Owner manual

ManualsBrandsBanner ManualsSensorsQ45 Laser DC Series

1

2

3

4

5

6

7

Printed in USA 05/07 P/N 38244 rev. B

Q45BB6LL Series – Laser Diode Retroreflective Sensors

†

Very-Long-Range Retroreflective Sensors for 10 to 30V dc

WARNING . . . Not To Be Used for Personnel Protection

Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor

failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products

catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.

Features

• High power and small effective beam for retroreflective sensing applications

• Class II laser diode light source; operates from 10 to 30V dc

• 40 m (130') range for polarized models and 70 m (225') range for non-polarized

models, using supplied BRT-2x2 target

• Bipolar NPN (sinking) and PNP (sourcing) solid-state outputs, switchable light and

dark operate; 250 mA maximum load

• Top mounted Power, Signal (AID™ System), and Output indicator LEDs

• Optional plug-in Pulse or Delay timing logic and display modules

• Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67

rating

†

U.S. Patent(s) issued or pending

Models

Model Cable* Range

Supply

Voltage

Output

Type

Excess Gain

Non-Polarized

Visible red,

655 nm

Q45BB6LL

Q45BB6LLQ

Q45BB6LLQ6

5-wire 2 m (6.5')

5-Pin Mini-style QD

5-Pin Euro-style QD

0.3–70 m

(1'–225')

w/BRT-2x2

(included)

10 to

30V dc

Bipolar

NPN/

PNP

Polarized

Visible red,

655 nm

Q45BB6LLP

Q45BB6LLPQ

Q45BB6LLPQ6

5-wire 2 m (6.5')

5-Pin Mini-style QD

5-Pin Euro-style QD

0.6–40 m

(2'–130')

w/BRT-2x2

(included)

* 9 m cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45BB6LL W/30).

A model with a QD connector requires a mating cable; see page 6.

L

I

S

T

E

D

1

10

100

1 m

3.3'

10 m

33'

100 m

333'

0.1 m

0.3'

1000

E

X

C

E

S

S

G

A

I

N

DISTANCE

Q45BB6LL (Q)

Retroreflective

Mode

BRT-THG

Tape

BRT 2 x 2

Reflector

1

10

100

1 m

3.3'

10 m

33'

100 m

333'

0.1 m

0.3'

1000

E

X

C

E

S

S

G

A

I

N

DISTANCE

Q45BB6LLP (Q)

Polarized

Retroreflective

Mode

BRT-THG

Tape

BRT 2 x 2

Reflector

P

POLAR RETRO

RETRO

Summary of content (8 pages)

PAGE 1
Q45BB6LL Series – Laser Diode Retroreflective Sensors† Very-Long-Range Retroreflective Sensors for 10 to 30V dc Features • High power and small effective beam for retroreflective sensing applications • Class II laser diode light source; operates from 10 to 30V dc • 40 m (130') range for polarized models and 70 m (225') range for non-polarized models, using supplied BRT-2x2 target • Bipolar NPN (sinking) and PNP (sourcing) solid-state outputs, switchable light and dark operate; 250 mA maximum load • Top mou
PAGE 2
Q45BB6LL Series – Laser Retroreflective Sensors Overview Status indicator LEDs for Power, Signal and Output are clearly visible beneath a raised dome in the sensor’s transparent o-ring-sealed polycarbonate cover. The Power indicator lights whenever power is applied to the sensor. The Signal LED lights whenever the sensor sees its modulated light source, and pulses at a rate proportional to the strength of the received light signal; this is the AID™ Alignment Indicating Device.
PAGE 3
Q45BB6LL Series – Laser Retroreflective Sensors CAUTION . . . Never stare directly into the sensor lens. Laser light can damage your eyes. Avoid placing any mirror-like object in the beam. Never use a mirror as a retroreflective target. CAUTION . . . This sensor contains no user-servicable components. Do not attempt to repair. Incorrect component values may produce hazardous laser radiation levels.
PAGE 4
Q45BB6LL Series – Laser Retroreflective Sensors Specifications Supply Voltage and Current 10 to 30V dc (10% maximum ripple), at less than 50 mA (exclusive of load) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Bipolar: one current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Rating 250 mA maximum each output up to 50° C, derated to 150 mA at 70° C (derate 5 mA/°C) Off-state leakage current: less than 1 micro
PAGE 5
Q45BB6LL Series – Laser Retroreflective Sensors Dimensions Cabled Models Transparent Cover (Gasketed) View: Sensing Status Output Load Status Power Open to Access: Sensitivity (Gain) Adjustment Timing Adjustments Light/Dark Operate Switch 5-Pin Mini-Style Quick-Disconnect Models 54.1 mm (2.13") 5-Pin Euro-Style Quick-Disconnect Models Emitter Axis 28.6 mm (1.13") 44.5 mm (1.75") Lens Centerline 50.8 mm (2.00") 69.0 mm (2.72") 6.4 mm (0.25") 87.6 mm (3.45") 4.5 mm (#10) Screw Clearance (2) 7.1 mm (0.
PAGE 6
Q45BB6LL Series – Laser Retroreflective Sensors Accessories Quick-Disconnect (QD) Cables Cable: PVC jacket; polyurethane connector body; nylon coupling nut (Mini), chrome-plated brass coupling nut (Euro) Conductors: 18 AWG (Mini), 22 or 20 AWG (Euro) high-flex stranded, PVC insulation, gold plated contacts Temperature: –40° to +80° C (–40° to +176° F) (Mini); –40° to +90° (–40° to +194° F) (Euro) Voltage Rating: 250V ac/300V dc Style 5-Pin Euro-Style Straight 5-Pin Mini-Style Straight Model MQDC1-506 MQD
PAGE 7
Q45BB6LL Series – Laser Retroreflective Sensors Accessories, continued Output Timing Logic and Signal Strength Display Modules Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a seven-element display which gives a more precise indication of excess gain than does the AID™ system LED that is standard on Q45 sensors. The modules listed below may be used with all Q45BB6 Series sensors.
PAGE 8
Q45BB6LL Series – Laser Retroreflective Sensors WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.