Installation Guide

BF-IDU07
BIS U-620-068-1X1-00-SX
Ultra High Frequency Passive Radio Frequency,
Identification Processor
INSTALLATION GUIDE
This document provides instructions and information
designed to assist users in the hardware setup of the BIS U-
620-068-1x1-00-Sx Processor. For configuration details see
the BIS U-62_ Processor Manual.
PACKAGE CONTENTS
Qty
Description
1
BIS U-620-068-1x1-00-Sx Processor
1
UHF Series Configuration Tag
1
This Installation Guide
TECHNICAL DATA
ELECTRICAL FEATURES
Power Supply
19.2…28.8 V DC
DC Input Current
1 A
Communication Interface
Baud Rate
RS232
9600 (default) … 115200
RADIO FEATURES
EU
US
Frequency (MHz)
ETSI EN 302 208
865…868
-
FCC part 15.247
-
902…928
Number of Channels
4 fixed
50 hopping
Frequency Tolerance
± 10 ppm over entire temp
range
Air Interface
EPC C1G2
Conducted Output Power
500 mW (27 dBm) max
Antenna Connector
Reverse TNC
ENVIRONMENTAL FEATURES
Operating Temperature
-20…+50 °C
(-4…+122 °F)
Storage Temperature
-20…+70 °C
(-4…+158 °F)
Humidity max.
90 % non condensing
Vibration Resistance
EN 60068-2-6
14 mm @ 2…10 Hz;
1.5 mm @ 13…55 Hz;
2 g @ 70…200 Hz;
2 hours on each axis
Shock Resistance
EN 60068-2-27
30 g; 11 ms;
3 shocks on each axis
Protection Class
EN 60529
IP65*
PHYSICAL FEATURES
Dimensions
164 x 112 x 48 mm
(6.46 x 4.41 x 1.88 in)
Weight
560 g (19.8 oz)
Enclosure
Powder Coated Aluminum
USER INTERFACE
LED Indicators
READY, RF, COM
* When all connectors and antenna are correctly installed.
The BIS U-620-068-1x1-00-Sx Processor and its antenna
are intended for indoor use only.
GENERAL VIEW
LED INDICATORS
green
READY
The READY LED is ON after the power
up sequence has completed.
amber
RF
The RF LED illuminates when RF
power is being transmitted by the
antenna.
amber
COM
The COM (communications) LED
flashes ON and OFF when data is
being transmitted between the antenna
and a tag.
When in Continuous Read mode, the
COM LED will remain ON and will turn
OFF briefly only while data is being
read from or written to a tag.
CONNECTIVITY
M12 8 pin Male Connector (Data and Power Supply)
Typical Layout
See the BIS U-62_ Processor Manual for a complete list of accessories including
alternative cables and connectors.
DIGITAL I/O (-12 MODELS)
DIMENSIONS
M12 8-pin Female Connector (Digital I/O)
This connector is available on models
BIS U-620-068-1x1-00-S29.
See the BIS U-62_ Processor Manual for details
INSTALLATION GUIDELINES
• RF performance and read/write range can be negatively
impacted by the proximity of metallic objects and liquids.
Avoid mounting the BIS U-3x… antenna within 15 cm (6
inches) of any metallic object or wet surface.
• Do not route cables near other unshielded cables or
near wiring carrying high voltage or high current. Cross
cables at perpendicular intersections and avoid routing
cables near motors and solenoids.
• Avoid mounting the Processor near sources of EMI
(electro-magnetic interference) or near devices that
generate high ESD (electro-static discharge) levels.
Always use adequate ESD prevention measures to
dissipate potentially high voltages.
• If electrical interference is encountered (as indicated by
a significant reduction in read/write performance),
relocate the Processor to an area free from potential
sources of interference.
INSTALLATION
The BIS U-620-068-1x1-00-Sx RFID Processor is designed
for point-to-point RFID applications, where the distance from
host to Processor is less than 15 meters (50 feet). The
Processor connects directly to a serial communications port
on a host computer via an RS232-compatible serial
interface cable.
1. Select a suitable location for the BIS U-62… Processor
and BIS U-30… Antenna.
2. Mount the BIS U-30… Antenna (within the cable
distance of the Processor) and attach the BIS U-30…
Antenna cable as described in the installation guide
included with the antenna.
3. Fasten the Processor to your mounting fixture using two
M5 (#10) diameter screws (not included) and secure
them with appropriate washers and nuts. Tighten
screws to 1.7 Nm or 15 lbs per inch ± 10%. Connect
the antenna cable to the UHF Processor.
4. Connect the BCC0ETJM12 8-pin female connector to
the M12 8-pin male interface connector on the BIS U-
620-068-1x1-00-Sx Processor. Connect the
BCC0ETJ9-pin female D-sub connector to an RS232
COM port on the host computer. Tighten the cable’s
two locking thumbscrews.
5. Connect the power supply to the VDC (red) and GND
(black) wires on the BCC0ETJcable.
6. Apply power to the Processor after all cable
connections have been made. The LEDs on the unit will
flash. The READY LED is ON after the power up
sequence has completed.
7. On the host computer, set the COM port parameters to:
9600 baud, 8 data bits, 1 stop bit, no parity and no
handshaking.
To verify operations, download the Balluff Dashboard™
Configuration Tool from
www.balluff.com. The Balluff
Dashboard™ Configuration Tool allows users to configure
and control their BIS U-620-068-1x1-00-Sx Processors and
send RFID commands for testing purposes.
BIS U-620-068-1x1-
BCC0ETJ
Host
Power
Supply
BIS U-30x… antenna
Vdc (red)
GND (black)
mm
in
* Digital I/O (-ST29 models only)
*
*
*
zur Prüfung