Installation Guide

Dummy Function Keyed Entry Lockset Installation
Door Preparation for Dummy Trim
Dummy Function Keyed Entry Lockset Installation Remember Baldwin
Exploded View Dummy Function Keyed Entry Locksets
Congratulations!
Dummy Strike Preparation
The strike needs to be installed in relationship to the direction that doors open. Whether the doors open in or out, the angled side of
the latchbolt must always face towards the stationary door when the active door is in the open position. The strike is then positioned
with the lip facing the angled side of the latchbolt as illustrated.
Caution: Before proceeding with the Door
Preparation, refer to the Dummy Strike
Preparation Illustration to ensure that the curved
section of the strike is positioned properly. Fold
the template on the line and place on the door at the
exact height of the previously installed Keyed Entry
Lockset. If the door is beveled, place the folded edge
on the low side of the bevel as shown in the illustration.
Mark the door for the face and edge bores.
Note: Dummy Trim must use same
backset as the active trim.
Caution: Re-check bore hole
locations before drilling. Drill the 2-1/8” diameter
face bore through the door and the 1” diameter edge
bore 3-1/2” deep for a 2-3/8” backset or 3-7/8” deep
for a 2-3/4” backset. The dummy latch accommodates
both size backsets.
Align the strike and trace an outline onto the door frame
using the mounting screw marks for location.
At the screw marks, drill two 1/8” diameter pilot holes
for #8 x 3/4” wood screws.
Chisel the area marked for the strike in Step 3 to a
depth of 1/16” or until the strike is flush with the door
frame. Do not install the strike at this time.
Press the dummy latch into the 1” diameter hole.
Install the strike with two #8 x 3/4” wood screws.
Install the outside knob or lever assembly so the
edges of the adapter engage the grooves in the
dummy latch.
Install the inside adapter with the spindle V-groove
on the bottom and fasten to the outside knob or
lever assembly with two 10-24 x 1-1/4” machine
screws. Make sure the “rib” features on the
adapter are at horizontal positions 3 O’clock and 9
O’clock (Fig. A). The rose will align to the ribs.
Place the rose onto the adapter. Align the cutouts
on the backside of the rose with the ribs on the
adapter (Fig. B). Hold the rose flat against the door.
Place the retainer through the adapter and thread
the retainer onto the adapter.
Slide the inside knob (or lever) onto the adapter
spindle with the set screw hole facing down.
Insert the set screw into the hole on the knob (or
lever) and thread it into the spindle shaft to attach
the knob (or lever).
V-groove
Drill 1/8” dia pilot holes
for #8 screws.
With your purchase of this solid brass lockset, you’re among a
group of discerning individuals who know the intrinsic value of
selecting the finest – Baldwin.
Our step-by-step installation instructions will help guide you
through your project quickly and easily.
Before you begin your installation, read and understand the
installation instructions and marking templates. If you have
any questions, please do not hesitate to contact our Baldwin
Technical Services Department at 1-800-566-1986. We’re
here to help!
We thank you for your purchase and wish you the fullest
enjoyment of your Baldwin lockset.
Consumer Help Line
1-800-566-1986
Hours: 8 a.m. to 6 p.m. E.S.T - Monday - Friday
10 a.m. to 6 p.m. E.S.T - Saturday
©2019 Baldwin Hardware Corporation
19701 Da Vinci, Lake Forest, CA, 92610
1
2
3
4
5
1
2
3
4
With the completion of your project, remember that Baldwin
quality hardware products are available for all your decorating
and remodeling needs. Matching entrance sets for exterior
doors, beautiful bath accessories, and a complete selection of
cabinet and door-enhancing hardware are all available from your
Baldwin retailer.
Keyed Entry Locksets
Installation Instructions
GROOVES
DUMMY LATCH
Your Baldwin lockset is now ready
for a lifetime of use.
ANGLED SIDE
INDOORS
OUTDOORS
OUTDOORS
INDOORS
DUMMY TRIM
ACTIVE TRIM
6
5
Use the retainer tool to tighten the retainer. Make
sure the rose is level before tightening.
TEMPLATE
LOW SIDE
OF BEVEL
Limited Lifetime Mechanical Warranty
Baldwin warrants that each Baldwin product shall be free from
mechanical defects at the time of delivery and for the lifetime of the
product or as long as you own your home.
Limited Lifetime Finish
™
Warranty
The Baldwin Lifetime Finish
™
uses advanced nishing technology
(physical vapor deposition) to create a nish highly resistant to the
effects of weather and normal wear and tear. The Limited Lifetime
Finish Warranty on Lifetime Finish
™
products covers the original
purchaser for as long as you own your home.
Limited Finish Warranty
The nish on Baldwin products (excluding Lifetime Finish and
living nish products) is protected by a durable topcoat designed
to maintain the beauty and quality of the Baldwin product. The
Baldwin Limited Finish Warranty covers the original purchaser for
ve years from date of purchase for interior use and one year for
exterior use.
Living Finishes
Due to the nature of Baldwin living nish products, they will wear
over time and may already have begun the process before reaching
your home. No nish warranty is offered on living nish products,
which are designed to age and improve over time. Living nishes
include raw brass, oil rubbed bronze, stainless steel, and other
non-lacquered or non-PVD nishes.
Refer to www.baldwinhardware.com for a complete warranty
statement.
PK.1234 (8/19)
Warranty Information
WOOD SCREWS
STRIKE
SET
SCREW
ROSE
RETAINER
DUMMY
LATCH
INSIDE KNOB
OR LEVER
ROSE
10-24 X
1-1/4”
MACHINE
SCREW
INSIDE
ADAPTER
OUTSIDE KNOB OR
LEVER ASSEMBLY
GROOVES IN LATCH
EDGES
9
O’CLOCK
3
O’CLOCK
FIG. A
CUTOUT CUTOUT
FIG. B
RETAINER
TOOL
ROSE
RETAINER
INSIDE
ADAPTER
ROSE
SET SCREW
ALLEN WRENCH
ADAPTER SPINDLE