Installation Sheet

Installation Instructions
ENGLISH
Premium Entrance Set
FULL DUMMY
ESCUTCHEON TRIMS
PK.5706
Full Dummy Installation
3
3 If Full Dummy Trim will
be installed next to an active
door, height from bottom of
door and backset must match
the active door. Backset is the
distance from the edge of door
to center of hole (A), the 2
1
⁄8”
dia. hole. Otherwise, locate
center hole (A) 38” from floor.
Tape template to door.
4 Locate and mark positions
for (A, B, and C) on template.
5 Very carefully drill (A) 2
1
⁄8”
hole into one side of door face
until drill bit starts to protrude
on opposite side.
Important: Drill
perpendicularly (at a 90º
angle) to door.
6 Complete drilling hole (A)
from opposite side of door.
Drill (B)
1
⁄2” hole into door
exactly at pencil mark.
7 Very carefully drill (C)
5
⁄16” hole into door exactly at
pencil mark.
1 Measure the diameter of
top hole (B) in door. If hole is
2
1
⁄8”, orient the locating plate
as shown in Fig. 1. If hole is
less than 2
1
⁄8”, orient locating
plate as shown in Fig. 2.
2 Attach handleset by inserting
the #10-32 x 2
1
/
2
” flat head
screw on inside of door through
screw cover back plate and
lower hole (C). Leave screw
loose for adjustment. Insert
the dummy cylinder through
outside handleset and into door.
From inside, insert retaining
screw through lock washer and
locating plate. Screw into outside
dummy cylinder. Align handleset
on door and tighten screws.
4 Place the dummy inside
adapter on the door, aligning
the holes in adapter with post on
outside handle. Secure with two
#10-32 x 1
1
⁄4” truss head screws.
3 Place the dummy interior
top plate over locating plate and
fasten in place by inserting the
#8-32 x
5
⁄8” machine screw
though hole in center of trim.
1 Pull door toward you to
check if it’s level. Observe
contact of door to jam and
make sure it’s level. Adjust if
necessary.
Door Preparation (If Needed)
2
Before You Begin
1
• Remove and discard all materials and screw(s) used for packing
your Full Dummy Trim Set. Verify that you have all parts pictured on
exploded view section of instructions.
• Check the thickness of the door. This Full Dummy Trim Set works on
doors 1
3
⁄4” thick only. For doors greater than 1
3
⁄4” up to 2
1
⁄4” thick,
contact our Consumer Help Line at 1-800-566-1986. The conversion
kit part number for this item is 5399.XXX.D; please specify the finish of
your product.
• Follow the step-by-step sequence to ensure proper
operation of your Baldwin lockset.
• If your door is pre-drilled, see Full Dummy installation Step 1. If it is not
pre-drilled, see door preparation Step 1.
• We recommend spreading cardboard over floor to prevent scratching parts
and marring floor.
• Always wear protective eyewear.
Note: The illustrations in these instructions depict the outside handle
being installed on the right of the door. For installation of the outside
handle on the left of the door, proceed as if all illustrations were reversed.
PK.5706
12/11
5370
5375 5380
Exploded View
Outside Handleset
Trim
Screw Cover Backplate
#10-32 x 2
1
⁄2” Flat Head Screw
Screw Cover
Dummy Cylinder
#8-32 x
5
⁄8” Machine Screw
#10-32 x 1
1
⁄4” Truss Head Screws
Locating Plate
Set Screw
Lock Washer
Dummy Interior Top Plate
2” Retainer Screw
Dummy Inside Adapter
Allen Wrench
Nantucket
®
Glennon
™
hole template
low side of bevel
door stop
A
B=
1
⁄2”
A
C
top of door
Buckingham
®
2 (Aerial View) To ensure
proper alignment, only use
hole template on side facing
doorstop.
Helpful Hint: Some doors
have a beveled edge with bevel
facing doorstop.
inside
5 Use the rose retainer
wrench to attach the rosette
to the dummy inside adapter
with the rose retainer. Slide
knob/lever onto spindle and
tighten set screw with allen
wrench. Knob/lever is secured
when set screw enters V groove
in spindle. Attach bottom
screw cover.
inside
Rosette
Knob/Lever
Handleset Installation
Fasteners
Protective
Eyewear
Phillips
Screwdriver
Tape
Measure
Flat Head
Screwdriver
2
1
⁄8” Dia. Face
Bore Hole Saw
Electric
Drill
1
⁄2” Wood
Chisel
1
⁄8” Wood
Drill Bit
5
⁄16” Wood
Drill Bit
1
⁄2” Wood
Drill Bit
Pencil
Chalk,
Grease Pencil, or
Lipstick
Utility
Knife
Masking Tape 24” Level
Hammer
Helpful Tools
Wood Filler
Beeswax
or Soap
Required Tools
2” Retainer
Screw
(2) #10-32 x 1
1
⁄4”
Truss Head
Screws
#8-32 x
5
⁄8”
Machine Screw
#10-32 x 2
1
⁄2”
Flat Head Screw
Set Screw
insideinside
Fig. 1
Fig. 2
B
B
C
Post
post
1 If weather stripping is
not installed, you must
install weather stripping
prior to strikeplate
installation. Mark center
of deadbolt with chalk, grease
pencil, or lipstick. Shut door
and lock deadbolt to mark
center point on inactive door.
3 On inactive door, align
strike hole template with center
point. Mark holes for center of
latch bolt and outer corners of
both strikes with pencil.
4 For Deadbolt and Latch
Strikeplates: Mark drill
points
5
⁄16” above and below
center points. Bore two 1”
holes 1
1
⁄4” deep for deadbolt
dustbox and two 1” holes 1”
deep for latch dustbox. Score
chisel guide into door frame
with utility knife.
5 For Deadbolt and
Latch Strikeplates: Chisel
out holes for dustboxes.
Chisel out cavity so deadbolt
strikeplate and latch strikeplate
fit flush with doorframe.
For deadbolt strikeplate,
cavity is
7
⁄32” deep.
For latch strikeplate,
cavity is
3
⁄32” deep.
6 For Deadbolt Strikeplate:
Using reinforcing strikeplate as a
template, drill four
1
⁄8” pilot holes
for #8 x
3
⁄4” combination screws.
9 For Latch Strikeplate:
Using latch strikeplate as a
template, drill two
1
⁄8” pilot
holes for the
#8 x
3
⁄4” screws.
7 For Deadbolt Strikeplate:
Insert dustbox into hole, add
reinforcing strike, and secure with
four #8 x
3
⁄4” combination screws.
Two screws are supplied with active
trim and two are supplied with
dummy trim.
Important: Do not install
3” screws in double door
applications.
Helpful Hint: When installing
wood screws it is recommended
to put beeswax or soap on screw
threads to improve installation.
8 For Deadbolt
Strikeplate: Add strikeplate
and secure with #8-32 x
1
⁄4”
screws.
insideinside
inside
10 For Latch Strikeplate:
Insert dustbox into hole, add
strikeplate, and secure by
inserting #8 x
3
⁄4” wood screws
into pilot holes.
inside
inside
inside
inside
Troubleshooting Guide
If parts are missing do not return product. Please call Baldwin’s Consumer Help Line at 1-800-566-1986 and we will
quickly send the parts to you.
inside
4
For Double Door Installation Only
Strikeplate Installation for Inactive Door (Strikeplate Hardware is Shipped with Active Trim)
IMPORTANT! You must install Baldwin strikeplate or your warranty is void.
2 (Aerial View) Alignment
of Latch Strikeplate:
Curved edge of latch strikeplate
should face curved side of
latchbolt.
inside
1” Spade Bit or
1” Hole Saw
(Recommended)
Door Frame Template
Door Hole Template
(2) #8 x
3
⁄4”
Combination
Screws
Strikeplate
Installation
Fasteners
for Double
Door
Installation
Only
Congratulations!
With your purchase of this Premium Full Dummy Trim Set, you’re
among a group of discerning individuals who know the intrinsic value of
selecting the finest—Baldwin.
Our step-by-step installation instructions will help guide you through your
project quickly and easily.
Before you begin your installation, read and understand the installation
instructions and marking templates. If you have any questions, please
do not hesitate to contact our Baldwin Consumer Help Line at
1-800-566-1986. We’re here to help! We thank you for your purchase
and wish you the fullest enjoyment of your Baldwin product.
Care and Maintenance
WARNING: Do not attempt to clean your hardware with any type of
abrasive cleaners, solvents, or chemicals. These types of cleaning agents
may mar the finish. A damp cloth is all that is necessary to wipe clean.
Note: Finish Number 102, Oil-Rubbed Bronze, can be cleaned with light
machine oil and wiped with a dry cloth.
Consumer Help Line
1-800-566-1986
Hours: 8 a.m. to 8 p.m. E.S.T - Monday - Friday
10 a.m. to 6 p.m. E.S.T - Saturday
If you have trouble installing your Baldwin product, feel free to call our
toll-free Consumer Help Line.
www.baldwinhardware.com
©2011 Baldwin Hardware Corporation
19701 Da Vinci, Lake Forest, CA, 92610
Remember Baldwin
With the completion of your project, remember that Baldwin quality
hardware products are available for all your decorating and remodeling
needs. Matching entrance sets for exterior doors, beautiful bath
accessories, and a complete selection of cabinet and door-enhancing
hardware are all available from your Baldwin retailer.
To request a product brochure or the name of a retailer near you,
call 1-800-566-1986.
Baldwin offers a vast array of exceptional solid brass products to elegantly
enhance all areas of the home. Each collection features a wide variety of
beautiful, high-fashion finishes. From door hardware to bath accessories,
Baldwin provides the discriminating decorator with numerous options to accent
and complement the home’s ambience with distinction, taste, and fine detail.
Browse through the Baldwin Collection of beautiful locks, bath
accessories and decorative hardware. Compare styles and finishes.
There are thousands of photos and descriptions available to help
you coordinate hardware throughout your home. Create your ideal
“wish list” then visit your Baldwin Retailer or Dealer. Visit www.
baldwinhardware.com today!
Warranty Information
Limited Lifetime Mechanical Warranty – Baldwin warrants that
each Baldwin product shall be free from mechanical defects at the time of
delivery and for the lifetime of the product or as long as you own your home.
Limited Lifetime Finish
™
Warranty – The Baldwin Lifetime
Finish
™
uses advanced finishing technology (physical vapor deposition)
to create a finish highly resistant to the effects of weather and normal wear
and tear. The Limited Lifetime Finish Warranty on Lifetime Finish
™
products covers the original purchaser for as long as you own your home.
Limited Finish Warranty – The finish on Baldwin products (excluding
Lifetime Finish and living finish products) is protected by a durable topcoat
designed to maintain the beauty and quality of the Baldwin product. The
Baldwin Limited Finish Warranty covers the original purchaser for five years
from date of purchase for interior use and one year for exterior use.
Living Finishes – Due to the nature of Baldwin living finish products,
they will wear over time and may already have begun the process before
reaching your home. No finish warranty is offered on living finish
products, which are designed to age and improve over time. Living finishes
include raw brass, oil rubbed bronze, stainless steel, and other
non-lacquered or non-PVD finishes.
Refer to www.baldwinhardware.com for a complete warranty statement.
Problem Solution
Screws are all tight but the hardware is not
rmly attached to the door.
Check door thickness. Door must be 13⁄4” thick. Hardware will not install
on doors less than 13⁄4” thick.
Knob or lever keeps coming off the spindle. Ensure that set screw on knob or lever is fully tightened on the spindle
with allen wrench provided. Refer to Full Dummy Installation Step 7.
Rose Retainer Wrench
Rose Retainer