Manual

ManualsBrandsBanner ManualsSensorsQ60 Background Suppression Series

Q60AF Sensors

Long-Range Self-Contained Adjustable-Field Sensors

Printed in USA 06/02 P/N 67003 rev. B

Q60AF Adjustable-Field Features

• Long-range adjustable-field background suppression sensor detects objects within a defined

sensing field, while ignoring objects located beyond the sensing field cutoff

•Two-turn, logarithmic adjustment of sensing field cutoff point from 0.2 to 2 m; allows easy

setting of cutoff point at long range

• Rotating pointer indicates relative cutoff point setting

• Easy push-button or remote programming of light/dark operate and output timing;

continuous status indicators verify all settings at a glance

• Output ON and/or OFF delays adjustable from 8 milliseconds to 16 seconds

• Powerful infrared sensing beam

•Tough ABS/polycarbonate blend housing is rated IEC IP67; NEMA 6

10-30V dc Models (Q60BB6AF):

• Powered by 10 to 30V dc; bipolar (one NPN and one PNP) outputs

•Available with integral cable or rotating Euro-style quick-disconnect fitting

Universal Voltage Models (Q60VR3AF):

• 12-250V dc or 24-250V ac, 50/60 Hz

•Available with integral cable or rotating Micro-style quick-disconnect fitting

Infrared, 880 nm

Q60 Adjustable-Field Models

* 9 meter cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q60BB6AF2000 W/30).

A model with a QD connector requires a mating cable; see page 8.

Q60BB6AF2000

50 mm

to 125 mm

(2" to 5")

depending

on cutoff

point setting

5-wire

2 m (6.5')

10-30V dc

Bipolar

NPN/PNP

100

.10 m

.33 ft

1.0 m

3.3 ft

10 m

33 ft

.01 m

.033 ft

DISTANCE

1000

10000

Q60AF

Models

Minimum

Range Cable*

Supply

Voltage

Output

Type

Excess Gain at

200 mm Cutoff

Adjustable:

200 mm to

2000 mm

(8" to 80")

Cutoff

Point

100

.10 m

.33 ft

1.0 m

3.3 ft

10 m

33 ft

.01 m

.033 ft

DISTANCE

1000

10000

Q60AF

Excess Gain at

2000 mm Cutoff

Q60BB6AF2000Q

5-pin

Euro-style

WARNING . . .

Not To Be Used for Personnel Protection

Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or

malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety

products which meet OSHA, ANSI and IEC standards for personnel protection.

Q60VR3AF2000

5-wire

2 m (6.5')

Universal

Voltage

12-250V dc

24-250V ac

E/M Relay

(SPDT),

normally

closed and

normally open

contacts

Q60VR3AF2000Q1

4-pin

Micro-style

E/M Relay

(SPST),

normally

open

contact

Summary of content (8 pages)

PAGE 1
Q60AF Sensors Long-Range Self-Contained Adjustable-Field Sensors Q60AF Adjustable-Field Features • Long-range adjustable-field background suppression sensor detects objects within a defined sensing field, while ignoring objects located beyond the sensing field cutoff • Two-turn, logarithmic adjustment of sensing field cutoff point from 0.
PAGE 2
Q60 Series Adjustable-Field Sensors Q60AF Overview The Q60AF sensor is a full-featured adjustable-field sensor. These adjustable-field sensors are able to detect objects of relatively low reflectivity, while ignoring other objects in the background (beyond the cutoff point). The cutoff distance is mechanically adjustable, using the 2-turn adjustment screw on the sensor top (Figure 1). A rotating pointer indicates the relative cutoff position. (The indicator moves clockwise to show increasing distance.
PAGE 3
Q60 Series Adjustable-Field Sensors Sensor Setup Target Background Setting the Cutoff Distance The cutoff distance for Q60AF sensors may be adjusted between 200 mm and 2000 mm (8" to 80"). R1 R2 E Cutoff Distance NOTE: Setting the cutoff distance adjustment screw to its maximum clockwise position places the receiver lens directly in front of the receiver elements and results in the Q60 performing as a long-range diffuse sensor. nce sta Increas ing Di Figure 4.
PAGE 4
Q60 Series Adjustable-Field Sensors Color Sensitivity The effects of object reflectivity on cutoff distance, though small, may be important for some applications. It is expected that at any given cutoff setting, the actual cutoff distance for lower reflectance targets will be slightly shorter than for higher reflectance targets (see Figure 10). This behavior is known as color sensitivity.
PAGE 5
Q60 Series Adjustable-Field Sensors To set a delay, single-click the appropriate button or pulse the remote wire as shown in Figure 14 to enable the process. Then use the + or – button or the appropriate remote wire pulse procedure to increase or decrease the delay (single-click adjusts the delay by one step at a time, and holding the button in provides a rapid increase/decrease). NOTE: Remote wire available on models Q60BB6AF(Q1) only.
PAGE 6
Q60 Series Adjustable-Field Sensors Light/Dark Operate Select Light Operate or Dark Operate mode may be selected using the two push buttons or a 4-second pulse of the remote line to toggle between the selections. See Figure 15. Push Button Lockout For security, the push buttons may be locked out using either the remote line or the push buttons themselves. See Figure 16. Remote Push Button Push Button Lockout Toggle Four-Second Press and Hold + ON DELAY – Figure 15.
PAGE 7
Q60 Series Adjustable-Field Sensors Q60 Specifications, continued Output Rating Q60BB6AF models 150 mA maximum each output @ 25° C Off-state leakage current: < 5µA @ 30V dc Output saturation NPN: < 200 mV @ 10 mA and < 1V @150mA Output saturation PNP: < 1V at 10 mA; < 1.5V at 150 mA Q60VR3AF Universal models Min. voltage and current: 5V dc, 10 mA Mechanical life of relay: 50,000,000 operations Electrical life of relay at full resistive load: 100,000 operations Max.
PAGE 8
Q60 Series Adjustable-Field Sensors Q60 Adjustable-Field Hookups 5-Pin Euro-Style Pin-out Q60BB6AF2000(Q) (Cabled and QD Models) 10 to 30V dc bn wh bk (Cable Connector Shown) + 10-30V dc – bu (Cabled Model) 24 to 250V ac (50/60Hz) or 12 to 250V dc White Wire 24 to 250V ac (50/60Hz) (Cable Connector Shown) or 12 to 250V dc bn Brown Wire rd/wh Blue Wire wh Gray Wire NC ye Load gy rd C bk Remote Program Green Wire rd/bk AC/DC bu Black Wire Load Q60VR3AF2000Q1 4-Pin Micro-Style Pin-o