Manual

ManualsBrandsBanner ManualsSensorsSL30 Series Slot Sensors

SL Series Slot Sensor

SL0 Series Slot Sensor

Self-contained opposed-mode sensor pair

Printed in USA P/N 60073

SL0 Series Slot Sensor Features

• An easy-to-use self-contained opposed-mode sensor pair in a rugged U-shaped housing

• Easy and economical to mount

• Molded-in beam guides simplify mounting and beam placement

• 30 mm slot width for a wide variety of sensing applications

• Applications include hole detection, gear tooth detection, edge guiding and counting

of opaque materials

• 10 to 30V dc operation

• Bipolar PNP/NPN outputs

• Choose 1 millisecond or 300 microsecond response

• 2 mm effective beam

• Dark or light operate

• Choose integral, unterminated cable or QD models

Models

Slot

Width Cable*

Supply

Voltage

Output

Type Response Repeatability

SL030VB6

SL0 Series Slot Sensor Models

Infrared, 890 nm

1 millisecond 250 microseconds

30 mm

(1.2")

2 m (6.5')

5-wire cable

10-30V dc

Bipolar

NPN (sinking)

and

PNP (sourcing)

5-Pin

Euro-style QD

SL030VB6Q

2 m (6.5')

5-wire cable

5-Pin

Euro-style QD

SL030VB6YQ

SL030VB6Y

300 microseconds 75 microseconds

*NOTES: 1) 9 m (30') cables are available by adding suffix “W/30” to the model number of the cabled version (e.g., SL030VB6 W/30).

2) A model with a QD connector requires an accessory mating cable. See page 4.

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications.

A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety

Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.

Summary of content (4 pages)

PAGE 1
SL0 SeriesSlot SlotSensor Sensor SL Series Self-contained opposed-mode sensor pair SL0 Series Slot Sensor Features • An easy-to-use self-contained opposed-mode sensor pair in a rugged U-shaped housing • Easy and economical to mount • Molded-in beam guides simplify mounting and beam placement • 30 mm slot width for a wide variety of sensing applications • Applications include hole detection, gear tooth detection, edge guiding and counting of opaque materials • 10 to 30V dc operation • Bipolar P
PAGE 2
SL0 Series Slot Sensor SL0 Series Slot Sensor Overview The SL0 Series Slot Sensor (sometimes called a “Fork Sensor”) comprises an opposed-mode emitter and its receiver inside a single convenient housing. Opposed-mode sensing is very reliable, and the single self-contained housing provides easy installation, with no sensor alignment required.
PAGE 3
SL0 Series Slot Sensor 30.2 mm (1.19") 10.9 mm (0.43") 10.0 mm (0.39) 45.0 mm (1.77") 72.0 mm (2.84") Power LED (Green) Signal LED (Yellow) 6.0 mm (0.24") 40.0 mm (1.58") 6.0 mm (0.24") 20.2 mm (0.80") 2x ø5.6 mm (0.22") 52.0 mm (2.05") M12 x 1 18.8 mm (0.74") Figure 3. SL0 Series Slot Sensor dimensions SL0 Series Slot Sensor Specifications Slot Opening 30 mm (1.2") wide x 45 mm (1.8") deep overall; beam set in 10 mm (0.
PAGE 4
SL0 Series Slot Sensor Accessories Quick-Disconnect Cables The following cables are available for SL0 Series Slot Sensor QD models Style 5-pin Euro-style straight Model Length MQDC1-506 MQDC1-515 MQDC1-530 Dimensions 2 m (6.5') 5 m (15') 9 m (30') Pin-out ø 15 mm (0.6") M12 x 1 44 mm max. (1.7") White Wire Brown Wire 38 mm max. (1.5") Blue Wire Black Wire 5-pin Euro-style right-angle MQDC1-506RA MQDC1-515RA MQDC1-530RA Gray Wire 2 m (6.5') 5 m (15') 9 m (30') 38 mm max. (1.