Product Overview

ManualsBrandsBarber Colman ManualsDampers120V Actuator Drive with 1/15 VDC Input

TAC

1354 Clifford Avenue

P. O. Box 2940

Loves Park, IL 61132-2940

www.tac.com

Application

The CP-8301-xxx Series electronic actuator drive is

designed to process a variable 1 to 15 Vdc signal from

a controller to provide proportional control of an electric

gear train actuator.

Features

• Mounts directly onto TAC proportional, electric, gear

train actuators.

• Fixed 1 to 15 Vdc operating range.

• 24, 120, and 240 Vac models available.

• Color-coded pigtail leads.

Applicable Literature

• TAC Environmental Controls Cross-Reference

Guide, F-23638

• TAC Environmental Controls Reference Manual,

F-21683

• TAC Environmental Controls Application Manual,

F-21335

• TAC Pneumatic Products Catalog, F-27383

• MP-3xx Series, MP-4xx Series, MP-2xxx Series,

and MP-4xxx Series Reversible and Proportional

Electric Actuators General Instructions, F-15479

CP-8301-xxx Series

1 to 15 Vdc Input Electronic Actuator Drive

General Instructions

Summary of content (8 pages)

PAGE 1
CP-8301-xxx Series TAC 1354 Clifford Avenue P. O. Box 2940 Loves Park, IL 61132-2940 www.tac.com 1 to 15 Vdc Input Electronic Actuator Drive General Instructions Application The CP-8301-xxx Series electronic actuator drive is designed to process a variable 1 to 15 Vdc signal from a controller to provide proportional control of an electric gear train actuator. Features • Mounts directly onto TAC proportional, electric, gear train actuators. • Fixed 1 to 15 Vdc operating range.
PAGE 2
SPECIFICATIONS Inputs Control Signal: Range, 1 to 15 Vdc, nonadjustable. Span, Refer to Table-1. Start Point, Refer to Table-1. Power Requirements: Refer to Table-1. Power Supplies: Refer to Table-1. Outputs Connections: Color-coded pigtail leads. Mounting: Directly to an actuator. The upright position is preferred, but other positions are acceptable. Case: Bakelite. Environment Ambient Temperature Limits: Shipping & Storage, -40 to 160° F (-40 to 71° C). Operating, -40 to 136° F (-40 to 58° C).
PAGE 3
ACCESSORIES None TOOLS Appropriate screwdriver TOOL-201 Calibration kit for TAC System 8000TM TYPICAL APPLICATIONS (wiring diagrams) Refer to Figure-1 for a service application wiring diagram showing the connections between a CP-8301-xxx series drive and an MP-3xx, MP-4xx or MP-21xx series actuator.
PAGE 4
Warning: • Electrical shock hazard! Disconnect power before installation to prevent electrical shock or equipment damage. • Make all connections in accordance with the electrical wiring diagram and in accordance with national and local electrical codes. Use copper conductors that are suitable for 75°C. Caution: • Do not exceed the ratings of the device(s). • Static charges produce voltages high enough to damage the electronic components.
PAGE 5
Power Wiring Compartment 1 L1 (H) L2 (G) Drive 3 L1(H) L2 (G) 1 5 6 x 8 Barrier 7 2 4 3 2 To Controller Location of Start Point Adjustment Potentiometer Low Voltage Wiring Compartment 1 Actuator 1 Top view. 2 Remove green wire from terminal X. 3 Right-side mounting is shown. Figure-3 Actuator/Drive Wiring and Mounting Arrangement. WIRING Power Wiring All the power to the drive is supplied by the electric actuator onto which the drive is mounted. Refer to Figure-4.
PAGE 6
Red Yellow / Black Blue / Black Red / Black Brown 4 3 5 6 Actuator 2 Yellow Yellow (OP1) 3 Blue 7 8 Brown / White Brown / Black 3 H Black 1 4 6 X Red (+20) G AC Supply 5 1 CP-8301-024 can be used with the following electric actuators: MP-361, 371, 381, 382, 2113-500 and 9713. CP-8301-120 can be used with the following electric actuators: MP-465, 475, 483, 485, 486, 495, and 2150-500. 2 CP-8301-240 can be used with 240 Vac electric actuators. (Available as a standard option.
PAGE 7
Go, No Go Test 1. Disconnect the field wiring from the red, yellow, and blue leads of the drive. 2. Apply power to the actuator. 3. Short the yellow and red leads of the drive. The actuator should rotate CW to its limit, unless it is rewired to rotate CCW on an increase in input signal. Disconnect the short between the yellow and red leads. 4. Short the yellow and blue leads of the drive. The actuator should rotate CCW to its limit, unless it is rewired to rotate CW on an increase in input signal.
PAGE 8
MAINTENANCE The drive requires no maintenance. Regular maintenance of the total system is recommended to assure sustained, optimum performance. FIELD REPAIR None. Replace an inoperative drive with a functional unit. DIMENSIONAL DATA 3-1/4" (83mm) 2-1/2" (64mm) 4" (102mm) 1-7/8" (48mm) 1" (25mm) 1/2" Conduit Thread 4" (102mm) Figure-5 Mounting Dimensions of CP-8301-xxx Series Electronic Actuator Drive.