Beo4 Guide
Contents Using your Beo4 remote control, 3 Beo4 buttons in detail, 4 • Daily and advanced operation with Beo4 buttons Customise Beo4, 5 • Add an extra ‘button’ • Move extra ‘buttons’ • Remove an extra ‘button’ • Set up Beo4 • Beo4 zones (ZONE?) • Beo4 options (OPTION?) • Beo4 configuration (VIDEO?) • Beo4 modes (MODE?) • Reset your Beo4 (RESET?) Conversion, 12 Maintenance, 13 • Cleaning Beo4 • Changing the batteries Lexicon, 14 1006 Technical specifications, features and the use thereof are subject to ch
Using your Beo4 remote control 4 5 1 2 6 3 LIST 0 MENU STOP BACK Daily operations are carried out by pressing a single button on Beo4, or by pressing a few buttons in a logical and straightforward sequence. But the Beo4 remote control incorporates more functions than just the actual buttons. Extra sources can be switched on, and additional functions can be obtained via the display. “Buttons” for these functions can be brought up on the Beo4 display via the LIST button.
Beo4 buttons in detail … Move your mouse around this illustration for information about the Beo4 buttons.
Customise Beo4 … The Beo4 buttons give direct remote control of a large number of functions, and the Beo4 display gives you access to even more functions. Whenever a source is displayed on Beo4 (TV, RADIO, etc.), you can press the LIST button and bring up extra functions in the display to help you operate that source, just as if you were bringing up extra buttons. You can also switch on extra equipment connected to your television.
>> Customise Beo4 … Add an extra ‘button’ to Beo4, either to the preset position or to a specific position. 3 Add an extra ‘button’ When you add a new function to the Beo4 list, you can bring up this new ‘button’ in the Beo4 display. > > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display.
>> Customise Beo4 … 3 Move extra ‘buttons’, either to the top of the list or to a specific position. Move extra ‘buttons’ You can rearrange the order in which the extra ‘buttons’ appear when you press LIST. > > > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display MOVE? on Beo4.
>> Customise Beo4 … Remove an extra ‘button’ You can remove any of the extra ‘buttons’ that are available when you press LIST. > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display REMOVE? on Beo4. Press the centre button and use to select AV?, LIGHT? or CNTROL? Press the centre button to bring up the list of extra ‘buttons’. The first ‘button’ appears in the display.
>> Customise Beo4 … Set up Beo4 If you buy a new Beo4 you can set it up for your television. > > > > > > > > Press and hold the standby button down. Press LIST to get access to the Beo4 setup function. Let go of both buttons. ADD? appears in the display. Press LIST or to display ZONE?, CONFIG? or MODE? on Beo4. Press the centre button to select the setup you want. Press or to display the setting you want on Beo4. Press the centre button to store the configuration.
>> Customise Beo4 … Beo4 options (OPTION?) Appears when you access the Beo4 setup mode. Enables you to preprogram a Bang & Olufsen system setup. V.OPT Video options A.OPT Audio options L.OPT Link options For further information, refer to the Guide enclosed with your product. Beo4 configuration (VIDEO?) For selecting a dedicated video product setup for Beo4. VIDEO 5 Supports, for example, video products for the American and European markets.
>> Customise Beo4 … Beo4 modes (MODE?) MODE 1 When a Beo4 remote control is in MODE 1, the navigation button is used for menu operation, and menu and source operation are separated. MODE 1 should be used if: – all your televisions in your video setup contain the ‘REMOTE CONTROL’ or ’BEO4 SETTING’ menu and are set to ‘NAVIGATION BUTTON’. MODE 2 When a Beo4 remote control is in MODE 2, the navigation button does not work and menu and source operation are not separated.
Conversion … TV TV LIGHT RADIO DTV DVD CD V MEM TEXT A MEM 7 8 9 4 5 6 1 2 3 LIST 0 MENU LIGHT RADIO DTV DVD CD V MEM RECORD A MEM 7 8 9 4 5 6 1 2 3 TEXT 0 MENU GO LIST EXIT STOP STOP PLAY BACK Beo4 - type 1621/22/24/25 Beo4 - type 1710 12 New functions on Beo4 (type 1710) RECORD is in the LIST menu and is used to make a recording. PLAY starts playback of a DVD, recording etc. BACK is used to step back in menus and closes the LIST menu.
Maintenance … CAUTION! Do not expose batteries to excessive heat such as sunshine, fire or the like! 2 1 3 2 1 Cleaning the Beo4 … Wipe the Beo4 remote control with a soft, lint-free, wet cloth which is wrung firmly. Changing the batteries When BATTERY appears in the Beo4 display, it is time to change the batteries in the remote control. The Beo4 requires three batteries (placed under the lid on the back). We recommend that you use 1.5 volt (size AAA) Alkaline batteries only.
Lexicon … A A.AUX (audio auxiliary source) For switching on any extra equipment connected to your Bang & Olufsen audio system. ADD? Appears as an option in the Beo4 setup mode. Enables you to add extra “buttons” to the Beo4 display. Refer to ‘Add an extra ‘button’’. A-DTV2 For selecting AV and then DTV2. A-DVD2 (AV video recorder 2) For selecting AV and then DVD2. A.MEM (audio recorder) Appears in the display when you press the Beo4 A MEM button.
>> Lexicon … CLEAR For clearing program numbers on recent Bang & Olufsen TV sets. In order to get access to CLEAR, V.SETUP must be added first. CLOCK Displays the time on certain Bang & Olufsen products. Refer to the relevant User Guide for further information. CNTROL? For configuring control of windows, curtains etc. Refer to CONTROL. CONFIG? Enables you to program a dedicated product setup for Beo4. CONTROL Used to control non–Bang & Olufsen products, e.g. windows, curtains etc.
>> Lexicon … J JOIN Is a Master Link function. Press LIST repeatedly to bring up JOIN in the Beo4 display. You are connected to the active source in the system. In standby mode radio will be used as source. L LAMP (lamp light control) For switching on a particular lamp in your light setup – requires the installation of a Bang & Olufsen light control unit.
>> Lexicon … LOUDNSS (loudness) For switching the loudness function on/off in certain Bang & Olufsen systems. LOUDNSS is only available if A.SETUP or V. SETUP has been added. The loudness function compensates for the human ear’s lack of sensitivity to high and low bass and treble levels when listening to low volume levels. Press LIST repeatedly to bring up LOUDNSS in the Beo4 display and then press the centre button repeatedly to set loudness to on or off.
>> Lexicon … P-AND-P (picture-and-picture) For operating the picture-and-picture function on certain Bang & Olufsen TVs. Press, for example, the TV button to bring up the source TV in the picture to the right. PICTURE For operating the various functions related to the PICTURE button on other recent Bang & Olufsen remote controls. In older video systems, it may relate to functions such as motorised stand, picture-and-picture, as well as picture adjustment. V.
>> Lexicon … S SELECT Is used for programming a sequence of compact discs for playback on BeoSound 9000. SETUP For setting up the LC 2 Light Control. SHIFT For operating certain functions related to set-top box operation in a link room. Certain other functions may also require that SHIFT is displayed first. SLEEP For setting a sleep timer on the television using Beo4. Press LIST repeatedly to bring up SLEEP in the Beo4 display and press the centre button repeatedly to set different sleep timers.
>> Lexicon … TV Appears in the display when you press the Beo4 TV button. Any operation you carry out on the Beo4 will be directed to your Bang & Olufsen TV. U UPDATE (Teletext update) For operating the Teletext update function in Bang & Olufsen TVs. Press the centre button. Repeat the operation to see the page when it has been updated. V V.AUX (auxiliary video source) For switching on any extra video equipment connected to your Bang & Olufsen video system. Press the centre button. V.
