23456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 123456789012345678901234567890121234567890123456789012345678901212345678901234 12345678901234567890123456789012123456
#89843 Single Student Training Table Part Drawing P-1 P-2 P-3 P-4 Description Left Side Panel 1 EA Right Side Panel 1 EA Bottom Panel 1 EA Table Top Top Support 2 EA P-6 Top Front Brace 1 EA P-7 Bottom Front Brace 1 EA P-8 Back Panel 1 EA P-9 Upper Leg Mount 1 EA P-10 Lower Leg Mount 1 EA P-12 P-13 Leg Upright Metal Panel Drawing Description Qty P-14 Keyboard Bracket 4 EA P-15 Keyboard Slide 2 EA Hardware List 1 EA P-5 P-11 Part Qty A Socket Screw M6X28mm 4 EA
#89843 LX-48 Assembly Diagram To Assemble: 1.Identify and Separate all the Parts and Hardware. 2. Place Leg Upright (P-11) on a flat surface as shown in illustration # 1. [ with 2 large holes facing up ] A2 3. Attach Upper Leg Mount (P-9) and Lower Leg Mount (P-10) using 4 each Phillips Screws (A2) as shown in illustration # 1. P-9 Illustration # 1 A2 Note: 4 Holes are located near Upper Leg Mount (P-9) as shown in illustration # 1 P-11 P-10 4.
Note: Camlocks can be turned with Allen Wrench, or Large Phillips Screwdriver 7.Place the Right Side Panel (P-2) with the Predrilled holes facing up and install 2 each Cam Posts (D) in the 2 threaded insert nuts (Pre-installed) as shown in illustration # 3. 8. Install 2 each Cam Locks (C) in the 2 large holes. P-2 9. Install 8 Wood Dowels (E) into the holes as shown in illustration # 3. Illustration # 3 D E C Phillips Screwdriver Be sure that 6.
11.Slide Bottom Panel (P-3) over the Wood Dowels (E) and the Camposts (D) in the Right Side Panel (P-2) as shown in illustration #5. Secure by turning the Cam Locks (C) 1/4 turn until they lock. 12.Slide 2 Top Supports (P-5) over the Wood Dowels (E) in the Right Side Panel (P-2). Illustration # 5 P-5 P-5 P-3 E D C 17. E P-2 D To Secure Cam Locks, Insert Large Phillips Head Screwdriver and turn Cam Lock 1/4 turn (90 degrees) clockwise. Illustration # 6 F1 P-5 P-7 P-1 E P-3 13.
17.Slide Back Panel (P-8) into groove in the Left Side Panel (P1) and the Right Side Panel (P2) as shown in illustration # 7. P-2 P-8 Attach Top Front Brace (P-6) to the Left 18. Side Panel (P1) and the Right Side Panel (P2) using 4 Screws (B). Illustration # 7 B B P-1 20. Install 4 Wood Dowels (E) into the 4 holes in the Table Top (P-4) as shown in illustration # 8. P-6 21.Slide Wood CPU Assembly over the Wood Dowels (E) and the Camposts (D) in the Table Top (P-4) as shown in illustration # 8.
Illustration # 9 25. P-15 P-15 A3 A3 Attach 2 Keyboard Brackets (P-14) to 1 Keyboard Slide (P-15) using 2 Screws (A3) as shown in illustrations # 9. 26. Attach 2 Keyboard Brackets (P-14`) to 2nd Keyboard Slide (P-15) using 2 Screws (A3). Note: The 2 Slides will have Brackets on the opposite sides. P-14 P-14 P-14 27. Attach 2 Keyboard Slides (P-15) to the Plastic Keyboard Tray (P-13) using 4 Screws (B2) as Illustration #10 P-15 shown in illustrations # 10. B2 P-13 B2 P-15 28.
Illustration#12 31.Attach Metal Panel (P-12) to the Left Leg Assembly using 2 Phillips Screws (A1) as shown in illustrations # 12. B1 32.Attach Metal Panels (P-12) to the Wood CPU Assembly using 2 Wood Screws (B1) as shown in illustrations # 12. A1 B1 A1 Illustration#13 P-12 H G P-4 33. Insert 1 Grommet Sleeve (G) in Round opening in Table Top (P-4) as shown in illustration #13. 34. Snap Grommet Cap (H) into Grommet Sleeve (G) as shown in illustration #13.
