Hardware Orientation ACS-2048 Front Panel ^`pJOMQU=cêçåí=m~åÉä The figure below illustrates the ACS-2048 front panel: 8 ACS-2048 MAIN MENU > In Auto Acquire Input Output 3 6 5 SEL ON >> >> ACS-2048 ESC Adjust Input 3 DVI / RGBHV Input 6 Input 5 CVBS Inputs 1 HD/SD SDI 2 DVI-I 3 DVI-I 4 Analog HD-15 5 Analog 5-BNC Input 1 6 CVBS 7 Y/C 8 Option TEST PAT 9 SD/HD SDI 1 Input 2 Input 4 DVI / RGBHV RGBHV / YUV 2 H/C V R/Pr G/Y Input 7 Y/C B/Pb 4 7 Figure 2-1.
2. Hardware Orientation ACS-2048 Front Panel 4) Input 4 Connector One HD-15 connector is provided for Input 4, which corresponds to the fourth button in the Inputs Section. The input is dedicated to YUV or RGBHV formats. Please note: ~ ~ This input provides 10-bits/color sampling at a maximum 170 MHz. This input supports 1:1 sampling up to 1600x1200@60 Hz. Sources with native pixel rates greater than 170 MHz will be filtered and undersampled at 170 Mhz. These include: • 1920x1080p@60 (173.
2. Hardware Orientation ACS-2048 Front Panel aáëéä~ó=pÉÅíáçå The figure below illustrates the Display Section: ACS-2048 MAIN MENU > In Auto Acquire Input Output SEL ON >> >> Adjust ESC Figure 2-2. Display Section with Main Menu Descriptions of each button and control are provided below: • The Menu Display is a 4 line x 20 character Vacuum Fluorescent Display (VFD) that shows all ACS-2048 menus and sub-menus. Brightness is adjustable.
2. Hardware Orientation ACS-2048 Front Panel fåéìíë=pÉÅíáçå The figure below illustrates the Inputs Section: Inputs 1 HD/SD SDI 2 DVI-I 3 DVI-I 4 Analog HD-15 5 Analog 5-BNC 6 CVBS 7 Y/C 8 Option TEST PAT Figure 2-4. Inputs Section The buttons in the Inputs Section enable you to select system inputs, or the built-in test pattern. There are four button states: • Off — indicates that sync has not been detected on the input connector, and the input cannot be used on air.
2. Hardware Orientation ACS-2048 Front Panel • 3 — selects a digital DVI or analog RGBHV input (the front panel Input 3 connector) as the source. • 4 — selects a YUV or RGBHV input (the front panel Input 4 connector) as the source. • 5 — selects a YUV or RGBHV input (the front panel Input 5 connector) as the source. • 6 — selects a Composite NTSC or PAL input (the front panel Input 6 connector) as the source.
2. Hardware Orientation ACS-2048 Rear Panel ^`pJOMQU=oÉ~ê=m~åÉä The figure below illustrates the ACS-2048 rear panel: Model ACS-2048 100 - 240 VAC 50 – 60 Hz, 1.0A 10/100 BASE-T DVI OUT B A 2 1 3 Figure 2-1. ACS-2048 Rear Panel 1) DVI Outputs 2) Ethernet 3) AC Power Following are descriptions of each rear panel connector: 1) DVI Outputs Two DVI-D connectors (A and B) are provided for the system’s dual-channel (Twin-Link) DVI output.
2. Hardware Orientation ACS-2048 Rear Panel 3) AC Power One AC Connector is provided for connecting ACS-2048 to AC. The integral switch turns the chassis on and off. In Appendix A, refer to the “Physical and Electrical Specifications” section on page 84 for power details.
PK==fåëí~ää~íáçå få=qÜáë=`Ü~éíÉê This chapter provides detailed instructions for installing the ACS-2048 hardware.
3. Installation Safety Precautions p~ÑÉíó=mêÉÅ~ìíáçåë= For all ACS-2048 installation procedures, observe the following important safety and handling rules to avoid damage to yourself and the equipment: • To protect users from electric shock, ensure that the power supplies for each unit connect to earth via the ground wire provided in the AC power cord. • The AC Socket-outlet should be installed near the equipment and be easily accessible. råé~ÅâáåÖ=~åÇ=fåëéÉÅíáçå= Inspect the shipping box for damage.
3. Installation Rack-Mount Installation o~ÅâJjçìåí=fåëí~ää~íáçå ACS-2048 units are designed to be rack mounted and are supplied with front rack-mount hardware. Please note the following important points: • When rack mounting the unit, remember that the maximum ambient operating temperature for the unit is 40 degrees C. • Leave sufficient front and rear space to ensure that the airflow through the fan and vent holes is not restricted.
3. Installation Power Installation mçïÉê=`çêÇLiáåÉ=sçäí~ÖÉ=pÉäÉÅíáçå ACS-2048 is rated to operate with the following specifications: • • Input Power: 100-240 VAC, 50-60 Hz Power Consumption: 240 watts maximum ACS-2048 performs line voltage selection automatically, and no user controls are required. The AC power cords must be accessible so that they can be removed during field servicing.
3. Installation Signal Installation páÖå~ä=fåëí~ää~íáçå The figure below illustrates a sample ACS-2048 system diagram. Use this figure for reference during the signal installation process. Sample Source Input Devices Input 1 (HD/SD SDI) Input 2 (DVI) Input 3 (DVI) Input 4 (Analog) Input 5 (Analog) Input 6 (Composite) Input 7 (S-Video) ACS-2048 DVI Out A DVI Out B Barco DP Series Projector Ethernet Switch Figure 3-2.
3. Installation Format Connection Table 2. 3. Output connections: a. If you are operating the ACS-2048 in 10-bit or 12-bit mode, connect both DVI outputs (A and B) to the projector’s DVI inputs A and B. b. If you are operating the ACS-2048 in 8-bit mode, connect DVI output A to the projector’s DVI input A. Communications connection: a. Connect the ACS-2048’s Ethernet port to an Ethernet switch, and connect the switch to the other Ethernet devices in your local system (e.g., laptop, projector, etc.).
QK==léÉê~íáçå få=qÜáë=`Ü~éíÉê This chapter provides comprehensive menu descriptions and detailed operating instructions for the ACS-2048.
4. Operation Control Overview `çåíêçä=lîÉêîáÉï There are several ways to control the ACS-2048: • The front panel is ideal for all basic system configurations. Available controls include the Display Section and the buttons in the Inputs Section. • The ACS-2048 can also be controlled remotely via Ethernet. All system commands are available.
4. Operation Quick Setup and Operations ACS-2048 Ba rco Ve rsion 1. 00 Initializing ... Figure 4-4. System initialization message 4 The “version” line in the above menu shows the software version that is currently being executed. This version number will change as software upgrades are released. nìáÅâ=pÉíìé=~åÇ=léÉê~íáçåë For the optimum speed in system setup and operations, use the following steps. For reference, links are provided to pertinent sections in this guide. 1.
4. Operation Quick Setup and Operations 10. Connect inputs — Connect all inputs to the ACS-2048, and check for the proper backlight, which indicates that sync is detected. (Chapter 3, “Signal Installation” on page 29. This chapter, “Understanding Backlighting” on page 68.) 11. Select and adjust inputs — As required, select an input, and perform the necessary adjustments, such as crop, brightness, contrast, color balance, and timing. (This chapter, “Input Menu” on page 43.) 12.
4. Operation Menu Tree jÉåì=qêÉÉ The figure below illustrates the entire ACS-2048 menu tree. Please use this diagram for reference as you learn how to operate the system.
4. Operation Using the Menu System rëáåÖ=íÜÉ=jÉåì=póëíÉã This section lists the rules and conventions for using ACS-2048’s menu system. For reference, the figure below illustrates the Main Menu: ACS-2048 MAIN MENU > In Auto Acquire Inpu t Output ON >> >> Figure 4-6. Main Menu Display Please note the following important menu rules and conventions: • • The top line names the current menu, in all capital letters.
4. Operation Using the Menu System • To navigate back up the menu structure, press ESC. Each press takes you back up the menu tree by one level. • The SEL button is also used to answer “Yes” to certain menu queries. The ESC button is also used to answer “No” to certain menu queries. Note • The display itself is four lines high, and the ADJUST knob is used to scroll through the various lines. Throughout this chapter, entire menus will be shown for clarity — rather than a series of four-line sections.
4. Operation Quick Function Reference nìáÅâ=cìåÅíáçå=oÉÑÉêÉåÅÉ Use the following table to quickly access the proper menu for a specific function. Both hyperlinks and page numbers are provided. Table 4-1.
4. Operation Quick Function Reference Table 4-1.
4. Operation Quick Function Reference Table 4-1.
4. Operation Using the Main Menu rëáåÖ=íÜÉ=j~áå=jÉåì After ACS-2048 initialization is complete, the Main Menu appears. This is the system’s top-level menu. Note When you make changes to input, output and system parameters, this “configuration” information can be stored in non-volatile memory — provided that the user performs a “Save Config” operation. These settings will be automatically recalled each time the unit is turned on.
4. Operation Using the Main Menu få=^ìíç=^ÅèìáêÉ From the Main Menu, select In Auto Acquire to enable or disable the Input Auto Acquire mode. Values are: OFF and ON (default). • When Input Auto Acquire is ON, the system always performs a full sync acquisition on the selected input signal under the following conditions: ~ ~ ~ ~ • When an input channel without a saved configuration file is selected. When the input type is changed. When the input signal changes sync rates.
4. Operation Using the Main Menu fåéìí=jÉåì From the Main Menu, select Input to display the Input Menu. The selected input button is shown on the top line. INPUT 1024x76 8 @59. 94 > T ype Co lorspace Image Adjust Co ntrast Brightness Color Balance Timing Adjust Processing Save Con fig Re se t Config Delete Config [Analog] R GB >> 100. 0% 100. 0% >> >> >> Figure 4-8. Input Menu (sample) The Input Menu enables you to set configuration options for the selected input channel.
4. Operation Using the Main Menu fåéìí=cçêã~í From the Input Menu, select the top Input Format line to view the “auto-acquired” format for the selected input, or to change the format. The format is shown in the following form: Hact x Vact @ Vr Hz S 1024x768@59.94 Please note the following important points: • If you select an input and it does not have a valid input signal, the "Invalid Selection, No Sync Detected" message is displayed.
4. Operation Using the Main Menu Please note: • If a source type is chosen and a correct signal cannot be detected, the Input Format field (in the Input Menu and the Status Menu) indicates “Invalid Signal.” • For inputs 2 and 3, analog signals can be connected to the ACS-2048 using a customer-supplied DVI to HD-15 adaptor. `çäçêëé~ÅÉ From the Input Menu, select Colorspace to change the color space for the selected input.
4. Operation Using the Main Menu fã~ÖÉ=^Çàìëí From the Input Menu, select Image Adjust to display the Image Adjust Menu. This menu enables you to adjust input parameters such as crop, pan and aspect ratio: I MA G E A D JU S T > Aut o Config H Cr op V Cro p H Pan V Pan Aspe ct Ra tio Ra tio 0 0 [0] [0] Custom 1.3 30 Figure 4-9. Image Adjust Menu (sample) • Select Auto Config to perform an automatic input configuration on the selected source.
4. Operation Using the Main Menu ~ Adjustment range: 0.750 to 3.000. Note that the default value depends on the last Aspect Ratio selected before Custom was chosen. Note The ACS-2048 selects and displays the input video aspect ratio according to the input format detected.
4. Operation Using the Main Menu • • Default (all values): 0.0% Select Reset All to set all values back to their default settings. eìÉLp~íìê~íáçå=`çäçê=_~ä~åÅÉ=jÉåì If the current input’s type is set to Composite, S-video, YPbPr, or SDI, the Hue/ Saturation Color Balance Menu appears: CO L O R B A L A N C E > Hu e Sat urat i on Re se t A l l 100 0 Figure 4-11. Hue/Saturation Color Balance Menu (sample) Please note: • Hue is measured in degrees, and is [N/A] for YPbPr inputs.
4. Operation Using the Main Menu Select Auto Config to perform an automatic input configuration on the selected source. • • Note In this mode, for the selected image, the system finds the first and last pixel on each edge, and ensures (to the best possible extent) that the entire image is visible. In addition, if the input is analog, the system automatically phases the input to determine the correct sampling phase.
4. Operation Using the Main Menu mêçÅÉëëáåÖ From the Input Menu, select Processing to display the Processing Menu: PR O CE SS I NG > Sync Sel Pulld own Comp Sync Slice (mV) Au to OFF 128 Figure 4-13. Processing Menu (sample) The following functions are available: • Sync Selection — This function applies only to Analog RGB inputs. The digital input sources have embedded syncs, and the composite, S-video, and YPbPr inputs always take sync from the Y (or composite) channel.
4. Operation Using the Main Menu p~îÉ=fåéìí=`çåÑáÖ From the Input Menu, select Save Config to save the input configuration for the currently selected input. A confirmation message is briefly displayed, after which the system returns to the Input Menu. Savin g Inpu t Config Figure 4-14. Saving Input Configuration Message Please note the following important points regarding input configuration files: • The ACS-2048 supports one Input Configuration File for each physical input.
4. Operation Using the Main Menu aÉäÉíÉ=`çåÑáÖ From the Input Menu, select Delete Config to delete the input configuration for the currently selected input. When you select the function, you will be prompted to delete (SEL) or continue without deleting (ESC). If you elect to delete, a confirmation message is briefly displayed, after which the system returns to the Input Menu. De leting I nput Conf ig Figure 4-16.
4. Operation Using the Main Menu lìíéìí=jÉåì From the Main Menu, select Output to display the Output Menu, which enables you to configure the outputs of the ACS-2048. OUTPUT > Output Mode Gamma Test Patt ern Output Adju st Save Con fig 204 8x1080p @50 10 bits 0.0 >> >> Figure 4-17.
4. Operation Using the Main Menu • Connector B: To increase color depth, 10-bit or 12-bit output mode can be selected on this connector. d~ãã~ From the Output Menu, select Gamma to specify the Gamma associated with the current output. • • Adjustment range: 1.0 to 3.0, in steps of 0.1 Default: 1.0 qÉëí=m~ííÉêå From the Output Menu, select Test Pattern to display the Test Patterns Menu: TE ST P AT TERNS > Mode T ype Ra st er B ox ON Bu rst OFF Figure 4-18.
4. Operation Using the Main Menu ~ ~ ~ ~ • 75% Col bars 50% Gray Gray Steps 1 Gray Steps 2 Raster Box — This function enables or disables the raster box. ~ When turned ON, the system displays a one-pixel border around the active output area. Note that the raster box includes gaps that enable you to precisely align the input video to fill the output raster. ~ When turned OFF, the output is clean, without the border.
4. Operation Using the Main Menu p~îÉ=lìíéìí=`çåÑáÖ From the Output Menu, select Save Config to save the current output configuration. A message is briefly shown, after which the system returns to the Output Menu. Savin g Output Co nfig Figure 4-20. Saving Output Configuration Message Please note the following important points regarding the output configuration file: • When you perform the Save Config function, all configuration parameters from the Output Menu are saved in non-volatile memory.
4. Operation Using the Main Menu póëíÉã=jÉåì From the Main Menu, select System to display the System Menu, which enables you to to adjust transition times, VFD Brightness, and other “system” related functions: SY STE M > T r a ns T i m e VF D Bright ness Et hernet EDID DVI I n Frmt DVI Cable Equal Temperature User Preference Dia gnostics Save Con fig 1.5 10 >> >> >> >> >> >> Figure 4-22.
4. Operation Using the Main Menu Note that transition times are specified for switching applications with Auto Acquire turned OFF. When Auto Acquire is ON, the transition time is greater, due to the additional time required to analyze the input video timing. Transition values are listed below: • • Adjustment range: 1.5 - 5.0 seconds Default: 2.0 seconds sca=_êáÖÜíåÉëë From the System Menu, select VFD Brightness to control the intensity of the front panel VFD (vacuum fluorescent display).
4. Operation Using the Main Menu • Config Network — select this function to display the Config Network Menu, which enables you to choose the specific Ethernet address you wish to change. CO N F I G N E T W OR K > Set St atic IP Set Netmask Set Gateway >> >> >> Figure 4-25. Config Network Menu ~ Select Set Static IP to display the Static IP Menu, which enables you to set a static IP address when a DHCP server is not available. The editing procedure is discussed below. ST ATIC IP > 192.168.000.
4. Operation Using the Main Menu c. When the desired digit is highlighted, press SEL to edit the value. The carat changes to the pound sign “#.” d. Use the ADJUST knob to select the desired value (0 - 9). e. Once the value is selected, press SEL to “accept” the new value. The pound sign “#” changes back to the carat “^.” f. Repeat the process from step b for all additional digits that you wish to change. g. When all editing is complete, press ESC to display the Apply Changes Menu.
4. Operation Using the Main Menu The following functions are available: • Input — selects the exact inputs that you wish to program: ALL (inputs 2 and 3), 2 (individually), or 3 (individually). • EDID Format — This line displays the system’s current EDID format, and enables you to select a new EDID format to program into non-volatile memory. As required, press SEL to scroll through the formats.
4. Operation Using the Main Menu asf=`~ÄäÉ=bèì~äáò~íáçå From the System Menu, select DVI Cable Equal to display the DVI Cable Equalizer Menu, which enables you to adjust input cable equalization parameters for both DVI inputs simultaneously, or individually for inputs 2 or 3. DV I CAB LE EQUA LIZ ER > Inpu t Equalization Set to Def aul t All 12 Figure 4-33.
4. Operation Using the Main Menu Note that the ACS-2048 measures the internal temperature for an “over-temp” condition every 5 minutes. If the system’s internal temperature exceeds 122° F (50° C), the following message appears: O VE R T EM PE RA T U RE Co ntact f actory if conditio n persist s. ESC = Continue Figure 4-35. Over Temperature Warning To clear the message and continue operations, press ESC. Note This message is a warning only, which does not prevent the operation of the ACS-2048.
4. Operation Using the Main Menu S Example: The Status Menu is currently displayed. When you press TEST PAT, the Test Patterns Menu is immediately displayed. ~ When Menu Context is OFF, menu context does not change when an Input or the TEST PAT button is pressed. aá~ÖåçëíáÅë From the System Menu, select Diagnostics to display the Diagnostics Menu: DI AGNOS TIC S > SE L = Sta rt T ests Figure 4-37.
4. Operation Using the Main Menu • If you make a change in the System Menu, and attempt to exit the menu (by pressing ESC, TEST PAT, or by selecting another input) without saving changes, the system displays the following prompt: Save System Cfg? = Yes = No Figure 4-39. Save System Configuration Prompt ~ ~ ACS-2048 • User’s Guide Select Yes (SEL) to save changes. Select No (ESC) to continue operation without saving the changes.
4. Operation Using the Main Menu pí~íìë=jÉåì From the Main Menu, select Status to display the Status Menu: IN: SDI 19 20x1080i @60 Twin 10-bit 2048x1080 p @59. 94 OUT: — Input Type — Input Format — Output Type — Output Format Figure 4-40. Status Menu (sample) The Status Menu provides information about the currently selected system input and output. The input section always reflects the selected input channel, as determined by the input buttons.
4. Operation Using the Main Menu pçÑíï~êÉ=sÉêëáçå From the Main Menu, select Software Version to display the Software Version Menu: S O F T W A R E V E R S I ON 01. 00 Figure 4-41. Software Version Menu The version shown is the current version of installed operating firmware. This number changes when you update system software. In Chapter 5, refer to the “Software Upgrade Overview” section on page 74 for software update instructions.
4. Operation Using Inputs rëáåÖ=fåéìíë This section provides background information and instructions for using inputs. The following topics are discussed: • • • Understanding Backlighting Input Selection Rules Understanding Auto Acquire råÇÉêëí~åÇáåÖ=_~ÅâäáÖÜíáåÖ The backlighting of the input buttons reflects sync detection, as follows: • Off — indicates that sync has not been detected on the input connector, and the input cannot be used on air. The input is invalid.
4. Operation Using Inputs • Input 8 is currently not implemented. If the input button is pressed, the following message appears: Invalid Selection Opt i on Card No t Inst alled Figure 4-44. Error message: Invalid Selection • Remember that the Menu Context option on the User Preference Menu affects the way that menus are displayed. Refer to the “User Preference” section on page 63 for details.
4. Operation Using Test Patterns rëáåÖ=qÉëí=m~ííÉêåë TEST PAT Pressing the TEST PAT button selects the internal test pattern as the ACS-2048’s source. There are two ways to use the button: • When TEST PAT is pressed, the button lights, and the internal test pattern is routed to the output. When you select another input, the system transitions to the new input. • When the TEST PAT button is already lit, press the TEST PAT button again to toggle back to the last selected input.
4. Operation Front Panel Lockout cêçåí=m~åÉä=içÅâçìí The ACS-2048 includes a front panel lockout mode which when enabled, locks out the front panel from all source selections, including the Test Pattern. Use the following steps to lock (and unlock) the front panel: 1. Press and hold the SEL and ESC buttons for 3 seconds. Once this button combination has been detected, the following display appears: Fro nt Panel L oc k o u t E n a b l e d Figure 4-45.
4.
RK==réÖê~ÇáåÖ=pçÑíï~êÉ få=qÜáë=`Ü~éíÉê This chapter provides detailed instructions for upgrading ACS-2048 system software.
5. Upgrading Software Software Upgrade Overview pçÑíï~êÉ=réÖê~ÇÉ=lîÉêîáÉï Firmware files for the ACS-2048 are loaded into the hardware at power-up. These files are stored in the unit’s onboard flash memory.
5. Upgrading Software Downloading Software açïåäç~ÇáåÖ=pçÑíï~êÉ Two different methods can be used to download ACS-2048 software: • • Via FTP Site Via Web Site sá~=cqm=páíÉ Barco Folsom's FTP site address is: ftp.folsom.com To download software from the FTP site: 1. Create a target folder on your PC (e.g., ACS-2048). 2. Ensure that your PC is connected to the internet. 3. There are three ways to log on to the FTP site: a.
5. Upgrading Software Ethernet Upgrade Method 4. Navigate to the “Digital Cinema” home page: http://www.barco.com/digitalcinema/ 5. Log in to the Barco Partnerzone. 6. Navigate to the “Software Updates” link, and download the latest version of code: 7. When the File Download Dialog appears, click Save. 8. When the Save As Dialog appears, navigate to the target folder and click Save. 9. Please continue with the “Ethernet Upgrade Method” section on page 76. ACS2048_##_##.tar.
5. Upgrading Software Ethernet Upgrade Method 8. When the PC establishes communications with the ACS-2048, several web pages are downloaded into the PC, and the ACS-2048 Upgrade Page appears: Figure 5-2. ACS-2048 Upgrade Page (sample) 9. Click the Firmware Upgrade link to continue the upgrade process. The Select File page appears, as shown below: Figure 5-3.
5. Upgrading Software Ethernet Upgrade Method 10. Click the Browse button, and navigate to the folder on your PC where you saved the latest version of code. 11. In the Upload Dialog, select the file: ACS2048_##_##.tar.gz ... and click Open. 12. In the Select File page, click Upload File. The Upload Status page appears, which provides status during the upload procedure: Figure 5-4. ACS-2048 Upload Status Page (sample) 13.
5. Upgrading Software Ethernet Upgrade Method qêçìÄäÉëÜççíáåÖ=bíÜÉêåÉí=`çããìåáÅ~íáçå Use the following steps to determine the IP address of the ACS-2048, and establish proper communications: 1. Power-up the ACS-2048. 2. Note the ACS-2048’s current IP address: 3. a. From the Main Menu, select System to display the System Menu. b. From the System Menu, select Ethernet to display the Ethernet Menu. c.
5.
^K==péÉÅáÑáÅ~íáçåë få=qÜáë=^ééÉåÇáñ This appendix provides detailed technical specifications for the ACS-2048.
^K==péÉÅáÑáÅ~íáçåë Input Specifications fåéìí=péÉÅáÑáÅ~íáçåë= The table below lists ACS-2048 input specifications. Table A-1. ACS-2048 Input Specifications Parameter Input 1 Detail Specification Connector BNC Format SD-SDI per SMPTE 259M-C (NTSC/PAL resolution) HD-SDI per SMPTE 292M (HDTV) Input 2 Input 3 Input 4 Connector DVI-I, per DDWG 1.0 Format 8-bit DVI, RGBHV data via analog pins HDCP hardware support HDCP version 1.
^K==péÉÅáÑáÅ~íáçåë Output Specifications Table A-1. ACS-2048 Input Specifications (Continued) Parameter Input 6 Input 7 Input 8 Detail Specification Connector BNC Format NTSC or PAL video (CVBS) Connector 4-pin mini-DIN Format Encoded NTSC or PAL Y/C video Not currently implemented lìíéìí=péÉÅáÑáÅ~íáçåë The table below lists ACS-2048 output specifications: Table A-2.
^K==péÉÅáÑáÅ~íáçåë Physical and Electrical Specifications mÜóëáÅ~ä=~åÇ=bäÉÅíêáÅ~ä=péÉÅáÑáÅ~íáçåë= The table below lists ACS-2048 physical and electrical specifications. Table A-3. ACS-2048 Physical and Electrical Specifications Parameter Power Mechanical Detail Specification Connector Standard IEC, integral on/off switch Power 100-240 VAC, 50-60 Hz Chassis H: 3.50 inches (8.89 cm) W: 17.00 inches (43.18 cm) W: 19.00 inches (48.26 cm) with rackmount wings D: 10.00 inches (25.
^K==péÉÅáÑáÅ~íáçåë Communications Specifications `çããìåáÅ~íáçåë=péÉÅáÑáÅ~íáçåë= The table below lists ACS-2048 communications specifications. Table A-4. ACS-2048 Communications Specifications Parameter Communications Detail Ethernet Specification RJ-45, 10/100 Mbps ^ÖÉåÅó=péÉÅáÑáÅ~íáçåë= The table below lists ACS-2048 agency specifications. Table A-5.
^K==péÉÅáÑáÅ~íáçåë Pinouts máåçìíë= The following topics are discussed in this section: • • • • Analog 15-pin D Connector DVI-I Connector Pinouts Ethernet Connector Mini-DIN Connector ^å~äçÖ=NRJéáå=a=`çååÉÅíçê The figure below illustrates the analog 15-pin D connector: 5 1 10 6 15 11 Figure A-1. Analog 15-pin D connector, chassis view The table below lists Analog 15-pin D connector pinouts. Table A-6.
^K==péÉÅáÑáÅ~íáçåë Pinouts asfJf=`çååÉÅíçê=máåçìíë The figure below illustrates the DVI-I connector: 1 8 C1 C2 9 C5 17 24 C3 C4 Figure A-2. DVI-I connector The table below lists DVI-I connector pinouts. Please note: • • T.M.D.S = Transition Minimized Differential Signal DDC = Display Data Channel Table A-7. DVI-I Connector Pinouts Pin Signal Pin Signal 1 T.M.D.S. Data 2- 13 T.M.D.S. Data 3+ 2 T.M.D.S. Data 2+ 14 +5V Power 3 T.M.D.S. Data 2/4 Shield 15 ground (for +5V) 4 T.M.D.S.
^K==péÉÅáÑáÅ~íáçåë Pinouts bíÜÉêåÉí=`çååÉÅíçê The figure below illustrates the Ethernet connector: 1 8 Figure A-3. Ethernet connector The table below lists Ethernet connector pinouts. Table A-8. Ethernet Connector Pinouts Pin Signal Wire Color 1 TX Data + White / Orange 2 TX Data - Orange 3 RX Data + White / Green 4 Blue 5 White / Blue 6 RX Data - Green 7 White / Brown 8 Brown jáåáJafk=`çååÉÅíçê The figure below illustrates the 4 pin Mini-DIN connector. 3 4 1 2 Figure A-4.
^K==péÉÅáÑáÅ~íáçåë Input Format Table fåéìí=cçêã~í=q~ÄäÉ The table below lists the available input formats for the ACS-2048. Each entry uses the following convention: Format @Fv (Hz). Table A-10. ACS-2048 Input Formats Format Aspect Ratio Color Space NTSC (480i) 1.33333 SMPTE, RGB 720x480p 1.33333 SMPTE, RGB PAL (576i) 1.33333 SMPTE, RGB 720x575p 1.33333 SMPTE, RGB 640x480 @59.94 1.33333 RGB 640x480 @60 1.33333 RGB 640x480 @72 1.33333 RGB 640x480 @75 1.33333 RGB 640x480 @85 1.
^K==péÉÅáÑáÅ~íáçåë Input Format Table Table A-10. ACS-2048 Input Formats (Continued) Format 90 Aspect Ratio Color Space 1280x768 @48 1.66667 RGB 1280x768 @50 1.66667 RGB 1280x768 @59.94 1.66667 RGB 1280x768 @75 1.66667 RGB 1280x960 @50 1.33333 RGB 1280x960 @59.94 1.33333 RGB 1280x960 @60 1.33333 RGB 1280x960 @85 1.33333 RGB 1280x1024 @47.95 1.25 RGB 1280x1024 @48 1.25 RGB 1280x1024 @50 1.25 RGB 1280x1024 @59.94 1.25 RGB 1280x1024 @60 1.25 RGB 1280x1024 @71.93 1.
^K==péÉÅáÑáÅ~íáçåë Input Format Table Table A-10. ACS-2048 Input Formats (Continued) Format Aspect Ratio Color Space 1400x1050 @75 1.33333 RGB 1536x768 @50 2 RGB 1536x768 @59.94 2 RGB 1680x1050 @60 1.6 RGB 1600x1200 @47.95 1.33333 RGB 1600x1200 @48 1.33333 RGB 1600x1200 @50 1.33333 RGB 1600x1200 @59.94 1.33333 RGB 1600x1200 @60 1.33333 RGB 1280x720p @48 1.77778 SMPTE, RGB 1280x720p @50 1.77778 SMPTE, RGB 1280x720p @59.94 1.77778 SMPTE, RGB 1280x720p @60 1.
^K==péÉÅáÑáÅ~íáçåë Input Format Table Table A-10. ACS-2048 Input Formats (Continued) Format 92 Aspect Ratio Color Space 2048x1080p @60 1.77778 RGB 1920x1200p @60 1.77778 RGB 1920 x 1200 II @60 1.77778 RGB 1920 x 1080 II @60 1.77778 RGB, SMPTE 2048 x 1080 II @60 1.7778 RGB Apple 1200p @60 1.6 RGB 875p 1.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä få=qÜáë=^ééÉåÇáñ This appendix provides information regarding remote control protocol. The following topics are discussed: • • • • • Communicating with ACS-2048 Command Protocol Error Codes ACS-2048 Command List Remote Commands `çããìåáÅ~íáåÖ=ïáíÜ=^`pJOMQU Use the following steps to communicate with the ACS-2048 via Telnet: 1. Connect the ACS-2048’s Ethernet port to an Ethernet switch, and connect the switch to your PC or laptop. 2.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Command Protocol `çãã~åÇ=mêçíçÅçä The ACS-2048’s command protocol is compatible with GNU getopt parsing. Every parameter of the command has an option character associated with it. A carriage return (ASCII 13) terminates the command. Note The order of the option characters in the command does not matter. S Command example: ITYPE -i 2 -t 1 Or ITYPE -t 1 -i 2 `çãã~åÇ=oÉëéçåëÉë A command response is sent after each command is processed.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Command Protocol • Parameters: -i(input): Input number, 1-8 -b(bright): 75.0%-125.0% • • Query Format: IBRT i(input) -? Query Response: IBRT i(input) b(bright) --min 75 --max 125 IBRT -e 0 Current Setting Query — The current setting query option (-?) returns the command with each of the current parameter settings. Commands with minimum and maximum settings for the parameter will have these “min” and “max” values returned with option flags --min and --max.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Error Codes bêêçê=`çÇÉë This section provides ACS-2048 error codes: bêêçê=`çÇÉëW==dÉåÉê~ä=c~áäìêÉë The table below lists general failure codes: Table B-1. ACS-2048 General Error Codes Code Description -9999 Generic fail -9998 Operation is not applicable in current state -9997 UI Related... Did not get response from device -9996 UI Related...
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä ACS-2048 Command List ^`pJOMQU=`çãã~åÇ=iáëí The table below lists ACS-2048 remote commands. Table B-1.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands Table B-1. ACS-2048 Remote Commands (Continued) Command Description Page SAVE System Save 105 LOCKOUT Controls the lockout mode of the front panel 105 ISTAT Query only command for the input status type and format. 105 OSTAT Query only command for the output status type and format 105 oÉãçíÉ=`çãã~åÇë This section lists ACS-2048 remote commands.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands • • • bj^` • • • • • • Query Format: GATEWAY -? Query Response: GATEWAY -a (active addr) -s (static addr) Query Params: -a (active addr): Active gateway active address Description: Get MAC Address Command Format: N/A Command Params: N/A Query Format: EMAC -? Query Response: EMAC -a (addr) Response Params: -a (addr): MAC address formatted xx.xx.xx.xx.xx.xx ^rql^`n • Description: Auto Input Acquisition Mode.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands • Parameters: -i (input): 1 - 8 -p (pan): In pixels • • Query Format: IHPAN -i (input) -? Query Response: IHPAN -i (input) -p (pan) --min (active min) -- max (active max) fs`olm= • Description: Input Vertical Crop • Command Format: IVCROP -i (input) • Parameters: -h (height) -i(input): 1 - 8 -h(height): In lines • • Query Format: IVCROP -i(input) -? Query Response: IVCROP -i(input) -h(height) --min (pos min) -- max (pos max) fsm^k= • Description: Input V
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands _ihsfa • Description: Puts black into the scaler selected. • Command Format: BLKVID -s (scaler) -m (mode) • Parameters: -s (scaler): 1 - 2 -m (mode): 0 - off, 1 - on • • lobp= • • • Query Format: N/A Query Response: N/A Description: Output Resolution Command Format: ORES -o (output) [-f (format) | -n (index)] Parameters: -o (output): 1 - DVI -f (format): format string, i.e. "2048x1080 @60" (Default: 2048x1080 @ 59.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands -t (type): • 1 - H Ramp • 2 - V Ramp • 3 - 100% Col Bars • 4 - 16x16 Grid • 5 - 32x32 Grid • 6 - Burst • 7 - 75% Col bars • 8 - 50% Gray • 9 - Gray Steps 1 • 10 - Gray Steps 2 • • • • Query Format: OTPT -o (output) -? Query Response: OTPT -o (output) - t (type) --min 1 -- max 10 List Format: OTPT -o (output) --list List Response: 1: "H Ramp" 2: " V Ramp" 3: "100% Col Bars" 4: "16x16 Grid" 5: "32x32 Grid" 6: "Burst" 7: "75% Col bars" 8: "50% Gray" 9: "Gray Steps
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands • • • • Query Format: OMODE -o (output) -? Query Response: OMODE -o (output) -w(width) --min 0 -- max 2 List Format: OMODE -o (output) --list List Response: 0: "8 bits" 1: "10 bits" 2: "12 bits" ldj= • • • Description: Set Output Gamma Command Format: OGM -o (output) -g (gamma) Parameters: -o output: 1 - DVI -g gamma: 1.0 to 3.0; +0.1 increment (Default: 1.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands ^rqlp^sb= • Description: Auto Input Settings Save • Command Format: AUTOSAVE -m (mode) • Parameters: -m (mode): 0 - off, 1 - on (default: off) • Query Format: AUTOSAVE -? • Query Response: AUTOSAVE -m (mode) --min 0 -- max 1 pbijlab= • Description: Sets whether input selection of inputs w/o valid syncs will be made.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands • • • p^sb= • • • • • Parameters: N/A Query Format: N/A Query Response: N/A Description: System Save Command Format: SAVE Parameters: N/A Query Format: N/A Query Response: N/A il`hlrq • Description: Controls the lockout mode of the front panel. When enabled, the keys and menu will be deactivated.
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä Remote Commands 106 ACS-2048 • User’s Guide
`K==`çåí~Åí=fåÑçêã~íáçå få=qÜáë=^ééÉåÇáñ The following topics are discussed in this Appendix: • • • Warranty Return Material Authorization (RMA) Contact Information t~êê~åíó All video products are designed and tested to the highest quality standards and are backed by a full 3-year parts and labor warranty. Warranties are effective upon delivery date to customer and are non-transferable. Barco warranties are only valid to the original purchaser/owner.
`K==`çåí~Åí=fåÑçêã~íáçå Contact Information `çåí~Åí=fåÑçêã~íáçå Barco Media and Entertainment 11101 Trade Center Drive Rancho Cordova, California 95670 USA • • • Phone: (916) 859-2500 Fax: (916) 859-2515 Website: www.barco.com Sales Contact Information • • • Direct: (916) 859-2505 Toll Free: (888) 414-7226 E-mail: folsomsales@barco.com Barco N.V. Noordlaan 5 8520 Kuurne BELGIUM • • • Phone: +32 56.36.82.11 Fax: +32 56.35.16.51 Website: www.barco.
fåÇÉñ kìãÉêáÅë 10/100BaseT . . . . . . . . . . . . . . . . . . . . . . . . . .23 1-1 Sampling . . . . . . . . . . . . . . . . . . . . . . . . . .49 3-2 film pulldown . . . . . . . . . . . . . . . . . . . . . . .50 ^ AC connector . . . . . . . . . . . . . . . . . . . . . . . . .24 power and voltage selection . . . . . . . . . . .28 power cords . . . . . . . . . . . . . . . . . . . . . . .28 power installation . . . . . . . . . . . . . . . . . . .27 Acrobat usage . . . . . . . . . . . . . . . . . . . . . .
Index _ Backlighting, understanding . . . . . . . . . . . . . . .68 Barco contact information . . . . . . . . . . . . . . . . .108 sales contact information . . . . . . . . . . . .108 technical support information . . . . . . .3, 108 warranty . . . . . . . . . . . . . . . . . . . . . . . . .107 Best guess format . . . . . . . . . . . . . . . . . . . . . .44 Blinking button . . . . . . . . . . . . . . . . . . . . . . . . .21 BLKVID (command) . . . . . . . . . . . . . . . . . . . .101 Block diagram . . . . .
Index CONTEXT (command) . . . . . . . . . . . . . . . . .104 Context, menu . . . . . . . . . . . . . . . . . . . . . . . . .63 Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Control overview . . . . . . . . . . . . . . . . . . . . . . .32 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . .12 menu system . . . . . . . . . . . . . . . . . . . . . .36 Copy protection . . . . . . . . . . . . . . . . . . . . . . . .14 Copyright . . . . . . . . . . . . . . . . . . . . . . .
Index e H active . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 crop . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 position . . . . . . . . . . . . . . . . . . . . . . . . . . .49 total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . .25 orientation . . . . . . . . . . . . . . . . . . . . . . . . .17 requirements, upgrading software .
Index diagnostics . . . . . . . . . . . . . . . . . . . . . . . .64 display . . . . . . . . . . . . . . . . . . . . . . . . . . .20 DVI cable equalizer . . . . . . . . . . . . . . . . .62 EDID DVI input format . . . . . . . . . . . . . . .60 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . .58 factory reset . . . . . . . . . . . . . . . . . . . . . . .67 gateway . . . . . . . . . . . . . . . . . . . . . . . . . .59 hue/saturation color balance . . . . . . . . . .48 image adjust . . . . . . . . .
Index n Query options . . . . . . . . . . . . . . . . . . . . . . . . .94 Quick function reference . . . . . . . . . . . . . . . . . . .38 setup and operations . . . . . . . . . . . . . . . .33 o Rack mount installation . . . . . . . . . . . . . . . . . .27 Raster Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Rear panel connectors . . . . . . . . . . . . . . . . . . .23 Reference, quick function table . . . . . . . . .
Index using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 TEMP (command) . . . . . . . . . . . . . . . . . . . . .104 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . .62 over-temp condition . . . . . . . . . . . . . . . . .63 Terms, equipment marking . . . . . . . . . . . . . . . .5 TEST PAT . . . . . . . . . . . . . . . . . . . . . . . . .19, 70 how to use . . . . . . . . . . . . . . . . . . . . . . . .22 Test pattern menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index 116 ACS-2048 • User’s Guide
