User guide

ManualsBrandsBanner ManualsSensorsU-GAGE S18U Series—Analog

Printed in USA 02/05 P/N 108964 rev. A

U-GAGE

™

S18U Series Sensors with Discrete Output

18 mm Ultrasonic Sensors with TEACH-Mode programming

Features

• Fast, easy-to-use TEACH-Mode programming; no potentiometer adjustments

• Short dead zone

• One NPN and one PNP output

• Two bi-colored status LEDs

• Rugged encapsulated design for harsh environments

• Choose 2 meter or 9 meter unterminated cable, or 5-pin Euro-style QD connector

• Wide operating range of -20° to +60°C (-13° to +140°F)

• Choose either straight or right-angle housing

• Temperature compensation

• Configurable for normally open or normally closed operation

• Fast response time (5 milliseconds)

Model

Number

Sensing

Range

Cable*

Supply

Voltage

Output

Housing

Configuration

S18UBA

30 to 300 mm

(1.2" to 11.8")

5-wire, 2 m (6.5') cable

10 to 30V dc

Bipolar

NPN/PNP

Straight

S18UBAQ

5-pin Euro-style QD

S18UBAR

5-wire, 2 m (6.5') cable

Right-Angle

S18UBARQ

5-pin Euro-style QD

Models

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety

applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition.

Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for

personnel protection.

* 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., S18UBA W/30).

A model with a QD connector requires a mating cable; see page 10.

Straight Housing

Right-Angle Housing

Information about analog-output models is available on Banner’s website: www.bannerengineering.com

Ultrasonic Proximity Mode

Ultrasonic

Summary of content (12 pages)

PAGE 1
U-GAGE™ S18U Series Sensors with Discrete Output 18 mm Ultrasonic Sensors with TEACH-Mode programming Features • Fast, easy-to-use TEACH-Mode programming; no potentiometer adjustments Right-Angle Housing • Short dead zone • One NPN and one PNP output • Two bi-colored status LEDs • Rugged encapsulated design for harsh environments • Choose 2 meter or 9 meter unterminated cable, or 5-pin Euro-style QD connector Straight Housing • Wide operating range of -20° to +60°C (-13° to +140°F) • Choose either strai
PAGE 2
U-GAGE™ S18U Series Sensor — Discrete Output Principles of Operation Ultrasonic sensors emit one or multiple pulses of ultrasonic energy, which travel through the air at the speed of sound. A portion of this energy reflects off the target and travels back to the sensor. The sensor measures the total time required for the energy to reach the target and return to the sensor.
PAGE 3
U-GAGE™ S18U Series Sensor — Discrete Output Sensor Programming Two TEACH methods may be used to program the sensor: • Teach individual minimum and maximum limits, or • Use Auto-Window feature to center a sensing window around the taught position. The sensor may be programmed either via its push button, or via a remote switch. Remote programming also may be used to disable the push button, preventing unauthorized personnel from adjusting the programming settings.
PAGE 4
U-GAGE™ S18U Series Sensor — Discrete Output Teaching Minimum and Maximum Limits Normally Open Operation ... Minimum Limit General Notes on Programming • The sensor will return to Run mode if the first Teach condition is not registered within 120 seconds. Output OFF • After the first limit is taught, the sensor will remain in Program mode until the Teach sequence is finished. Output ON Output OFF Normally Closed Operation ...
PAGE 5
U-GAGE™ S18U Series Sensor — Discrete Output Teaching Limits Using the Auto-Window Feature Normally Open Operation ... Taught Position Position - 5 mm Position + 5 mm Output OFF Output ON Output OFF Normally Closed Operation ... ... Position Taught Position - 5 mm Position + 5 mm Output ON Output OFF Output ON Teaching the same limit twice for the same output automatically centers a 10 mm window on the taught position.
PAGE 6
U-GAGE™ S18U Series Sensor — Discrete Output Normally Open/Normally Closed Operation Select The sensor can be configured for either normally open or normally closed operation via the remote teach wire (gray). A series of three pulses on the line will toggle between normally open and normally closed operation. Normally open is defined as the output energizing when the target is present. Normally closed is defined as the output energizing when the target is absent. See Figures 3 and 4.
PAGE 7
U-GAGE™ S18U Series Sensor — Discrete Output Specifications Sensing Range 30 to 300 mm (1.2" to 11.8") Supply Voltage 10 to 30V dc (10% maximum ripple); 65 mA max. (exclusive of load), 40 mA typical @ 25V input Ultrasonic Frequency 300 kHz, rep. rate 2.
PAGE 8
U-GAGE™ S18U Series Sensor — Discrete Output Sensor Response Curves Effective Beam Pattern (Typical) Maximum Target Rotation Angle 2.
PAGE 9
U-GAGE™ S18U Series Sensor — Discrete Output Dimensions Straight Housing Cabled Models QD Models Transducer 6.0 mm (0.24") 80.8 mm (3.18") 53.8 mm (2.12") 10.6 mm (0.42") 53.8 mm (2.12") 90.9 mm (3.58") 18.0 mm (0.71") Right-Angle Housing Cabled Models QD Models 85.1 mm (3.35") 58.0 mm (2.29") 3.6 mm (0.14") Transducer 95.1 mm (3.75") 18.1 mm (0.71") 10.6 mm (0.42") 8.5 mm (0.33") 58.0 mm (2.29") 18.0 mm (0.71") 6.0 mm (0.24") Banner Engineering Corp. • Minneapolis, MN U.S.A. www.
PAGE 10
U-GAGE™ S18U Series Sensor — Discrete Output Accessories Quick-Disconnect Cables Style 5-pin Euro-style straight, with shield Model MQDEC2-506 MQDEC2-515 MQDEC2-530 Length 2 m (6.5') 5 m (15') 9 m (30') Dimensions Pinout ø 15 mm (0.6") 44 mm max. (1.7") M12 x 1 White Brown 38 mm max. (1.5") 5-pin Euro-style right-angle, with shield MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA 2 m (6.5') 5 m (15') 9 m (30') Blue Black Gray 38 mm max. (1.5") M12 x 1 ø 15 mm (0.6") 10 P/N 108964 rev.
PAGE 11
U-GAGE™ S18U Series Sensor — Discrete Output Mounting Brackets • 12-gauge, stainless steel, right-angle mounting bracket with a curved mounting slot for versatility and orientation • Clearance for M4 (#8) hardware SMB18A * Use 4 mm (#8) screws to mount bracket. Drill screw holes 24.2 mm (0.95") apart. 25.4 mm (1.00") 30° 41 mm (1.6") 36.0 mm (1.42") M18 x 1 internal thread 46 mm (1.8") 4.6 mm* (0.18") ø 4.6 mm* (0.
PAGE 12
U-GAGE™ S18U Series Sensor — Discrete Output WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.