23456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 12345678901234567890123456789012123456
#89868 Single Floor Carrel Part Drawing Description Part Qty Drawing Description Qty Hardware List P-1 P-2 P-3 P-4 P-5 P-6 P-7 P-8 P-9 Left Side Panel Right Side Panel Top Panel Back Panel Keyboard Panel Left Leg Right Leg Left Keyboard Slide 1 EA A Socket Screw M5X15 mm 2 EA A1 Wood Screw #6X½ 8 EA A2 Wood Screw #8X1¼ 2 EA 1 EA B 1 EA Interior Threaded Post 2 EA C Cam Lock 14 EA D Cam Post 14 EA E Wood Dowel 4 EA F Glide Bracket 2 EA G Glide 4 EA H Grom
#89868 Single Floor Carrel Assembly Diagram Illustration # 1 D D D P-7 E P-6 E Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time Toll-Free Customer Service 1-800-749-2258 To Assemble: 1. Identify and Separate all the Parts and Hardware. 2. Place the Left Leg (P-6) and Right Leg (P-7 ) with the three threaded holes facing up. Install 5 Cam Posts (D) in each Leg as shown in illustration # 1. 3.
l 5. Place the Left Side Panel (P-1) with the Predrilled holes Be sure that arrow on top of Camlock (C) aligns with centerline of Edge Drilled hole. facing up and install 2 each Cam Posts (D) in the 2 threaded insert nuts (Pre-installed) as shown in illustration # 2. Phillips Screwdriver Arrow 6. Install 2 each Dowels (E) into the holes as shown in illustration # 2. 7. Attach Left Side Panel (P-1) to Left Leg (P-6 ) as shown in illustration # 2.
11.Place the Right Side Panel (P-1) with the Predrilled holes facing up and install 2 each Cam Posts (D) in the 2 threaded insert nuts (Pre-installed) as shown in illustration # 3. Phillips Screwdriver Be sure that arrow on top of Camlock (C) aligns with centerline of Edge Drilled hole. Arrow 12.Install 2 each Dowels (E) into the holes as shown in illustration # 3. 13.Attach Right Side Panel (P-2) to Right Leg (P-7 ) as shown in illustration # 3.
P-3 17.Slide Top Panel (P-3) over the Wood Dowels (E) and the Camposts (D) in the Left Side Panel (P-1) as shown in illustration #4. Secure by turning the Cam Locks (C) 1/4 turn until they lock. P-4 A2 18. Slide Back Panel (P-4) over the Campost (D) in the Left Leg (P-6) as shown in illustration # 4. Secure by turning the Cam Locks (C) 1/4 turn until they lock. C C D 19. Secure Back Panel (P-4) to Top Panel (P-3) using 2 Wood Screws (A2) as shown in illustration # 4.
Illustration # 6 Keyboard Slide Assembly P-1 22.Attach Keyboard(P-5) to Left Keyboard Slide (P-8) and Right Keyboard Slide (P-9)using 4 Wood Screws (A1) as shown in illustrations # 6. A1 P-2 P-8 P-5 23. Tighten Screws (A1) using Phillips Screwdriver. To install Grommets: 24. Insert Grommet Sleeve (H) in Round openings in Top Platforms (P-2) as shown in illustration #7. 25. Snap Grommet Cap (J) into Grommet Sleeve (H) as shown in illustration #7.
