Installation Guide

INSIDE
Cylinder collar
Cylinder cover
Inside Cylinder
2-1/8” Deadbolt Preparation
PK-1152-T (8/00)
©Baldwin Hardware Corporation
P.O. Box 15048 Reading, PA 19612
b. Place turnpiece mounting plate on inside of
door as shown. The side with "TOP" marked on
plate should be against the door. Attach
cylinder using two #10-32 x 1-7/8" pan head
machine screws. Insert screws through
mounting plate, deadbolt, screw guide and col-
lar into the cylinder. Tighten all screws. (fig. 2)
Installing Deadbolt
1
Single Cylinder Assembly
1
2
Double Cylinder Assembly
1
a. Extend deadbolt using flathead screw-
driver. Keeping tailpiece vertical, insert
cylinder through collar and screw guide
into deadbolt. The arrow on the screw
guide must be on the outside and point-
ing up. Hold in place. Do not insert key
during this procedure. (fig. 1)
b. Insert deadbolt. Install with two #8 x 3/4" flat
head combination screws provided (see diagram
for proper positioning). Ensure deadbolt head is
extended throughout installation procedure.
a.The deadbolt sup-
plied with this unit
has an adjustable
backset feature. It will
be set at 2-3/8" back-
set. To adjust to
2-3/4" backset, grasp
body and twist face-
plate/bolthead assembly 180° until it stops.
Unit is now ready for installation in a 2-3/4"
backset configuration.
a. Carefully break off cylinder
tailpiece at required mark for
your door thickness.
Caution; use two pairs of
pliers as shown or tail-
piece will be damaged.
b. Align tailpiece with
slot. Keep tailpiece verti-
cal and curved toward
right side of the hole as
illustrated.
c. Place turnpiece trim over mounting plate. Insert
tailpiece into turn piece. Attach trim to mounting plate
with two #8-32 x 5/8" oval head machine screws.
Tighten screws. (fig 3)
a. Extend deadbolt
using flathead
screwdriver.
Keeping tailpiece
vertical and
toward the right
side of hole, insert
outside cylinder
through collar,
screw guide, then-
into the deadbolt. Align slot of inside cylinder with notch in
threaded collar. Keeping tailpiece vertical and curved toward
the right side of hole, insert inside cylinder with threaded collar
into the deadbolt. Attach cylinders using two #10-32 x 2-1/4"
flat head machine screws. Tighten screws. Do not insert key
during this procedure. (fig.4)
b. Align cylinder cover
over inside cylinder.
Screw on decorative
cylinder collar.
Congratulations! Your
installation is now
complete!
Collar
Cylinder
Extended deadbolt
Tailpiece
1-3/4"
2-1/4"
2"
Tailpiece
OUTSIDE
Mounting plate
INSIDE
INSIDE
INSIDE
Mounting plate
Turnpiece trim
fig. 3
Install deadbolt with both long
slots on latch body in upper
position.
Cylinder
Cylinder
Slot
Remember Baldwin
With the completion of your
project, remember that
Baldwin quality hardware
and giftware products are
available for all your deco-
rating and remodeling
needs. Matching knob and
leversets for interior doors,
beautiful bath accessories,
and a complete selection of
cabinet and door enhancing
hardware are all available
from your Baldwin retailer.
With your purchase of The Images Collection solid brass deadbolt, you’re
among a group of discerning individuals who know the intrinsic value of
selecting the finest – Baldwin.
Images entrance locksets, interior latchsets, and deadbolts coordinate beautifully,
enabling you to carry a specific design theme throughout your home.
Our step-by-step installation instructions will help guide you through your
project quickly and easily.
Before you begin your installation, read and understand the
installation instructions and marking templates. If you have any
questions, please do not hesitate to contact our Baldwin Technical Services
Department, 1-800-566-1986
. We’re here to help!
NOTE: Failure to use all recommended components will void Grade 1 rating.
We thank you for your Baldwin purchase and wish you the fullest
enjoyment of your Baldwin Handleset.
Technical Services Support
1-800-566-1986
Hours: 6 am to Midnight C.S.T.-7days a week.
(fig. 1)
(fig. 2)
Congratulations!
fig. 4
Outside Cylinder
Inside Cylinder
Threaded
collar
Extended
deadbolt
Collar
OUTSIDE
TEAR HERE FOR ENGLISH. TEAR HERE FOR ENGLISH.
PK-1152-T (8/00)
2-1/8” Collar
Auxiliary Deadbolt
Installation Instructions
BHMA
Screw
Guide
Screw
Guide