Brochure

ManualsBrandsBarber Colman ManualsDampersProportional Actuator w/ 10 ft. Plenum Rated Cable (24V)

151

152

153

154

155

156

157

158

159

160

Table Of Contents

F-27855-10156

VB-2000 Series Ball Valves

with SmartX Actuators

schneider-electric.com | 3

Selection Guide

Document Number: F-27086-14

Ball Valve Assembly Selection Procedure

When selecting a ball valve assembly, you must determine the applicable codes for the control signal type, valve body conﬁgura-

tion, end connection, port size, and actuator. Select a ball valve assembly part number as follows:

1. Control Signal Type, Valve Body Configuration, and End Connection

Refer to “Ball Valve Assemblies Using SmartX 5xx Actuators” on page 157 or “Ball Valve Assemblies Using SmartX 8xx

Actuators” on page 158, and then select the appropriate codes for these part number fields.

2. Valve Size (Flow Coefficient)

If the required flow coefficient (Cv) has not yet been determined, do so as follows:

a. Refer to the “Sizing and Selection” on page 171 to calculate the required Cv.

b. Select the nearest available Cv and corresponding valve body port code from “2-Way Ball Valve Assemblies with SmartX

Actuators” on page 159 or “3-Way Ball Valve Assemblies with SmartX Actuators” on page 160.

3. Actuator

Select the appropriate actuator and code, according to “Ball Valve Assemblies Using SmartX 5xx Actuators” on page 157 or

“Ball Valve Assemblies Using SmartX 8xx Actuators” on page 158, based on the control signal type, required valve normal

position, and voltage requirements. For detailed actuator information, refer to the applicable actuator specifications.

NOTE: Ball Valve Assemblies with SmartX Actuators use the basic actuators. However, if an actuator with auxiliary switch(es) is required, you

may field-assemble a ball valve assembly using a ball valve body/linkage assembly (VB-2x13-500-9-xx). For information on switch-

equipped actuators, refer to “Assemblies with Mx40-704x SR SmartX Actuators” on page 167 and “Assemblies with

Mx4D-703x/803x SR SmartX Actuators” on page 168, “Assemblies with MF/Ms41-6043/83 NSR SmartX Actuators” on page 166.

4. Close-off Pressure

Conﬁrm in Table-4, Table-5, Table-6, and Table-7 that the selected actuator and valve body combination provides sufﬁcient

close-off pressure. If no close-off pressure is shown, the valve body/actuator combination is not valid.

5. Available Space

If available space is a consideration, check the appropriate dimensional ﬁgure (Figure 1 through Figure 8) and its accompa-

nying table for any potential ﬁt problems.

MA40-704x, MA4x-707x, MA4x-715x General Instructions ...... F-26642

MF4x-7xx3, MF4x-7xx3-50x General Instructions .............. F-26644

MS4x-7xx3, MS4x-7xx3-50x General Instructions ............. F-26645

MF41-6043, MF41-6083 General Instructions ................. F-27213

MA4D-xxxx, MF4D-xxxx, MS4D-xxxx General Instructions. . . . . . . F-27170

MS41-6043, MS41-6083 General Instructions

................ F-27214

Mx40-704x Mounting and Wiring Instruction .................. F-27003

Mx41-6043 Data Sheet .................................. F-26737

Mx41-6043 Submittal Sheet .............................. F-27216

Vx-2xx3-5xx-9-xx, VB-2xx3-500-9-xx ....................... F-27087

EN205 Water and Steam Systems. . . . . . . . . . . . . . . . . . . . . . . . . . F-26080

Applicable Literature