BT49QT-12 Rebel – User Manual, Service Schedule & History
Introduction Welcome to your new BAOTIAN BT49QT-12 (Rebel), which has been developed by BAOTIAN MOTORCYCLE INDUSTRIAL CO. LTD. We hope you enjoy your new Baotian BT49QT-12 (Rebel). This owner’s handbook contains information necessary: • to enable you to get to know your Baotian BT49QT-12 (Rebel), to use it to the best advantage and to benefit from all the latest developments which it incorporates.
CONTENTS Guidance............................................................................................................................................................1 Position of parts .................................................................................................................................................3 Controlling parts.................................................................................................................................................
Guidance Please keep safety in mind and observe the regulations of transportation while enjoying your ride. Pay attention to the following rules: 1. Pre-riding inspection Please read the details in the relevant chapter for your safety. IMPORTANT It is dangerous to drive on wet roads. Do not make any abrupt turning while accelerating and keep a safe distance from other vehicles on the road. 2. Helmet Do wear a helmet at all times while riding the motorcycle. 3.
. Positions of the numbers When your motorcycle needs to be inspected, repaired or undertake any service, these numbers will assist your Baotian Dealer when servicing your motorcycle. Please note down your numbers here: The frame number: ................................................ The engine number: .............................................
Position of parts 1 2 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 19 20 21 22 23 24 BAO TIAN 1. brake disc 5. disk brake assy. 9. side stand 13. rear carrier 17. rear reflector 21. right switches assy. 2. front shock absorber 6. rear-view mirrors 10. main stand 14. rear turning light 18. rear brake lever 22. front brake lever 3 3. side reflector 7. front turning light 11. starting pedal 15. air cleaner 19. left switches assy. 23. taillight 4. head light 8. helmet hook 12. rear shock absorber 16.
1. Rear brake lever A. Horn button B. Turning signal switch Hold it tight and the rear brake works Left turning light ➯ ➯ right turning light C. Switch for high/low beam lights 3. Meters and indicating lights A B C D E F 2. Switches on the left handle A. Indicates the speed in Km/h and Mph B. Indicates total distance the motorcycle has run C. Left turning light indicator D. High beam indicator E. Right turning light indicator F.
4. Front brake lever 6. Ignition switch Press it tightly and the front brake works. 5. Switches on the right ON OFF Engine can be started and all the lights can be operated. The key cannot be taken out. The whole circuit is cut. Engine and lights cannot be operated and the key can be taken out. LOCK Turn the steering handle fully to the left, slightly press the key and turn it to the position lock . Then the key can be taken out. A. Head light switch B.
Fuel and engine oil Fuel tank A. Petrol Usage of the fuel tank lock: Ensure unleaded petrol is used at all times.7 1. Turn the little cap on the fuel cap clockwise. Insert the key and turn the key clockwise and take out the fuel cap. B. Engine oil 2. Align the lock tongue on fuel cap with the notch on fuel tank, press the fuel cap and lock it. SAE-15w/40 SF 20w/40-20w/50 15w/40-15w/50 10w/30 10w/40 -10 Starting lever T 20 0 20 10 40 60 30 80 Starting lever is for kick starting the engine.
Pre-riding inspection Please check the following parts before you drive. No. Items Inspection content 2 Brake system 1.Travel of the front brake and the rear brake. 2. No damage to the cable 2. Flexible function 1 Steering handle bar 1.Flexibility. 2. No gap or loose appearance 3 Tyres 1. Correct pressure. 2.
Engine starting 3. Engine Starting 1. Please check the volume of engine oil and fuel before starting. The main stand should be stood up while starting the engine. Grip the brake lever and press the starter button and then the engine will start. 2. Turn the ignition switch to the “ON” position.
Warning: Warning: ◆ 5 seconds is the maximum limit for each starting and 10 seconds is the minimum interval. ◆ After the engine has started, the kick start pedal should be taken back to its original position. Otherwise, it will affect the driver’s safety. ◆ Stop pressing the starting button immediately after the engine starts. ◆ Don’t start the engine in enclosed spaces, as this can create Carbon Monoxide which can cause loss of life.
3. Air cleaner 1. Battery • 12V/4Ah battery • Place the ignition switch to OFF position before battery replacement. • • • When the voltage is less than 11.5V, please use kicking start in stead of electric starting. Electrode identification: “+”-red line, “-“-black line. Replace the battery every 4 years. A: Remove 6 tightening screws of air cleaner cover. Remove air cleaner cover. 2. Carburetor and idle speed adjustment • • B: Take out the sponge core.
4. Spark plug • Clean the carbon deposit on the spark plug with a piece of hard wire or steel needle. • Use A7RC when replacement is needed. • 6. Engine oil Replace the engine oil with engine warmed up. Adjust the gap to 0.6-0.7mm with a feeler gauge. Remove the oil dipstick. Remove the oil plug for displacement to drain the used oil. 5. Fuel Reinstall the oil plug for displacement, paying attention to be tightened . Always refill with unleaded petrol. Refill 0.8 L recommended fresh engine oil.
7. Brake system _ Normal free travel of the brake lever is about 2-5mm. ◆ FREE TRAVEL means the distance between the positions from free status to the beginning performance of the brake. ◆ Pay attention to the sensitivity of the brake. 1. The front brake (disk brake) Disk brake ◆Grip the brake lever and check the wear and tear indicator. If the indicator nearly touched the brake disc, please ask your Baotian Dealer to change the brake pads. 2.
8. Tyres Brake fluid level • • It has been filled with the special brake fluid before the motorcycle leaves the factory. Fluid should only ever be replace or filled with DOT4 brake fluid. Never replace or mix other fluids, otherwise it will damage the brake system. Insufficient tyre pressure increases wear to them and affects the riding stability. Please check the tyre pressure and tread depth when carrying out regular maintenance.
How to change gear oil 9. Starter motor Check the fastening bolts and the contact brushes, and replace them if necessary. An inline fuse is located in the live wire from the battery. When a light or circuit fails suddenly, please check the fuse first. • Replacing capacity: 100ml • • Take out the oil drain plug for draining, let out all the dirty gear oil. • • 11. Gear oil Please use the recommended gear oil: SAE 5W/90 Stand up the main stand. • 10.
Technical Parameters Size Weight Capacity Circuit system Length Width Height Wheel base 1850mm 680mm 1150mm 1300mm Unloaded weight Mass weight 88kg 242kg Max. Speed Slope 45km/h ≥6º Spark plug Battery Fuse Headlight Turning lights Brake light Indicating lights A7RC 12V / 5.
Technical Parameters Engine Suspension Brake system Model Type Cylinder Bore and stroke Cylinder volume Compression ratio Max. power Max. torque Carburetor Air cleaner Ignition type Starting mode Cooling mode Lubrication 139QMA 4 stroke 1 39 x 41.4mm 49ml 10.5:1 2.61 kW / 8000 (r/min) 3.
17
Baotian Warranty EXCLUSIONS: 1. No liability will be accepted: In the event of a sudden mechanical or electrical failure please contact your supplying dealer. a. For faults reported after 14 days of being discovered. b. For machines used in competition or time trials. Your 24-month warranty covers your scooter/motorcycle in the event of mechanical breakdown or component failure. The first 12 months of cover extends to the entire scooter with the exceptions detailed below.
INITIAL INSPECTION SERVICE 2 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: SERVICE 1 SERVICE 3 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: 19
SERVICE 4 SERVICE 6 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: SERVICE 5 SERVICE 7 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: 20
SERVICE 8 SERVICE 10 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: SERVICE 9 SERVICE 11 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: 21
SERVICE 12 SERVICE 14 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: SERVICE 13 SERVICE 15 Date: Date: Mileage: Mileage: Dealer stamp: Dealer stamp: 22
Maintenance Schedule Engine Oil PDI Gear Oil Battery Spark Plug Fuel Filter Carb Odometer Cable Control Cables Tyre Pressure Tyres / Wheels Brake Fluid Brake System Drive Belt Replace Replace Oil Strainer Air Filter 300 KM Charge Replace Clean Clean Inspect Inspect Inspect Inspect Inspect Adjust Inspect Inspect Inspect Replace 3,000 KM Clean Adjust Lubricate 1,000 KM Adjust Inspect Inspect Clean Adjust Clean Inspect Adjust Inspect Inspect Replace Inspect Replace Clean
