Installation Guide

To position template fold enclosed template on line
and locate on door at specified height (about 45” from
the floor or 5-1/2” above center of existing latchset). If
you have a new door that is not already cut-out, please
follow these instructions. If your door is pre-bored
please proceed to Single Cylinder & Double Cylinder
Deadbolt Installation-Step 1. If the door is beveled,
place the folded edge on low side of bevel as shown in
the illustration. Determine door thickness and backset
(2-3/8” or 2-3/4”). Mark the door for face and edge
bores.
Deadbolt Installation/Single Cylinder and Double Cylinder
Tools Needed: Only Required for Doors Without Cutout
Tools Needed: Doors Prepared with 2-1/8” Cutout
Optional Deadbolt Accessories for 1-3/8” Doors
Exploded View Single Cylinder Deadbolt
Exploded View Double Cylinder Deadbolt
Parts Enclosed
If your door is not pre-bored, see reverse side of instructions
for door preparation.
1. Pencil 3. 1/2” or 3/4” wood chisel
2. 2-1/8” diameter hole saw 4. Drill and assorted bits: 1/8”, 5/32” and 1”
When installing deadbolts on 1-3/8” thick doors, optional Cylinder Collar
Spacers are required (No. 8297). Consult your Baldwin distributor for
further details.
6.
5.
7.
8.
4.
3.
2.
1. 2 each #8 - 32 Oval Head
Machine Screw
2. 1 Turnpiece Trim
3. 2 each #10 -32x 1-7/8” Pan Head
Machine Screw
4. 1 Turnpiece Mounting Plate
Parts Enclosed
1. 1 Inside Cylinder Collar
2. 1 Cylinder Cover
3. 2 each #10 -32x2-1/4” Flat Head
Machine Screws
4. 1 Inside Cylinder
5. 1 Threaded Collar
6.
3.
1.
2.
4.
5.
8.
9.
7.
Note: See Strike Installation section for strike parts listing.
Note: See Strike Installation section for strike parts listing.
5. 1 Adjustable Backset Deadbolt
6. 4 each #8 x 3/4” Flathead
Combination Screws
7. 1 Outside Cylinder Collar
8. 1 Outside Cylinder
9. Screw Guide
6. 1 Adjustable Backset Deadbolt
7. 4 each #8 x 3/4” Flathead
Combination Screws
8. 1 Outside Cylinder Collar
9. 1 Outside Cylinder
10. Screw Guide
1. No. 2 and No. 3 phillips screwdrivers 3. Two pliers for Double Cylinder
2. Measuring device 4. Flathead Screwdriver
Strike Installation
Close door and
extend deadbolt
several times
against door frame.
Strike centering
indicator will leave a
center mark on the
door frame. (Fig. 1)
1
1
2 4
Chisel out the area marked for the face-
plate to a depth of 5/32” or until faceplate
is flush with door edge. Proceed now to
the Strike Installation.
3
Insert deadbolt into edge of door while
holding faceplate.Trace the outline of
the faceplate onto the door edge. Mark
screw hole centers and drill with a
1/8”drill.
Drill the 2-1/8” diameter face bore (A)
through the door and 1” diameter edge
bore (B) 3-1/2” deep for a 2-3/8” backset
or 3-7/8” deep for a 2-3/4” backset. The bolt
accommodates both size backsets.
Caution: Re-check hole locations
before drilling.
Using reinforcing strike as
a template, mark locations
for reinforcing screws. (Fig
3) Drill two 5/32” dia. pilot
holes for the 3” long screws
and two 1/8” dia. pilot holes
for the #8 x 3/4” screws.
Mark drill points 5/16”
above and below centering
point. Bore two 1” dia. holes
1-1/4” deep at these points.
Chisel out holes for dust
box. (Fig. 4)
2
Position strike plate
on center mark.
Align and trace
outside of strike and
mounting screws
onto the door frame.
(Fig. 2)
3
Mortise 7/32” deep or
until the strike box, rein-
forcing strike and strike
plate fits inside mortise
and flushwith the door
frame. (Fig. 5)
4
5
Install strike as
illustrated.
center line
Top view of door
Template
Facebore
Edgebore
Centering
indicator
Bore 1” dia. hole
above and below
centering point.
Drill 1/8” dia. pilot
holes for # 8 screws.
Drill 5/32” dia. pilot
holes for 3” screws.
5/16” above
center point.
5/16” below center point.
Fig. 4
Fig. 3
Fig. 5
A
A
B
B
Door Preparation
Fig.1
Fig. 2
1. Dust Box
2. Reinforcing Strike
3. #8 x 3/4” Combination
6. Screws (2)
4. 3” Reinforcing
6. Screws* (2)
5. Strike Plate
6. #8-32 x 1/4”
6. Machine Screws (2)
* Note: Lubricant
recommended when
installing 3” reinforcing
screws.
1
2
4*
6
5
3
TEAR HERE FOR ENGLISH. TEAR HERE FOR ENGLISH.
9. Note: Component 9 not included
with all product.
10. Note: Component 10 not included with all product.