23456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 12345678901234567890123456789012123456
#89815 Part Drawing 1/4 Round Conference Table Description P1 Top Platform P2 Left Leg Part Qty 1 EA P8 Drawing Description Crossbrace Qty 1 EA 1 EA Hardware List P3 P4 P5 Right Leg (with Spring) Metal Stability Panel A 9/16” Socket Screw 4 EA A1 1-3/8” Socket Screw 2 EA B 1-7/8” Socket Screw 4 EA C Plastic Grommet 1 EA D 2” Locking Caster 4 EA E Allen Wrench 1 EA Caster Wrench 1 EA 1 EA 1 EA Welded Rod Assembly 1 EA P6 Left Side Handle 1 EA F P7 Right Side H
Flipper-1/4 Round Assembly Diagram READ THROUGH INSTRUCTIONS FROM BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT. 1.) Identify and Separate all the Parts and Hardware. 2.) Slide the Right Side Handle (P7) Through the Right Leg (P-3) and into the Welded Rod (P5) as shown in illustration #1. Rotate Right Side Handle (P7) until holes are aligned (See illustration#1). Secure using 1 Screw (A). 3.
.) Attach Metal Stability Panel (P4) and Crossbrace (P-8) to the Right Leg (P-3) and Left Leg (P2) using 2 Screws (A) and 2 Screws (A1) as shown in illustration #2. P3 P2 P4 A1 P8 (A) Screw M6 X 9/16” For Scale only A (A1) Screw M6 X 1-3/8” For Scale only 5.) Insert Spring on Right Leg (P3) into the notch in Welded Rod (P5) as shown in illustration # 3.
6.) Place the Top Platform (P1) with the insert nuts facing up. Attach Right Leg (P-3) and Left Leg (P2) using 4 each (B) screws as shown in illustration #4. (Finger tighten only) 7.) Attach 4 each (D) Locking Casters to the front and back of the Right Leg (P-3) and Left Leg (P2). Tighten Casters using Caster Wrench (F). (Tighten all screws using Allen Wrench (E).
8.) To install Grommet (C), separate parts and press Grommet Sleeve in rectangular openings in Top Platform (P1) as shown in illustration #5. Grommet(D) installation Illustration #5 Grommet (C) 9.) Snap 2 plastic Caps over top of Sleeve as shown in illustration #5. Cap Cap Sleeve Cap Cap Sleeve C P1 Important The Balt product you have purchased is guaranteed against material and workmanship defects. This guarantee extends 1 year from date of purchase.
TT-Connect PlatesPart Drawing P-1 Description Connecting Plate Connecting Flipper Tables Part Qty Drawing Description Qty Hardware List 1 EA A READ THROUGH INSTRUCTIONS FROM BEGINNING TO END BEFORE STARTING TO ASSEMBLE UNIT. 1.) Identify and Separate all the Parts and Hardware. 2.) Place 2 Flipper tables end to end, or other configuration as desired. Attach TT- Connecting Plate to both tables using 4 Wood Screws (A) as shown in illustration # 1.
#89815 1/4 Round Conference Table For more information 1-800-749-2258 48” 24” 26” 29½ 28½” 22 Shipping Information 4.8 Cubic Feet 57 lbs.
#89815 1/4 Round Conference Table Layout 9
