Owner manual

ManualsBrandsBanner ManualsSensorsVALU-BEAM Series

AC- and DC-powered sensors with solid-state outputs

For the latest technical information about this product, including specifications, dimensions, and wiring, see www.BannerEngineering.com

Features

• Choose models for 10 to 30V dc or 24 to 250V ac operation

• DC models have bipolar solid-state outputs: one NPN (sinking) and one PNP

(sourcing)

• AC models have an SPST solid-state output rated for up to 3/4 amp with simple 2-

wire hookup

• All models have a rear panel sensitivity adjustment and light/dark operate switch

• DC models include Banner’s Alignment Indicating Device (AID™) system

• Choose models with integral 2 m (6.5') cable or Mini-style QD (quick-disconnect)

connector; 9 m (30') cables are also available

Opposed Mode Emitter (E) and Receiver (R) Models

OPPOSED

Infrared, 880 nm

Models Range Cable* Supply Voltage Output Type

SMA91E

60 m (200')

2 m (6.5')

10-250V ac/dc -

SMA91EQD 3-pin Mini QD

SM91R 2 m (6.5')

10-30V dc Bipolar NPN/PNP

SM91RQD 4-pin Mini QD

SM2A91R 2 m (6.5')

24-250V ac SPST SCR Solid-state 2-wire

SM2A91RQD 3-pin Mini QD

SMA91ESR

3 m (10')

2 m (6.5')

10-250V ac/dc -

SMA91ESRQD 3-pin Mini QD

SM91RSR 2 m (6.5')

10-30V dc Bipolar NPN/PNP

SM91RSRQD 4-pin Mini QD

SM2A91RSR 2 m (6.5')

24-250V ac SPST SCR Solid-state 2-wire

SM2A91RSRQD 3-pin Mini QD

* 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SMA91E W/30).

A model with a QD connector requires a mating cable; see Quick-Disconnect Cables on page 10.

WARNING: Not To Be Used for Personnel Protection

Never use this product as a sensing device for personnel protection. Doing so could lead to seri-

ous injury or death. This product does NOT include the self-checking redundant circuitry necessary to

allow its use in personnel safety applications. A sensor failure or malfunction can cause either an ener-

gized or de-energized sensor output condition.

VALU-BEAM® 912 Series

P/N 03467_web

Rev. F

4/11/2012

Summary of content (12 pages)

PAGE 1
VALU-BEAM® 912 Series AC- and DC-powered sensors with solid-state outputs For the latest technical information about this product, including specifications, dimensions, and wiring, see www.BannerEngineering.
PAGE 2
VALU-BEAM® 912 Series Retroreflective Mode Models P Visible Red, 650 nm Non-Polarized RETRO Range† Models POLAR RETRO Polarized Cable* Supply Voltage 2 m (6.5') 10-30V dc Output Type Non-Polarized SM912LV SM912LVQD SM2A912LV 0.15 to 9 m (6" to 30') SM2A912LVQD 4-Pin Mini QD 2 m (6.5') 24-250V ac 3-Pin Mini QD Bipolar NPN/PNP SPST SCR Solid-state 2-Wire Polarized†† SM912LVAG SM912LVAGQD SM2A912LVAG 2 m (6.5') 0.3 to 4.5 m (1' to 15') SM2A912LVAGQD 4-Pin Mini QD 2 m (6.
PAGE 3
VALU-BEAM® 912 Series Convergent Mode Models CONVERGENT VISIBLE RED CONVERGENT Visible Red or Infrared; see below Models Range Cable* Supply Voltage Output Type 10-30V dc Bipolar NPN/PNP 24-250V ac SPST SCR Solid-state 2-Wire 10-30V dc Bipolar NPN/PNP 24-250V ac SPST SCR Solid-state 2-Wire Visible Red 650 nm SM912CV SM912CVQD SM2A912CV 2 m (6.5') 38 mm (1.5") Spot Size at Focus: 1.5 mm (0.06") SM2A912CVQD 4-Pin Mini QD 2 m (6.
PAGE 4
VALU-BEAM® 912 Series Glass Fiber Optic Models Infrared 880 nm Watertight o-ring-sealed sensor/fiber interface. GLASS FIBER Models Range Cable* SM912F 2 m (6.5') Range varies with sensing mode and fiber optics used SM912FQD SM2A912F 4-Pin Mini QD 2 m (6.5') SM2A912FQD 3-Pin Mini QD Supply Voltage Output Type 10-30V dc Bipolar NPN/PNP 24-250V ac SPST SCR Solid-state 2-Wire * 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SM912F W/30).
PAGE 5
VALU-BEAM® 912 Series Specifications - DC Models Supply Voltage and Current 10 to 30V dc at 20 mA maximum, exclusive of load; except for SMA91E, ESR and EF emitters, which operate from 10 to 250V ac or dc Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Rating 250 mA continuous, each output Off-state leakage current: less than 10 microamps Output satur
PAGE 6
VALU-BEAM® 912 Series Other DC Models - Cabled bn bk bn + 10-30V dc – bu wh Other DC Models - QD (4-Pin MiniStyle) + 10-30V dc – bu wh Load bk Load Load Load 4-Pin Mini-Style Pinout (Cable Connector Shown) 2 4 1 3 1 = Brown 2 = White 3 = Blue 4 = Black Specifications - AC Models Supply Voltage and Current 24 to 250V ac (50/60 Hz); except for SMA91E, ESR and EF emitters, which operate from 10 to 250V ac or dc Supply Protection Circuitry Protected against transient voltages Output Configura
PAGE 7
VALU-BEAM® 912 Series AC Hookups Emitters - Cabled Emitters - QD (3-Pin Mini-Style) bn bn + + 10-250V ac/dc – bu 10-250V ac/dc – bu 3-Pin Mini-Style Pinout (Cable Connector Shown) bk 1 2 3 Other AC Models - Cabled Other AC Models - QD (3-Pin Mini-Style) bn bn bu bu 24-250V ac Load 1 = Black 2 = Brown 3 = Blue + 24-250V ac – bk Load Excess Gain Mode 1000 EXCESS GAIN Opposed Mode Emitter and Receiver Models EXCESS GAIN 1000 100 10 SMA91E / SM91R, SMA91E / SM2A91R Opposed Mode
PAGE 8
VALU-BEAM® 912 Series Mode 1000 1000 SM912D, SM2A912D SM912DSR, SM2A912DSR Diffuse Mode EXCESS GAIN Diffuse Mode Models EXCESS GAIN Diffuse Mode 100 10 1 1 mm 0.04" 10 mm 0.4" 100 mm 4" 100 10 1 1 mm 0.04" 1000 mm 40" 10 mm 0.4" DISTANCE 1000 mm 40" DISTANCE Visible Red 650 nm 1000 100 mm 4" Infrared 880 nm 1000 SM912CV, SM2A912CV SM912C, SM2A912C EXCESS GAIN Convergent Mode Models EXCESS GAIN Convergent Mode Convergent Mode 100 10 1 1 mm 0.04" 10 mm 0.
PAGE 9
VALU-BEAM® 912 Series Beam Patterns Mode SMA91E / SM91R, SMA91E / SM2A91R 60" 300 mm 1000 mm Opposed Mode 40" 200 mm 20" 100 mm 4" 0 0 500 mm Opposed Mode Emitter and Receiver Models SMA91ESR / SM91RSR, SMA91ESR / SM2A91RSR 1500 mm 0 0 20" 100 mm 4" 1000 mm 40" 200 mm 8" 1500 mm 60" 300 mm 15 m 50' 30 m 100' 45 m 150' 60 m 200' 12" 0 75 m 250' .6 m 2' 1.2 m 4' Non-Polarized SM912LVAG, SM2A912LVAG 6.0" 75 mm 4.0" 50 mm 2.0" 50 mm 2.0" 25 mm 1.
PAGE 10
VALU-BEAM® 912 Series Mode SM912F/SM2A912F 3" 1.9 mm 50 mm 2" 1.3 mm 25 mm 1" 0.7 mm 0 0 25 mm 1" 0.7 mm 0.03" 50 mm 2" 1.3 mm 0.05" 75 mm 3" 1.9 mm 75 mm Opposed Mode 0 Glass Fiber Optic Models IT13S 0 IT23S 100 mm 4" 200 mm 8" 300 mm 12" 0.05" 0.03" BT13S BT23S 0 0.08" 0 400 mm 500 mm 16" 20" 0.08" SM912F/SM2A912F Diffuse Mode 7.5 mm 0.3" 15 mm 0.6" 22.5 mm 0.9" 30 mm 1.2" 37.5 mm 1.
PAGE 11
VALU-BEAM® 912 Series Extension Cables (without connectors) The following cables are available for extending the length of existing sensor cable. These are 30 m (100') lengths of VALU-BEAM cable. This cable may be spliced to existing cable. Connectors, if used, must be customer-supplied.
PAGE 12
VALU-BEAM® 912 Series Mounting Brackets SMB30C SMB30SC 56 • 30 mm split clamp, black PBT bracket • Stainless steel mounting hardware included • Mounting hole for 30 mm sensor A 66 B 13 Hole center spacing: A=ø 45 Hole size: B=ø 27.2 • Swivel bracket with 30 mm mounting hole for sensor • Black reinforced thermoplastic polyester • Stainless steel mounting and swivel locking hardware included 67 B 58 29 A Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 SMB30MM • 12-ga.