Owner`s manual

CARE AND MAINTENANCE
D
i
a
g
r
a
m
1
1
CLEANING THE FILTER ELEMENT
Clean the filter element at the end of each cycle.
• Ensurethatthepowersupplycablehasbeendisconnected
from the electrical outlet or that the floating cable has been
disconnected from the power supply.
• Removethecleanerfromthewaterandlayitupsidedown
to access the filter frame plate located on the bottom of the
cleaner. Diagram 9.
• Undothe4clipsthatholdtheplateinplace.Removeit,while
holding it upside down so that the dirt remains in the filter
element. Diagrams 9 & 10.
• Releasethetwo(2)plasticretainerclipstoremovethefilter
element. Diagram 11.
• Carefullyremovetheelasticfromthebaseofthefilterandthen
remove it from the filter frame plate. Diagram 12.
• Emptythefilterelementandcleanitwithrunningwaterorif
necessary with slightly soapy water. If you use soap, rinse it
thoroughly while turning it over. You can also machine wash it,
following the instructions given on the label inside the
filter element.
• Rinsethefilterframeplateandremoveanydirtcaughtunder
the flaps.
• Replacethefilterelementandensuretheelasticfitssnugly
around the filter frame. Diagram 12. The Zodiac Pool Systems,
Inc. label should be located in the corner, alongside a rod.
• Positiontheplasticretainerclipsatthetopoftherods.
• Replacethefilterframeplateandsnapitintoplace.
D
i
a
g
r
a
m
1
2
D
i
a
g
r
a
m
1
0
Filter Frame
Plate
Filter Element
Filter Frame
Retainer Clips
D
i
a
g
r
a
m
9
Clips
Metallic Rods
(Inside)
CARE AND MAINTENANCE
CLEANING AND STORAGE OF THE CLEANER
• Thecleanermustbecleanedregularlywithcleanorslightlysoapy
water. Rinse thoroughly in clean water.
• Donotleaveyourcleanertodryinthesunbythepool.
• Thecleanermustbestoredonthecaddysothatthebrushes
do not deteriorate and the cleaner dries quickly.
CHANGING THE bRUSHES
We recommend that you change the brushes every two (2) years or
once they have become worn.
Brush Removal:
• Turnthecleanerupsidedown.
• Separatetheedgesofthebrushandundothetabs,thenremovethe
worn brushes. Diagram 13.
Brush Installation:
• Positionthenewbrushesontherollerwiththespikesfacing
outward. Diagram 14.
• Threadeachtabintotheslotprovidedandgentlyfeeditthrough
so that the heel comes out at the other side of the slot.
• Useapairofscissorstocutthetabs3/4inchfromtheheelsothat
they are no higher than the spikes.
WEIGHT ADJUSTMENTS
Weight adjustments can improve the cleaning efficiency of your
cleaner and adapt its pattern to your pool.
If cleaner does not cover the entire pool, move the weight from the
#5 post, closest to the floating cable side of the cleaner, to the #3
post and recheck coverage.
To adjust coverage further, move the weight to the #1 post. The #2 and
#4 posts can be used for fine tuning the cleaner balance. Diagram 15.
If cleaner is too buoyant, sucking air when at the water line, add the
extra weight (two stainless steel plates) included in the manual
bag to the #3 post. Diagram 15.
If cleaner does not climb walls to water line, remove all weights.
To access the motor block:
•Unplugthepowersupplyandremovethecleanerfromthepool.
•Withrobotupsidedown,removefilterelementframeplate.
•Loosenthescrewssecuringthemotorblockprotection
grid and remove it.
•Makeweightadjustment.
•Replacemotorblockprotectiongridandfilterframeplate.
D
i
a
g
r
a
m
1
3
D
i
a
g
r
a
m
1
4
Slot
Spikes
Tab
Roller
Front
Bumper
Weight
Motor Block
1 2 543
D
i
a
g
r
a
m
1
5
8
9