Double Cylinder Handleset Installation Guide

ManualsBrandsBaldwin ManualsHandlesetNapa SmartKey Double Cylinder Keyed Entry Handleset with Traditional Square Rose and Round Knob on Interior

Double Cylinder Handleset Installation Instructions

Fits 1-3/4" (44 mm) up to 2" (51 mm) doors

(Thick door service kits for

2" (51 mm) up to 2-1/2" (64 mm) doors

available through customer service)

1-3/4"

(44 mm)

(51 mm)

2-1/4"

(57 mm)

2-1/2"

(64 mm)

Centerline

Ligne médiane

Linea central

2-3/8" 60mm

2-3/4" 70mm

2-3/8" 60mm

2-3/4" 70mm

1-3/4"

(44 mm)

(51 mm)

2-1/4"

(57 mm)

2-1/2"

(64 mm)

Centerline

Ligne médiane

Linea central

Fold

Doble

Plier

Fold

Doble

Plier

5-1/2" 140mm 8-13/32" 214mm

www.baldwinhardware.com • Customer Service 1.800.437.7448

TEMPLATE

Door Preparation

If your door requires drilling, use the supplied template below with the door preparation

instructions available at www.baldwinhardware.com

WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock

may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.

No lock can substitute for caution, awareness of your environment, and common sense. Builder’s

hardware is available in multiple performance grades to suit the application. In order to enhance

security and reduce risk, you should consult a qualied locksmith or other security professional.

1. Adjust and install latches

Measure your door and prepare using template if needed.

LATCH ASSEMBLY AND INSTALLATION

Handleset Latch

Drive in with hammer.

Snap on collar.

For Square Corner/Round Corner

For Drive-In Latch

If backset of door measures 2 3/4" (70mm),

adjust latch

shown by grasping the spring pin

and moving it to the 2-3/4” slot.

Install with 1/2" (3 mm) screws.

Snap together front and back plate.

Make sure the slant of latch bolt faces

in the direction that the door closes.

LATCH FACE ASSEMBLY

Remove backplate.

Snap on collar.

For Drive-In Latch

LATCH INSTALLATION

Deadbolt Latch

Install with 1/2" (13 mm) screws.

Drive in with hammer.

For Square Corner/

Round Corner

For Drive-In Latch

Ensure the latch is inserted

with the word “UP” on top.

Note, for a 1-1/2" (38 mm) diameter

hole, test if latch extends and retracts.

Chisel out area if required.

If backset of door

measures 2 3/4"

(70mm), adjust

latch by rotating

face as shown.

Make sure the curve of half round

spindle corresponds to the opening

in the latch; if it does not, reverse the

handing as follows: (1) Pull spindle

away from mechanism, (2) rotate it

1/2 turn (180°) and release.

(2)

(1)

Spindle

2. Measure door thickness

3. Install trim

• If door measures 1-3/4" (44 mm): Use shorter deadbolt

mounting screws in Step 3.

• If door measures between 1-3/4" (44 mm) and 2" (51mm):

Use longer torque blade supplied in the box. See illustrations in

Thick Door Installation Instructions below to replace the torque

blade. After torque blade replacement, proceed to Step 3 and

install deadbolt with longer mounting screws supplied in the box.

• If door is thicker than 2" (51 mm): See Thick Door Installation

Instructions below.

See drilling template for hole location.

Please note: Product

illustrations may differ

from your product.

Installation is the same.

Torque

Blade

deadbolt

interior

cylinder

deadbolt

mounting

screws

chassis

interior

trim

Only use if included in the box. Not used

with SmartKey products.

THICK DOOR KIT INSTALLATION INSTRUCTIONS (AVAILABLE SEPARATELY)

Supports 2" (51 mm) up to 2-1/2" (64 mm) doors

47066 / 02

5. Install strike

4. Install knob / lever

Place lever or knob onto chassis and turn set screw clockwise to secure.

The set screws are pre-installed.

They do not need to be removed

prior to knob/lever installation.

Adjust tang as needed.

1/8" (3 mm) pilot holes

may be required.

After the completion of Step 1, replace the existing cylinder torque blade with the longer torque blade

supplied in the kit. Next, replace the handleset spindle mechanism with the one supplied in the kit. Proceed

to Step 3 and install deadbolt interior cylinder and chassis interior trim with longer screws. During Step 5,

install strike supplied in the kit.

Install longer torque blade and

reinstall clip to secure.

Remove clip and torque blade.

Remove and

replace spindle

mechanism

Align pin

Do not distort clip.

Ensure clip ts tightly.

Do not

overtighten

screws.

25mm

Measure

after printing.

Mesurer après

imprimer.

Medida después

de la impresión.

The drilling template must be printed

to scale to ensure correct hole

placement. To conﬁrm correct print

scale, the square below must measure

exactly 1" by 1" (25mm x 25mm).

Le gabarit de perçage doit être

imprimé à l’échelle pour assurer le

placement correct des trous. Aﬁn de

conﬁrmer que l’échelle soit correcte,

le carré ci-dessous doit mesurer

exactement 1" x 1" (25mm x 25mm).

La plantilla de perforación deben estar

impresos a escala para conﬁrmar la

correcta colocación de los agujeros.

Con el ﬁn de conﬁrmar que la escala

de impresión es correcta, el cuadrado

de abajo debe medir exactamente

1" x 1" (25mm x 25mm).

Summary of content (2 pages)

PAGE 1
Double Cylinder Handleset Installation Instructions Fits 1-3/4" (44 mm) up to 2" (51 mm) doors (Thick door service kits for 2" (51 mm) up to 2-1/2" (64 mm) doors available through customer service) www.baldwinhardware.com • Customer Service 1.800.437.7448 1. Adjust and install latches Door Preparation If your door requires drilling, use the supplied template below with the door preparation instructions available at www.baldwinhardware.com Measure your door and prepare using template if needed.
PAGE 2
Instructions d’installations de l’ensemble serrure à double cylindre Instrucciones para la instalación del juego de manija de doble cilindro S’ajuste sur des portes de 1-3/4" (44 mm) jusqu’à 2" (51 mm) Para puertas de 1-3/4" (44 mm) a 2" (51 mm) (On peut se procurer des trousses de service pour portes d’une épaisseur de 2" (51 mm) à 2-1/2" (64 mm) auprès du service à la clientèle) (El servicio al cliente tiene juegos de reparación para puertas gruesas de 2" (51 mm) a 2-1/2" (64 mm) www.baldwinhardware.