Installation Sheet

ManualsBrandsBaldwin ManualsHandlesetSoho Full Dummy Two Point Sectional Handleset with the Right Handed Soho Interior Lever

H1705.000.00015A

2-POINT TUBULAR LOCK

INSTALLATION INSTRUCTIONS

TOOLS REQUIRED

1. Pencil

2. No. 2 and No. 3 Phillips Head Screwdrivers

3. No. 1 and No. 2 Slotted Screw Drivers

4. 1/8" Allen Head Wrench

5. 3/4" Wood Chisel or Corner Chisel

6. Measuring Device

7. Lock Face Template

8. Combination Square

9. Awl

10. Drill & Assorted Bits: 1/8", 5/32", 3/4", 1", 2-1/8"

11. Screw Wax or Soap

12. Powdered Chalk or Graphite

NOTE: In order to successfully install a tubular lock and trim, a minimum of average skill level is required with use of the

above listed tools. Backset is located from low side of beveled door, please adjust accordingly for non-beveled doors.

Read and understand the provided instructions BEFORE attempting to mark or cut the door and/or frame. If there are any

questions before you begin installation, phone or visit your nearest Baldwin Distributor or contact the Technical Service

Department at Baldwin at 1-800-437-7448.

INSIDE

Diagram A

OUTSIDE

THRU-

BOLTING

Fasteners

#10-32 x 2-5/8” PAN

HEAD SCREW

SCREW

BASE

LATCH

ASSEMBLY

DEADBOLT

ASSEMBLY

INTERIOR

SUBASSEMBLY

EXTERIOR

SUBASSEMBLY

DEADBOLT

CYLINDER

BACKPLATE

CYLINDER

SCREWS

Thru-bolting shown is for 1-3/4"

to 2” thick doors

CYLINDER

RING

CYLINDER

COLLAR

TURNPIECE

MOUNTING

SCREWS

KNOB

LEVER

***

THIMBLE

MOUNTING

SCREWS

SET SCREW

SCREW

COVER

THRU-

BOLTING

DOOR PULL

#8-32 x 3/4" FLAT

HEAD

COMBINATION

SCREW

#10-32 x 2-1/2” FLAT

HEAD SCREW

#10-32 x 1-1/4” FLAT

HEAD SCREW

#8-32 x 3/4”

OVAL HEAD

SCREW

#6-32 x 7/16”

OVAL HEAD

SCREW

SHOWN ACTUAL SIZE

*** MAY COME PREASSEMBLED

WAVE

WASHER

STYLE SHOWN

ASHTON

LANDON

Summary of content (4 pages)

PAGE 1
2-POINT TUBULAR LOCK INSTALLATION INSTRUCTIONS TOOLS REQUIRED 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Pencil No. 2 and No. 3 Phillips Head Screwdrivers No. 1 and No.
PAGE 2
DETERMINE HOLE LOCATIONS & MARK THE DOOR 1 A 2.50” B DRILL 2 POINT LOCK & DEADBOLT HOLES 2 For non-prepped doors: Mark the door at 38" above finished floor. Fold the paper template and tape in place at the centerline of the lower 2-1/8" hole (C). Determine / Mark the backset & all other hole locations per the purchased style.
PAGE 3
10 INSTALL EXTERIOR ASSEMBLY 11 INSTALL SCREWS 12 CHECK ALIGNMENT & TEST OPERATION Check alignment of exterior assembly with door edge. #10-32 X 1-1/4” SCREWS WAVE WASHER TAB FOR THUMBPIECE ENGAGEMENT Install exterior assembly. A) Turn tailpiece vertical B) Insert cylinder tailpiece into spindle C) Align screw posts with interior mechanism body. D) Engage thumbpiece with interior mechanism. Thumbpiece arm must be under tab of interior mechanism.
PAGE 4
STRIKE PLATE INSTALLATION 19 20 DRILL HOLES & SCORE STRIKE PLATE OUTLINES 21 CHISEL STRIKE PLATE CAVITIES MARK JAMB WITH STRIKE TEMPLATE * Apply any weatherstripping before installing strike(s). Mark deadbolt with chalk, lipstick or pencil. Shut door and throw deadbolt to transfer location to doorjamb. Using the supplied template, align strike hole template with center point. Mark center holes of latch bolt and outer corners of both strikes with a pencil.