Installation Guide

Strike Installation
Strike Installation
Congratulations!
Remember Baldwin
With your purchase of The Images Collection solid brass entrance lockset,
you’re among a group of discerning individuals who know the intrinsic
value of selecting the finest – Baldwin.
Images entrance locksets and interior latchsets coordinate beautifully,
enabling you to carry a specific design theme throughout your home.
Our step-by-step installation instructions will help guide you through your
project quickly and easily.
Before you begin your installation, read and understand the installation
instructions and marking templates. If you have any questions, please do
not hesitate to contact our Baldwin Technical Services Department,
1-800-566-1986. We’re here to help!
We thank you for your Baldwin purchase and wish you
the fullest enjoyment of your Baldwin Handleset.
With the completion of your
project, remember that
Baldwin quality hardware
and giftware products are
available for all your deco-
rating and remodeling
needs. Matching knob and
leversets for interior doors,
beautiful bath accessories,
and a complete selection of
cabinet and door enhancing
hardware are all available
from your Baldwin retailer.
1
Mark door frame using
strike marking template,
locate and mark strike
mounting screws and
centering points for both
strikes at required door
thickness.
2
Align and trace the outline of
strikes onto the door frame
using mounting screw marks
for location.
3
For Deadbolt Strike: Using reinforcing
strike as a template, mark locations for
reinforcing screws (fig. 1). Drill two 5/32"
dia. pilot holes for the 3" long screws
and two 1/8" dia. pilot holes for the #8 x
3/4" screws. Mark drill points 5/16"
above and below centering point. Bore
two 1" dia. holes 1-1/4" deep at these
points. Chisel out holes for dust box.
For Latch Strike: At previously marked
locations, drill two 1/8" dia. pilot holes
for the #8 x 3/4" screws. Mark drill
points 5/16" above and below centering
point. Bore two 1" dia. holes x 1" deep at
these points. Chisel out holes for dust
box.
4
For Deadbolt Strike , mortise 7/32" deep
or until the strike box, reinforcing strike
and strike plate fits inside mortise and
flush with the door frame.
For Latch Strike, mortise 3/32" deep
or until strike box
and strike fit inside
mortise and flush
with the door
frame.
5
Installation: Install strike as illustrated.
Bore 1" dia. hole
above and below
centering point.
Bore 1" dia. hole
above and below
centering point.
Drill 1/8" dia. pilot
holes for No. 8
screws.
Drill 1/8" dia. pilot holes
for No. 8 screws.
Drill 5/32" dia.
pilot holes for
3" long screws.
5/16" above center point.
5/16" below center point.
5/16" above center point.
5/16" below center point.
1. Dust box (deadbolt)
2. Reinforcing strike
3. #8 x 3/4" combination screws (2)
4. 3" reinforcing screws* (2)
5. Strike plate (deadbolt)
6. #8-32 x 1/4" machine screws (2)
7. Dust box (latch)
8. Strike (latch)
9. #8 x 3/4" wood screws (2)
*Note:
Lubricant recommended
when installing 3" reinforcing
screws.
©Baldwin Hardware Corporation
P.O. Box 15048 Reading, PA 19612
Entrance
Escutcheon Handleset
Installation Instructions
Fig. 1
1.
Deadbolt
Latchbolt
2.
4.
6.
5.
9.
8.
7.
3.
.
B
a
l
d
w
i
n
.
G
u
a
r
a
n
t
e
e
d
F
o
r
L
i
fe
.
PK-1084 (8/98)
®
BALDWIN
®
Technical Services Support
1-800-566-1986
Hours: 6 am to Midnight C.S.T.-7days a week.
Door Preparation
Door Preparation Single Cylinder and Double Cylinder
Door Preparation/Dummy Handleset
1
To position template fold enclosed tem-
plate on line and locate on door at speci-
fied height. If door is beveled, place fold-
ed edge on low side of bevel as shown in
illustration. If you have a new door that is
not already cut-out, please follow instruc-
tions for non-bored doors. If your door is
pre-bored, please follow instructions for
bored doors below.
Non-bored doors – Determine door
thickness and type of handleset to be
installed. Locate and mark required holes
(A, B, C, D,E) for drilling, as per enclosed
marking template. Proceed to Step 2.
Bored doors – Mark and drill hole E
(5/16") for appropriate handleset design.
Now proceed to handleset installation
instructions on reverse side Step 1.
2
Drill the 2-1/8” diameter face bores (A and B) through
the door and 1” diameter edge bores (C and D) 3-1/2”
deep for 2-3/8” backset or 3-7/8” deep for 2-3/4”
backset. The latch and deadbolt accomodates both
size backsets. Drill the 5/16” lower pull assembly hole
(E) for the appropriate handleset shown on template.
Drill a 2-1/8” diameter face bore (A). Drill the 1/2” dummy
cylinder hole (B) through the door. Drill the 5/16” lower pull
assembly hole (C) for the appropriate handleset shown
on template.
4
Chisel out area marked in
step 3 to a depth of 5/32"
or until faceplate is flush
with door edge.
3
Insert deadbolt into edge of door. While
holding faceplate parallel to edge of door,
trace an outline of the faceplate ontothe
door edge.Mark screwhole centers and
drill. Remove deadbolt and repeat process
for latch.
2
Caution: Re-check hole locations before drilling.
A - 2-1/8"
B - 1/2"
C - 5/16" Drill for proper handleset
1
To position template fold enclosed template on line and locate on door
at specified height. If door is beveled, place folded edge on low side of
bevel as shown in illustration. If you have a new door that is not already
cut-out, please follow instructions for non-bored doors. If your door is
pre-bored, please follow instructions for bored doors below.
Non-bored doors – Determine door thickness and type of handleset to
be installed. Measure height and backset of active trim, using enclosed
marking template to locate and mark required holes (A,B,C) for drilling.
Insure that backset and height match active trim. Proceed to Step 2
Bored doors – Mark and drill hole C (5/16") for appropriate handleset
design. Now proceed to handleset installation instructions Step 1 on
reverse side.
INSIDE
Template
Top view of door
Template
Top view of door
A
A
A
A
B
C
E
E
B
B
BC
C
C
D
D
Caution: Re-check
hole locations
before drilling.
A - 2-1/8"
B - 2-1/8”
C - 1"
D - 1"
E - 5/16" Drill for proper
handleset.
TEAR HERE FOR ENGLISH. TEAR HERE FOR ENGLISH.TEAR HERE FOR ENGLISH.
PK-1084 (8/98)