Instruction Manual

ManualsBrandsBanner ManualsSensorsU-GAGE Q45U Series—Analog

Piezoelectric proximity mode sensors with push-button programming of sensing window limits

• Ultrasonic proximity detection from 0.25 to 3.0 m (9.8 to 118 inches)

• Push-button TEACH-mode programming of sensing window limits

• Digital filtering for exceptional immunity to electrical and acoustic “noise”

• Selectable 0 to 10V dc voltage sourcing or 4 to 20 mA current sourcing analog out-

puts

• Selectable output slope: positive or negative with increasing target distance

• Wide operating temperature range of –25 to +70 °C; all models include tempera-

ture compensation

• Rugged design for use in demanding sensing environments; rated IEC IP67,

NEMA 6P

• Choose models with integral 2 m (6.5 ft) or 9 m (30 ft) cable, or with Mini-style or

Euro-style quick-disconnect fitting

• Input for remote TEACH-mode programming of window limits

Models

Temperature

Compensation

Cable Supply Voltage Output Type Response Time

Q45ULIU64BCR

Yes

2 m (6.5 ft)

15–24V dc

Selectable 0–10V dc or 4–

20 mA sourcing

Adjustable from 80

milliseconds to 2.56

seconds

Q45ULIU64BCRQ 5-Pin Mini-style QD

Q45ULIU64BCRQ6 5-Pin Euro-style QD

Standard 2 m (6.5 ft) cable models are listed. To order the 9 m (30 ft) cable model, add suffix "W/30" to the cabled model number. For

example, Q45ULIU64BCR W/30. Models with a QD connector require a mating cable.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

Temperature Compensation

All models listed above feature temperature compensation. An increase in air temperature shifts both sensing window limits closer to the

sensor. Conversely, a decrease in air temperature shifts both limits further away from the sensor. The shift is approximately 3.5% of the

limit distance for a 20 °C change in temperature.

Temperature compensated models maintain the position of both sensing window limits to within 1% of each limit distance over the 0 to

+50 °C range, and to within 2.5% over the full operating range of from –25 to +70 °C.

Setting the Near and Far Sensing Limits

The Q45U features a single push button for programming of sensing window near and far limits. For more information, refer to Program-

ming the Window Limits on page 4.

Status Indicators

Status indicator LEDs are visible through the transparent, o-ring sealed acrylic top cover. Indicator function in the Run mode is, as fol-

lows:

Q45U Ultrasonic Sensors with Analog Outputs (Long Range)

P/N 48456 Rev. E 8/21/2013

Summary of content (9 pages)

PAGE 1
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) Piezoelectric proximity mode sensors with push-button programming of sensing window limits • • • • • • • • • Temperature Compensation Models Q45ULIU64BCR Ultrasonic proximity detection from 0.25 to 3.0 m (9.
PAGE 2
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) • The green LED is solid when power is applied to the sensor and flashes to indicate a current output fault. • The red LED is solid when an echo is received and flashes at a rate proportional to echo strength. • The amber LED is solid when the target is within the operating window limits. The 5-segment moving dot LED indicator displays the relative position of the target within the programmed sensing window.
PAGE 3
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) DIP Switch 1: Output Slope Select Voltage/Current-Sourcing Models 20 10 Analog Output (mA) Analog Output (V dc) Positive Slope On = Direct = Output value (voltage or current) increases with increasing distance of the target from the sensor Off* = Inverse = Output value decreases with increasing distance of the target from the sensor 4 0 Near Window Far Window Target Position Figure 3.
PAGE 4
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) Position Response Speed 1 80 milliseconds (2 cycles) 2 160 milliseconds (4 cycles) 3 320 milliseconds (8 cycles) 4 640 milliseconds (16 cycles) 5 1.28 seconds (32 cycles) 6 2.56 seconds (64 cycles) Potentiometer Positions + 1 6 – 2 5 3 4 Figure 4. Response adjustment positions This example shows the potentiometer set at position number 4. There are no numbers on the actual product label.
PAGE 5
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) 8. If the target is held at the same position for programming of both limits, the sensor will establish a 50 mm-wide sensing window, centered on the target position. Specifications Proximity Mode Range Near limit: 250 mm (9.8 inches) min Far limit: 3.0 m (118 inches) max The far limit may be extended as far as 3.
PAGE 6
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) T Step 1 T >2 sec H Access Limit Programming Mode L Wait >0.8 seconds before next input T Step 2 0.04 sec 2 seconds before next input T Step 3 0.04 sec
PAGE 7
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) Hookup Diagrams for Q45U Sensors with Analog Outputs Sensor with Attached Cable bn bk bn + 15–24V dc – bu wh Sensor with 5-pin Mini-style QD wh bk wh bk Remote teach 4 to 20mA Load 0 to 10V Load gy Remote teach (+5–24V dc) shield Banner Engineering Corp recommends the shield wire be connected to earth ground or dc common.
PAGE 8
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) Accessories 5-Pin Mini-Style Cordsets with Shield Model Length MBCC2-506 1.83 m (6 ft) MBCC2-515 4.57 m (15 ft) Style Dimensions Pinout (Female) 61 mm max. (2.4") 7/8-16UN-2B 4 1 3 5 Straight MBCC2-530 2 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Yellow ø 28 mm max. (1.1") 9.14 m (30 ft) 5-Pin Threaded M12/Euro-Style Cordsets with Shield Model Length MQDEC2-506 1.83 m (6 ft) MQDEC2-515 4.57 m (15 ft) MQDEC2-530 9.
PAGE 9
Q45U Ultrasonic Sensors with Analog Outputs (Long Range) SMB30MM • 12-ga. stainless steel bracket with curved mounting slots for versatile orientation • Clearance for M6 (¼ in) hardware • Mounting hole for 30 mm sensor 57 70 C 57 B A Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1 Banner Engineering Corp Limited Warranty Banner Engineering Corp.