Manual

ManualsBrandsBanner ManualsEquipmentSureCross DX80 Wireless Networks

Printed in USA 08/09 P/N 134856 rev. B

SureCross™ DX80K Wireless Conﬁgured Kit

Discrete I/O between a Gateway and 1 Node

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products for personnel protection. Doing so could lead to serious injury or death.

These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A

failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products

catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.

Features

The SureCross™ DX80 is a radio frequency network system built around a Gateway and one

or more Nodes. Conﬁgured kits are packaged in a box with the preset Gateway, Node(s),

accessories, and hardware to get up and running quickly.

Gateway input-to-output mapping provides four discrete (sourcing) inputs and eight •

discrete (sourcing) outputs on the Gateway mapped to eight discrete (sourcing) inputs

and four discrete (sourcing) outputs on the Node

+10 to 30V dc power•

Proprietary radio optimized for effective power management•

Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple •

Access (TDMA) control architecture combine to ensure reliable data delivery within the

unlicensed Industrial, Scientiﬁc, and Medical (ISM) bands

Transceivers provide two-way communication between the Gateway and Node, including •

fully acknowledged data transmission

Site Survey analyzes the network’s signal strength and reliability•

Lost RF links are detected and relevant outputs set to predeﬁned conditions•

For additional information and a complete list of accessories, including FCC approved

antennas, please refer to Banner Engineering’s website, www.bannerengineering.com/

surecross.

Model Power Frequency I/O

DX80K9M6ED1

+10 to 30V dc 900 MHz ISM Band

Discrete Inputs: 4 Sourcing (Gateway), 8 Sourcing (Node)

Discrete Outputs: 8 Sourcing (Gateway), 4 Sourcing (Node)

Models

Summary of content (8 pages)

PAGE 1
SureCross™ DX80K Wireless Configured Kit Discrete I/O between a Gateway and 1 Node Features The SureCross™ DX80 is a radio frequency network system built around a Gateway and one or more Nodes. Configured kits are packaged in a box with the preset Gateway, Node(s), accessories, and hardware to get up and running quickly.
PAGE 2
SureCross™ DX80K Wireless Configured Kit Hookup Diagrams DO8 PWR PWR DI8 DO7 GND GND DI7 DO6 PWR PWR DI6 DO5 GND GND DI5 DO4 DI4 DO4 DI4 DO3 DI3 DO3 DI3 DO2 DI2 DO2 DI2 DO1 DI1 DO1 DI1 Configured input/output mapping I/O Point Terminal Block Label DX80 Gateway DX80 Node Terminal Block Label 1 DI1 Discrete IN 1 Discrete OUT 1 DO1 9 2 DI2 Discrete IN 2 Discrete OUT 2 DO2 10 3 DI3 Discrete IN 3 Discrete OUT 3 DO3 11 4 DI4 Discrete IN 4 Discrete OUT 4 DO4 12 9 DO1
PAGE 3
SureCross™ DX80K Wireless Configured Kit Device Configuration Cycle Power After making any changes to the DIP switch positions, cycle power to the device to activate the changes. For devices with batteries integrated into the housing, remove the battery for one minute to cycle power to the device. Device Settings Rotary Switch Address Mode Extended Address Mode 1 Switches 2 3 4 OFF* ON Do not change the position of any DIP switch other than DIP switch 1. This kit is configured at the factory.
PAGE 4
SureCross™ DX80K Wireless Configured Kit Rotary Dial Positions Rotary Dial Addressing Mode When using Rotary Dial Addressing Mode, the Gateway’s and Node’s rotary dials are in the correct position. The left rotary dial establishes the Network ID and the right dials establish the Device ID. When using multiple networks within range of each other, set each network to a different Network ID using the left rotary dial.
PAGE 5
SureCross™ DX80K Wireless Configured Kit Specifications Many parameters are configurable. The values in the tables represent factory defaults unless otherwise noted. Radio Range* 900 MHz: Up to 4.8 kilometers (3 miles) 2.4 GHz: Up to 3.2 kilometers (2 miles) Transmit Power 900 MHz: 21 dBm Conducted 2.4 GHz: 18 dBm Conducted, ≤ 20 dBm EIRP Spread Spectrum Technology FHSS (Frequency Hopping Spread Spectrum) Antenna Connector Ext. Reverse Polarity SMA, 50 Ohms Antenna Max. Tightening Torque 0.
PAGE 6
SureCross™ DX80K Wireless Configured Kit Outputs Discrete Outputs Gateway: Eight Sourcing Node: Four Sourcing Discrete Output Rating 100 mA max current at 30V dc ON-State Saturation: Less than 3V at 100 mA OFF-state Leakage: Less than 10 µA Discrete Output Update Rate 62.
PAGE 7
SureCross™ DX80K Wireless Configured Kit Notes Banner Engineering Corp. • Minneapolis, MN U.S.A www.bannerengineering.com • Tel: 763.544.3164 P/N 134856 rev.
PAGE 8
SureCross™ DX80K Wireless Configured Kit For more information: Contact your local Banner representative or Banner Corporate Offices around the world. Corporate Headquarters Banner Engineering Corp. 9714 Tenth Ave. North Mpls., MN 55441 Tel: 763-544-3164 www.bannerengineering.com sensors@bannerengineering.com Asia ─ China Banner Engineering China Shanghai Rep Office Rm. G/H/I, 28th Flr. Cross Region Plaza No. 899, Lingling Road Shanghai 200030 CHINA Tel: 86-21-54894500 Fax: 86-21-54894511 www.