Owner`s manual

ASSEMBLY AND INITIAL USAGE
6
D
i
a
g
r
a
m
5
WARNING
Failure to heed the following warnings can result
in permanent injury, electrocution or drowning.
!
PREVENT ELECTRICAL SHOCK
• Keepthepowersupplyatleastfive(5)feetfromtheedgeofthepool(3m(10ft.)
in Canada per CEC requirements). Never submerge power supply.
•Youshouldonlyconnectthepowersupplytoareceptacleprotectedbyaground
fault circuit interrupter (GFCI). Contact a certified electrician if you cannot verify
that the receptacle is protected by a GFCI.
• Donotuseanextensioncordtoconnectthepowersupply.
• DonotallowanyonetoswimwhiletheS3Roboticcleanerisinthepool.
ELECTRICAL CONNECTION
•Foryoursafetyandtoobtainthebestpossibleperformance
from your S3 Robotic, connect the cleaner’s floating cable to the
power supply and thread connector until it is snug—
do not over tighten. Diagram 4.
IMPORTANT:
•S3Roboticpowersupplyisequippedwithanautomaticshutoff
feature to prevent over heating if operated in direct sunlight
for an extended period of time.
•S3Roboticpowersupplyiswater-resistant,notwaterproof.
Therefore, never submerge the power supply.
SUbMERGING THE CLEANER
•Submergethecleanerinthepoolandremoveanyairtrapped
inside by turning it over if necessary. Diagram 5.
•Ensuretheunitsinkstothebottomofthepool.
•Spreadoutthefloatingcableoverthepool,ensuringthereare
no knots or coils in the cable.
D
i
a
g
r
a
m
4
Power
Supply
Floating
Cable
Connector
INITIAL USAGE
Select either Perfect or Turbo cleaning cycle on the power supply:
The Perfect Cycle
• Completedin3hours
• Cleanswallsandfloors
• Intensiveandcompletecleaning
The Turbo Cycle
• Completedin1.5hours
• Spendsmoretimecleaningfloor
• Maximumcoverageinminimaltime
• TostartyourS3Roboticcleaner,pressthebuttonforthedesired
cycle (Perfect or Turbo). Diagram 6. The cleaner starts up after
just a few seconds and the indicator light for the cycle selected
illuminates.
• If you wish to stop the cleaner or change cycles during a cycle, press
the OFF button. Diagram 7. To start a new cycle, press the button for
the desired cycle.
• Attheendofthecyclethecleanerstopsandthelightremainsonto
indicate the cycle it last completed.
• S3Roboticincludesasafetyfeaturethatautomaticallystopsthe
cleaner after 20 seconds, when it is powered on, but not submerged
in water. For pools equipped with a beach area, this safety feature
allows the cleaner to drive in reverse, and back into the pool when
the propeller is out of the water.
To turn the S3 Robotic off, press the OFF button. Diagram 7.
• Disconnectthepowersupplycablefromtheelectricaloutlet.
• Disconnectthecablefromthepowersupply.
• Attheendofeachcycle,coilthecablestartingatthecleanerand
go toward the connection point at power supply. Remove coils or
twists along the way.
IMPORTANT:
• Waitapproximately15minutesafterthecycleiscompletedbeforeremoving
the cleaner from the water. This allows the motor to cool, and will prevent
damage to the cleaner.
• RemoveS3Roboticfromthepoolafterthecleaningcycleis
completed and store on the caddy.
• NeverliftS3Roboticoutofthepoolbythefloatingcable.Always
use the handle to remove S3 Robotic from the pool. Diagram 8.
• RemoveS3Roboticfrompoolwhensuperchlorinating.
RECOMMENDATIONS
•UseyourS3Roboticcleanerasoftenasneededtokeep
your pool clean.
•Cleanfilterelementaftereachcleaningcycle.
•Do not leave your cleaner in the pool on a permanent basis.
D
i
a
g
r
a
m
7
D
i
a
g
r
a
m
8
Handle
ASSEMBLY AND INITIAL USAGE
D
i
a
g
r
a
m
6
7