Installation Guide
Handleset Trim Installation: Single Cylinder & Double Cylinder
From inside of door insert short end of spin-
dle through the latch with the “V” groove
angled down and toward the hinges. Align
outside handle on the door and install, so the
spindle slides into the thumbpiece cartridge.
Installing Deadbolt and Latch
Installing Outside Trim
Exploded View Dummy Handleset
1
1
2
3
4
Installing Inside Knob
5
6
7
8
a. The latch and deadbolt supplied with this unit has an adjustable back-
set feature. It will be set at 2-3/8” backset. To adjust to 2-3/4” backset,
grasp body and twist faceplate/bolthead assembly 180˚
until it stops. Latch or deadbolt is now ready for installation in 2-3/4”
backset configuration.
b. Insert deadbolt and latch. Install with four #8 x 3/4" flat head combina-
tion screws provided (see diagram for proper positioning). Insure dead-
bolthead is extended throughout installation procedure.
INSIDE
INSIDE
INSIDE
Installing Turnpiece Trim
Place turnpiece trim over
mounting plate. Insert cylin-
der tailpiece into turn piece
trim. Attach turn piece to
mounting plate with two
#8-32 x 5/8" oval head
machine screws. (fig. 5)
Slip spindle collar onto spindle
with groove in collar toward the
short end of the spindle.
Carefully break off cylinder tail-
piece at required mark for your
door thickness.
Align tailpiece with slot. Keep
tailpiece vertical and curved
towards right side of the hole as
illustrated.
Hold outside handle assembly in place. Attach adaptor with
the short #10-32 x 2-1/8" truss head screw in the top hole
and the long #10-32 x 2-5/8" truss head screw in the bottom
hole. To secure bottom of outside handle, insert the #10-32
x 2-1/2" flat head machine screw through the screw cover
backplate. Screw through door and into bottom of outside
handle. Tighten all screws.
Snap rosette onto the adap-
tor. Pull spindle out as far as
possible and depress thumb-
piece. With thumbpiece
depressed slide knob onto
spindle and tighten set (with
allen wrench supplied)
screw into “V” groove.
Screw on decorative screw
cover.
Congratulations!
Your installation is now
complete.
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
Align outside handle with
door borings as shown.
Place dummy cylinder in
cylinder hole of outside han-
dle. Insert truss head screws
through screw cover back-
plates and attach pull
assembly to door (use #8-32
x 2-1/4" flat head screw in
top; #10-32 x 2-1/2" flat
head screw in bottom. Do
not tighten screws.
2
Attach inside adaptor to
outside handle with the
short #10-32 x 2-1/8" truss
head screw in the top hole
and #10-32 x 2-5/8" truss
head screw in the bottom
hole. Tighten all screws.
3
Snap rosette onto adap-
tor. Slide knob onto spin-
dle and tighten set screw.
Attach screw covers.
Congratulations!
Your installation is
now complete!
Install deadbolt with both long slots
on latch body in upper position.
Latch
Extended Bolt
Head
Rotate latch if necessary
(angle of Latchbolt should
face door jamb.)
Thumbpiece
Thumbpiece
Cartridge
Pull
Assembly
Adaptor
Dummy
Cylinder
Outside
Handle
Adaptor
Screw cover
Adaptor
Spindle
Rosette
Set Screw
Screw Cover
Screw Cover
Backplate
Screw Cover
Backplate
Screw Cover
Backplate
10-32 x 2-1/2”
Flat Head Screw
10-32 x 2-5/8”
Truss Head Screw
10-32 x 2-1/8”
Truss Head Screw
Short
End of Spindle
“V” Groove
Tailpiece
Cylinder
fig. 5
Spindle
Adaptor
Rosette
Set Screw
Screw Cover
Mounting Plate
Turnpiece Trim
Tailpiece
Cylinder
Slot
2-1/4"
2"
1-3/4""
Double Cylinder Assembly Single Cylinder Assembly
7
8
5
6
Single Cylinder Assembly Outside (fig. 3)
Extend deadbolt using flat head screwdriver.
Keeping tailpiece vertical, insert cylinder
through escutcheon plate and into deadbolt.
Hold in place. Do not insert key during this
procedure.
Single Cylinder Assembly Inside
Place turnpiece mounting plate on inside of
door as shown. Attach cylinder using two
#10-32 x 1-7/8" pan head machine screws.
Tighten all screws. (fig. 4)
OUTSIDE
OUTSIDE
INSIDE
Escutcheon
fig. 3
fig. 1
fig. 4
Cylinder
Cylinder
Cylinder
Threaded Collar
Extended Deadbolt
Extended
Deadbolt
Mounting Plate
Double Cylinder Assembly Outside (fig. 1)
Extend deadbolt using flat head screwdriver. Keeping tailpiece
vertical and toward the right side of the hole, insert outside cylin-
der through escutcheon and into the deadbolt. Align slot of inside
cylinder with notch in threaded collar. Keeping tailpiece vertical
and curved toward the right, insert cylinder with threaded collar
into the deadbolt. Attach cylinders using two #10-32 x 2-1/4" flat
head machine screws. Tighten screws. Do not insert key during
this procedure.
Double Cylinder Assembly Inside
Align cylinder cover over inside cylinder. Screw on decora-
tive cylinder collar. Proceed to Step 9. (fig. 2)
INSIDE
fig. 2
Inside Cylinder
Cylinder Cover
Cylinder Collar
10-32 x 2 1/8”
Truss Head
Screw
10-32 x 2 5/8”
Truss Head Screw
Parts Enclosed:
Installation
1. 2 ea. Screw Covers
2. 1 #10-32 x 2-1/2” Flat Head Machine Screw
3. 2 ea. Screw Cover Backplates
4. 1 Set Screw
5. 1 Knob
6. 1 Rosette
7. 1 #10-32 x 2-1/8” Truss Head Screw
8. 1 #10-32 x 2-5/8” Truss Head Screw
9. 1 Adaptor
10. 1 Outside Handle
11. 1 Dummy Cylinder
12. 1 #8-32 x 2- 1/4” Flat Head Machine
Screw
13. 1 Allen Wrench (not shown)
1.
4.
6.
7.
9.
3.
12.
1.
8.
10.
11.
5.
2.
3.
Exploded View Single Cylinder Handleset
Parts Enclosed:
Tools Needed: Only Required for Doors Without Cutout
Tools Needed: Trim Installation for Doors with 2-1/8” Cutouts
Exploded View Double Cylinder Handleset
1. 1 Screw Cover
2. 1 #10-32 x 2-1/2” Flat Head
Machine Screw
3. 1 Screw Cover Backplate
4. 1 Set Screw
5. 1 Knob
6. 1 Rosette
7. 1 #10-32 x 2-1/8” Truss Head Screw
8. 1 #10-32 x 2-5/8” Truss Head Screw
9. 1 Adaptor
10. 1 Spindle Assembly
1. Pencil
2. Measuring Device
3. Hole Saw, 2-1/8” diameter (required when door is not prepared)
4. 1/2” and 3/4” Wood Chisel
5. Drill and Assorted Bits: 1/8”, 5/32”, 1/2” (required for FD trim only) and 1”.
1. Measuring Device
2. Two Pairs of Pliers
3. No. 2 and No. 3 Phillips Screwdrivers
4. Allen Wrenches (supplied)
5. Flat Head Screwdriver
Parts Enclosed:
11. 4 each #8 x 3/4” Flat Head Combination Screws
12. 1 Adjustable Backset Latch
13. 1 Adjustable Backset Deadbolt
14. 1 Outside Handle
15. 1 Outside Cylinder
16. 1 Threaded Collar
17. 1 Inside Cylinder
18. 2 each #10-32 x 2-1/4” Flat Head Machine Screw
19. 1 Cylinder Cover
20. 1 Cylinder Collar
21. 1 Allen Wrench (not shown)
11. 4 each #8 x 3/4” Flat Head
Combination Screws
12. 1 Adjustable Backset Latch
13. 1 Adjustable Backset Deadbolt
14. 1 Outside Handle
15. 1 Outside Cylinder
16. 1 Turnpiece Mounting Plate
17. 2 each #10-32 x 1-7/8” Pan Head
Machine Screws
18. 1 Turnpiece Trim
19. 2 each #8-32 x 5/8” Oval Head
Machine Screws
20. 1 Allen Wrench (not shown)
Note: See Strike Installation section
for strike parts listing.
Note: See Strike Installation
Section for strike parts listing.
1. 1 Screw Cover
2. 1 #10-32 x 2-1/2” Flat Head Machine Screw
3. 1 Screw Cover Backplate
4. 1 Set Screw
5. 1 Knob
6. 1 Rosette
7. 1 #10-32 x 2-1/8” Truss Head Screw
8. 1 #10-32 x 2-5/8” Truss Head Screw
9. 1 Adaptor
10. 1 Spindle Assembly
1.
1.
2.
3.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
14.
15.
17.
16.
18.
19.
12.
15.
14.
13.
12.
13.
10.
16.
17.
19.
20.
18.
6.
7.
8.
9.
4.
5.
11.
Handleset Trim Installation: Dummy
10-32 x 2 5/8” bolt
must be installed
on bottom
STOP
TEAR HERE FOR ENGLISH. TEAR HERE FOR ENGLISH.TEAR HERE FOR ENGLISH.